Center Brand range of brass and copper end feed fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Single low-level horizontal mount float switch with stainless-steel body and float. Maximum operating temperature 100°C.
Range of WC pressure flushing valves with a solenoid valve controlling the flow. The valves are operated via an infra-red sensor or push-button assembly. The solenoid valve also incorporates a lever operated isolation valve. Maximum working pressure – 5.0 Bar. Cold water use only
Range of stainless-steel plate heat exchangers with EPDM gaskets. The primary circuit, (excluding the E2 prefix models), incorporates a drain valve and a pump (excluding STP prefix models including an ‘N’ as the 14th figure). Operating parameters: Maximum working pressure of the secondary circuit: 6.0 bar or 10.0 bar (see model). Maximum working pressure of the primary circuit: E4 models: 6.0 bar. C3, E3, E2, i2: 10.0 bar. Models added February 2023 – Econoplate STP3, STC3, STP2, STC2 & STP4: 10.0 bar. Maximum operating temperature: Primary 140°C & Secondary 85°C.
Domestic hot water heat recovery unit incorporating a stainless-steel plate heat exchanger and cylinder. Maximum working pressure 3.0 bar. Maximum operating temperature 60°C.
Electric instantaneous, vented mains water heater with plastic a housing and silicon rubber hose. Maximum operating temperature 98°C.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Greenstar Heatslave II range of floor standing oil-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, which incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The cold water inlet incorporates a screwdriver operated spherical valve followed by a plastic flow regulator inserted within the pipework. Maximum working pressure: Primary circuit 2.5 bar. Secondary circuit 10.0 bar. Maximum operating temperature 82°C.
"Greenstar" range of indirect heat interface units and "Flow 8000" (added December 2024) range of direct heat interface units providing heating and instantaneous hot water. The heating system incorporates an expansion vessel. The products are sold with or without a prefix kit (see model), which comprises of a mounting bracket that includes spherical valves for all circuits. The "Greenstar" indirect models include a pressure relief valve (set at 3.0 bar) on the space (central) heating circuit. Greenstar models: Maximum working pressure district heating 10.0 bar. Maximum working pressure space heating 2.5 bar. Maximum working pressure secondary hot water 10.0 bar. Maximum operating temperature 60°C (secondary) and 90°C (primary). Flow 8000 models (added December 2024): Maximum working pressure district and space heating 10.0 bar. Maximum working pressure secondary hot water 10.0 bar. Maximum operating temperature 60°C (secondary) and 90°C (primary).
Water meter with a DZR brass body, stainless steel temperature sensors and EPDM ‘O’-rings. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘RSM’ range of ultrasonic water meters with blue epoxy coated ductile iron bodies, stainless steel transducer and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meter manifolds with gun metal bodies and ball valve with either a quarter turn stop valve or screw down stop valve. The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of three or four-hole single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Four hole models Incorporate quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to a shower outlet.. Three hole models Incorporate a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided PEX lined hose assemblies. The product is supplied with a shower hose and shower handset. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of concealed thermostatic mixing valves with DZR brass bodies incorporating a thermostatic cartridge controlling the temperature. The inlets incorporate asingle check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spout outlets with brass bodies (various finishes) incorporating an aerator. Product is supplied with either a lever type pop up (HIRONDELLE models) or click type waste (ICON-X & CORVAIR models). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Spout end flow control device (aerator with ‘switchable’ spray formation). Maximum operating temperature 65°C.
Range of vertical multistage pumps with stainless-steel bodies, stainless-steel impellers, shaft and outer sleeve. Maximum working pressures: T (oval flange): 16.0 bar. V (Victaullic & grooved), C (clamp flanges) & F (round flange) versions: 26.0 bar. Maximum operating temperature 100°C.
Range of multistage pumps with brass suction and discharge bodies, stainless steel housing, shaft and impeller, and EPDM ‘O’-rings and seals. Maximum working pressure: 6.0 bar (41491 & 41492 models) or 9.0 bar (41493 & 41494 models). Maximum operating temperature 65°C.
Range of filter type fixed ‘shower’ outlets and shower handsets with plastic bodies. Maximum operating temperature 45°C.
Range of filter type fixed ‘shower’ outlets and shower handsets with plastic bodies. Maximum operating temperature 45°C.
Range of shower outlets incorporating brass bodies (various finishes) and NBR ‘O’-rings. Maximum operating temperature 85°C.
Shower outlet incorporating brass body (gold effect finish), incorporating a flow regulator and EPDM O-rings. Maximum operating temperature 60ºC.
Shower head with a brass body (various finishes), incorporating EPDM O- rings and a stainless-steel strainer at the inlet. Maximum operating temperature 60.0°C
Shower handset incorporating a chrome plated plastic body and EPDM ‘O’-rings. Maximum operating temperature 60°C.
Wall mounted outlet bracket incorporating a brass body (various finishes) and EPDM ‘O’-rings. Maximum operating temperature 60°C.
