Range of pre-set pressure relief valves (set at 3.0 bar) with nylon bodies, EPDM diaphragms and ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 85°C
Range of latching solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings.. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of normally closed solenoid valves with plastic bodies and silicone diaphragms. Model DSVP12N-12LSX-240M has two inlets. Maximum working pressure 0.060 bar. Cold water use only.
Range of brass bodied (nickel plated) spherical valves incorporating PTFE seats & chrome plated ball. Maximum working pressure 40.0 bar.
Range of brass or DZR brass spherical valves incorporating single lever operating members and a chrome plated brass ball. Model 0312A030307DC is an angled 90-degree valve which incorporates single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 or 3). For use with EN1057 copper pipe. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies and brass balls, incorporating PTFE washers. R950W models are lever operated and R951W models have a butterfly operating member. Maximum working pressure is either 42.0 bar (up to and including ¾”) or 35.0 bar (up to and including 2”). Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated, full bore spherical valves with brass bodies (brushed chrome) and chrome plated brass balls and a range of different operating members. Sizes ¼” to ½” have a maximum working pressure of 64.0 bar. Sizes ¾” to 2½” have a maximum working pressure of 40.0 bar. Cold water use only.
Range of non-rising resilient stem seated gate valves with epoxy coated bodies and EPDM wedge. Maximum working pressure 16 bar. Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron bodies ,EPDM gasket, EPDM wedge and a handwheel operating member. Maximum working pressure 25 bar. Maximum operating temperature 80°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE washers. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with ductile iron bodies (green epoxy coated) and EPDM coated ductile iron wedge. Maximum working pressure – 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermal balancing valves with brass bodies and EPDM O-rings. The products also incorporates an analogue temperature gauge. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 90°C
Range of manually operated balancing valves with either a DZR brass or bronze body incorporating a non-rising spindle balancing mechanism. Valves are adjusted using a handwheel. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
‘Pentens SPU-1000 Pure Polyurea Waterproofing Spray Coating (with Pentens E-500SE Primer and Pentens E- 501S Sealer)’. Factory applied, dark yellow coloured (once applied) polyurea primer, sealer & top coat. Mix primer in a 1:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix sealer in a 2:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix topcoat in a 1.125:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 72 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux Solvent Free DW Coating Grey and Red'. Factory applied, light grey or red coloured epoxy coatings. Apply as per manufacturer's data sheet number '558', revision '04', dated October 2022. Cure for 7 days@30°C. For use with water up to 30°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-01'. Factory applied, grey coloured, Portland cement mortar. Mix sand, cement and water in a weight ratio of 1:1:0.35 and apply as per manufacturer's user instructions 'doc: Ascent-01', 'vision: A08052023', dated '2023-05-08'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.
'TPU 2053, TPU 2054, TPU 2055, TPU 2056, TPU 2057 & TPU 2058'. Five layered, membrane systems manufactured by calendaring. The membranes consist of: 1.) a transparent polyurethane inner layer (in contact with the water), 2.) a tie layer, 3.) a reinforcing layer (PES or PA), 4.) a tie layer & 5.) a blue or beige coloured polyurethane outer layer (not in contact with the water). For use with water up to 23°C.
'VESTAMID LX9042 NC'. White coloured, injection moulded PA12 material. For use with water up to 85°C.
'RBM PE40 potable water pipe'. Black coloured (with blue external stripes), extruded LDPE pipe. For use with water up to 23°C.
'LLFA® Compression Tape'. Red coloured (with white stripe), silicone based tape, manufactured by extrusion. Shore hardness 55. Tested in-radius 0.4mm. Apply as per manufacturer's instructions 'LLFA® Compression Tape User Guide Rev. 2; July 1, 2017'. For use with water up to 75°C.
'Buffalo PUR500'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '14/08/2018'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Mungo Injection System MIT800RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'Jun-23'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP90/4 BLK Seals and 'O' rings'. Black coloured, injection moulded EPDM seals and 'O' rings. Shore hardness 90. The seals have a tested in-radius size of 1.7mm. The 'O' rings have a tested in-radius size of 1.2mm. For use with water up to 85°C.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'334701 - EPDM peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Bidet seat assembly which discharges via a push button actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test - suitable for backflow prevention against Fluid Category 5). Maximum working pressure 8 bar. Maximum operating temperature 40°C
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted single hole, single outlet (fixed), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure - 10 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of ceramic cartridge headworks with plastic bodies, incorporating silicon and NBR‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with level operating members. The spout outlets incorporate plastic aerators. The products are supplied with click wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet is a waterfall type. The products are supplied with a click type pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Range of single hole, single outlet, fixed combination tap assembly, (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate aerators and plastic flow straighteners. The products are supplied with a click type pop-up waste. Maximum working pressure 16 bar. Maximum operating temperature 60°C
Range of wall mounted, single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar or 10.0 Bar (see models) Maximum operating temperature 65.0°C or 85.0°C (see models)
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Wall mounted single hole, single outlet (fixed) combination tap assembly, brass body(various finishes), incorporating a detent headwork that controls both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator. The product also incorporates a permanently open waste outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 48 000 xxx model is supplied with a pop-up waste. The 48 001 xxx and 48 002 xxx models are supplied with an open waste/non-closing waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, swivel combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The vented models are supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ½" captive nut end connection, which provides main cold water to a venturi device which is part of a command centre (not supplied). The Arc vented models are supplied with a DZR brass tee piece, two DZR brass adaptors, two stainless-steel strainers (each combined with an EPDM washer) and a plastic flow restrictor, for installation prior to the cold inlet hose. The Arc and Cube mains models are supplied with two DZR brass adaptors and two stainless-steel strainers (each combined with an EPDM washer), for installation on each inlet hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, (swivel) combination tap assembly (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two-hole, single outlet, fixed combination tap assembly (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets for models (143106) incorporate plastic flow straighteners or a plastic aerator ,models (M33146E &153306) incorporate plastic flow straighteners & model (172306) incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C for models 179606F, 173606, 173606 MBK1, M33146E. Maximum working pressure 10 bar. Maximum operating temperature 65°C 143106, 153306, 172306
Page 54 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
