Range of angled valves with brass bodies (some models chrome plated). Maximum working pressure 10 bar. Maximum operating temperature 65°C
‘Satefy group’ with a brass inlet and a DZR brass body which incorporates a lever operated spherical valve, followed by an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and a plastic bodied pressure relief valve (set at 6.0 bar). The product incorporates a test point. The compression connections are for use copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of motorised position pilot operated control valves with epoxy coated ductile iron bodies and stainless-steel pipework and fittings. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘Ballorex’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
UV disinfection unit with stainless steel body. Maximum working pressure 9.0 bar. Maximum operating temperature 55°C.
'AK99.9'. White coloured (opaque), compression moulded Alumina Ceramic material. For use with water up to 85°C.
'HYDRALFUN AC BLEU PAM RAL5005-CZL8190'. Factory applied, blue coloured acrylic paint. Apply as per manufacturer's TDS dated February 2024. Cure for 21 days@23°C. Between April 2024 and July 2024, the paint is for use with water up to 50°C. From August 2024 the paint is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HYDRALFUN AC NOIR PAM - CZL8579'. Factory applied, black coloured acrylic paint. Apply as per manufacturer's TDS dated July 2018. Cure for 21 days@23°C. For use with water up to 60°C.
'Loctite EA 109'. Factory applied, grey/beige coloured, heat cured epoxy coating. Apply as per manufacturer's TDS for Loctite ESP109 (product has changed name) dated July 2007. Cure for 2 hours@130°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Endoprene® 85-20’. Factory applied, two component, beige coloured, solvent free polyurethane coating. Mix and apply as per Technical Data Sheet dated '09/09/2019'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HY/NG' dated '2023-06-02'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 975 White'. Site applied, two-part epoxy coating which can be applied as one coat or three coats. Mix parts A & B in a 2.2:1 and apply as per manufacturer's TDS 'Ref:4236', 'Issue Date: 04/02/2015'. When applied as a single coat, the coating must be cured for 14 days at 10°C. When applied as a three-coat system, the coating must be cured as follows: coat 1 = 24 hours@10 °C, coat 2 = 24 hours@10 °C & coat 3 = 14 days@10 °C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBKOTE® E352, LUBKOTE® SG96(N96), LUBKOTE® SG98(N98)'. White coloured lubricants. Apply as per manufacturer's product data sheet 'YC20231201-1'. For use with water up to 85°C.
'ForTii Ace WX53-FC NA99001' (natural, appears beige in colour) & 'ForTii Ace WX53-FC BK00001' (black coloured). Injection moulded polyamide materials. For use with water up to 85°C.
'Acudel 22000 NT 15’ (natural - appears off-white coloured) & ‘Acudel 22000 BK 937’ (black coloured). ‘Acudel 22000 BK 937 ECHO RP’ (black coloured) was added to the approval in April 2025. Injection moulded PPSU materials. For use with water up to 85°C.
‘GFPP-(1) SFKP (2)’. White coloured, injection moulded, glass fibre reinforced PP material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% - 50%. (2) is an internal code used to denote customer and is replaced with a 4 digit number between 0001 & 9999. For use with water up to 85°C.
'6EP1862 'O' ring'. Black coloured, injection moulded EPDM 'O' ring. Shore hardness 60. Tested in-radius size 0.89mm. For use with water up to 85°C.
'EPDM 9611 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radii sizes between 0.48mm & 2.0mm. For use with water up to 85°C.
'TJJH-EPDM gasket'. Black coloured, compression moulded EPDM gasket. Shore hardness 70. Tested in-radius size 1.2mm. Between April 2024 and March 2025, the gasket was for use with water up to 23°C. Between April 2025 and April 2029, the gasket is for use with water up to 65°C.
'557WE, 557WG & 557WM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60, 70 & 90. Tested in-radius size 0.85mm. For use with water up to 85°C.
'EP02971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM BW 5950 J 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 2.0mm. For use with water up to 65°C.
'IA 608/9735'. Grey coloured, injection moulded PVC material. For use with water up to 23°C.
'IR 348/9055'. Dark grey coloured, injection moulded PVC material. For use with water up to 23°C.
Range of single-hole, single outlet (fixed) electronically operated, tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by a touch sensor. The spout outlets incorporate plastic aerators. Max working pressure 8.0 bar. Max operating temperature 65°C.
Range of BS1212-4 (2016) float operated valves for WC flushing cisterns, bottom or side entry type with plastic or brass ½’’ BSP inlet. The inlet incorporates a strainer, Compact models incorporate a delay fill function. Maximum working pressure 10.0 bar. For use with cold water only.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of spring loaded resilient trim check valve cartridges with plastic bodies, stainless steel spring and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 16 Bar Maximum operating temperature 65°C (model OV15/DN15-EPDM 31.0001.0 only) Maximum operating temperature 85°C for all other models
Range of aerators with plastic bodies and EPDM ‘O’-rings. Model (SB-BTA) incorporates a (chrome plated brass) housing. Maximum operating temperature 85°C
Range of aerators with plastic bodies and EPDM ‘O’-rings. Open outlet use only. Maximum operating temperature 65ºC.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridges and quarter turn ceramic discs headworks with single lever or dome type operating members. The spout outlets are either open outlet, waterfall or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating single sequential headworks controlling both flow and temperature with a single lever type operating member. Model A6697AA is supplied with a combined strainer, servicing valve that incorporates a single approved check valve cartridge verified by test, suitable for backflow protection to fluid category 2. Maximum working pressure; 10 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10 Bar. Maximum operating temperature 60°C.
Range of single-hole single outlet swivel combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body with various finishes) incorporating a ceramic headwork cartridge with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc or ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge, non-rising spindle or quarter turn ceramic disc headwork with either a single lever, cross top or dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies with (stainless steel bodies - various finishes), incorporating a ceramic cartridge headwork controlling the hot and cold with a single lever operating member. The boiling and purified water is controllied via a ceramic disc headwork incorporating a manual override button and a dome type headwork. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway: 98 °C; for other water pathway: 85 °C.
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted two-hole, single outlet concealed combination tap assembly (brass body – various finished trim sets), incorporating a ceramic cartridge headwork with a single lever type operating member. The spout outlet incorporates a aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body - various finishes). Incorporating a thermostatic cartridge controlling the temperature with dome operating members that incorporate a manual override button, and a quarter turn ceramic disc headworks controlling the flow with dome type operating members. The spout incorporates a lockable diverter to shower outlet and a plastic flow straightener. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8 Bar Maximum operating temperature 60°C
Range of wall mounted, three-hole single outlet (fixed) bath and shower mixers with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with cross top or single lever operating members (see model) and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted spout outlets with chromium plated brass bodies incorporating plastic aerators. Maximum operating temperature 60°C. Open outlet use only.
Range of deck mounted spout outlets (brass bodies - various finishes). Supplied with metal backnuts. Open outlet use only Maximum operating temperature: 60°C
Page 62 of 81
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