Ranges of overhead shower outlets with brass bodies, chrome plated plastic shower handsets, shower sets and shower kits. The shower sets comprise of a chrome plated plastic shower handset and shower hose. The shower kits comprise of a chrome plated plastic shower handset, brass wall elbow and either stainless steel interlocked, or PVC coated, shower hoses. The inlets of the shower handsets incorporate a plastic flow regulator at the inlet. Shower kits with ½” (M) inlets are also supplied with a brass wall elbow which incorporate a plastic flow regulator and an approved single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum operating temperature 60°C.
Range of in-line `Y` patterned strainers with bronze bodies and stainless-steel strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C. Closed circuit up to 110°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Deck mounted laboratory tap, grey powder coated brass body, with three outlets: two are fixed, one is a swivel spout. Each outlet has its own individual quarter turn ceramic disc headwork controlling the flow with a dome type operating member, and a hose union attachment. The product is supplied with a brass backnut. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of pillar taps with brass bodies (various finishes) incorporating non-rising spindle headworks using either dome type or cross top operating members. Spout outlets incorporate plastic flow straighteners. The products are also supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps (chrome plated) brass bodies with quarter turn ceramic disc headworks and single lever type operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of TPE and TPS lined flexible hose assemblies incorporating NBR ‘O’-rings and various end connections. Maximum operating temperature 60°C.
Range of PET (Polyethylene terephthalate) braided flexible hoses incorporating PEX liner and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. (10.0 bar for models added September 2025). Maximum operating temperature 70°C.
Range of plastic shower hoses (chrome effect finish) incorporating a PVC inner liner, with EPDM ‘O’-rings and/or washers. Maximum operating temperature 60°C.
Range of stainless steel braided HDPE lined flexible hose assemblies incorporating EPDM ‘O’-rings and/or washers depending on end connection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of shower hoses with PVC outer (various finishes - see model), PET reinforcement layer, PVC inner liner and EPDM washers. Maximum operating temperature 65°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. SCFA models incorporate a spherical valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided, PEX lined flexible hose assemblies with a variety of end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, manually operated, concealed blending valves with brass bodies (chrome plated) faceplates, incorporating a ceramic cartridge headwork with a single lever operating member controlling both flow and temperature. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of electronic, thermostatic mixing valves which incorporate a solenoid valve on the inlet and various outlet configurations dependant on model. All models are supplied with a user interface that controls flow and temperature. The inlets of models 1.1503.678, 1.1503.682, 1.1503.690, 1.1503.698 & 1.1621.099 incorporate a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Model 1.1503.702 – Rada Sense W KIT T3 Washbasin is supplied with a wall mounted spout outlet. Model 1.1503.706 – Rada Sense S KIT T3 Shower is supplied with a fixed shower outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic bar shower valves incorporating a thermostatic cartridge controlling the temperature with a dome operating member incorporating a manual override button. The flow to the handset or overhead shower is via a ceramic disc headwork with a dome operating member. Inlets Incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. RRK models are also supplied with shower hose, handset, overhead shower head and riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 65ºC.
A range of wall mounted thermostatic blending valves with brass bodies (various finishes). The temperature is controlled via a thermostatic cartridge and dome operating member and flow is controlled via a quarter turn ceramic headwork. Product can come with one, two or three push type cartridges that divert the flow to various outlets (see model) The inlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of concealed thermostatic shower valves with brass bodies incorporating a quarter turn ceramic disc headwork controlling the flow to the shower outlet model VQ20 incorporates a single shower outlet (x1 headwork) and model VQ21 incorporates a double shower outlet (x2 headworks). The temperature is controlled independently via a thermostatic cartridge. Both inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted bar type thermostatic shower mixers with brass bodies (various finishes), incorporating a ceramic disc headwork which controls and diverts the flow to a hand shower or overhead shower using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member with a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with an overhead shower, shower hose and shower handset. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60ºC.
Range of T type thermostatic blending valves with (nickel plated) DZR brass bodies. The inlets incorporate a stainless-steel strainer and single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2) Models HEAT160030 & HEAT160035 also incorporate a servicing valve at the inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Concealed electronic thermostatic shower valve with a plastic body, the flow is controlled via two motorised valves for hot and cold supply. Both inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 7 bar. Maximum working temperature 65°C.
Range of wall mounted concealed thermostatic shower valves (brass body) incorporating a quarter turn ceramic disc headworks controlling the flow with a range of single lever, dome or hand wheel operating members. The temperature is controlled independently via a thermostatic cartridge. Both inlets incorporate stainless-steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model are available in various configurations, please see model. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted thermostatic blending valves with brass bodies (chrome plated), incorporating two way diverter valves controlling the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°.
Wall mounted thermostatic shower valves (Chrome plated) brass body. Incorporating a ceramic cartridge headwork controlling the flow to the overhead shower and shower handset using a dome type operating member. The temperature is controlled via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The inlets incorporate stainless steel strainers, screwdriver operated spherical valves and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product includes, a riser rail, shower head with a stainless-steel strainer at the inlet, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower valves (Chrome plated) brass body. Incorporating a ceramic cartridge headwork controlling the flow to the overhead shower and shower handset using a cube type operating member. The temperature is controlled via a thermostatic cartridge with a cube type operating member incorporating a manual override button. The inlets incorporate stainless steel strainers, screwdriver operated spherical valves and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product includes, a riser rail, shower head with a stainless-steel strainer at the inlet, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 52 of 234
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
