'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KLINGERSIL® C-4324'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YT-002 (natural) & YT-003 (black)'. Extruded, natural (colourless) or black coloured PVC hoses. For use with water up to 65°C.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Glidex Tap Lubricant'. White coloured silicone lubricant. For use with water up to 60°C.
'Glidex Silicone Paste'. White coloured lubricant. For use with water up to 60°C.
'Bestnyl SI40VI02BD (PA 640GF BK)'. Black coloured, injection moulded PA6 material. For use with water up to 60°C.
'KN133G50 (beige coloured) & KN133G50BL (black coloured)'. Injection moulded PA6 materials. For use with water up to 65°C.
'Pemaron660G6W NC02'. Natural (appears beige in colour), injection moulded, glass fibre reinforced PA66 material. For use with water up to 23°C.
'DH-01 Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'DH-02 Fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 65°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'LL 8460.29'. Natural (appears white and opaque) LLDPE material manufactured by rotational moulding. For use with water up to 85°C.
‘RTP 199 X 146499 S-202865 White’. White coloured (opaque), injection moulded PP material. For use with water up to 50°C.
'Tamkeen Modern Pipe White, Light Grey and Dark Grey'. Extruded PVC pipes. For use with water up to 60°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'TIMO 7 NC-70 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'AES-2/EPDM-50'. Black coloured, compression moulded EPDM sheet material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 65°C.
'E2514'. Black coloured, compression moulded EPDM rubber. Shore hardness 67. Tested in-radius size 1.03mm. For use with water up to 60°C,
'EPDM 69064340'. Black coloured, injection moulded EPDM sheet material. Shore hardness 57. Tested in-radius size 0.9mm. For use with water up to 23°C.
'RE EP/50, 'RE EP/60, 'RE EP/70 & RE EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 60°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'Brymec PVC Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'TDS Brymec CEMENT Rev 01' review date '27-05-2022'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SPS-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'S20220601' dated '2022-6-1'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body in various finishes), incorporating a ceramic disc headwork with single lever operating member (model OMI-133 & IND-OMI133-XXX) OR ceramic cartridge headwork with a single lever operating members (all other models) and a lockable self-cancelling diverter to shower outlet. All models except OMI-133-C/P and IND-OMI133-XXX are supplied with an approved check valve cartridge at the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
'6083 black'. Black coloured, injection moulded CIIR rubber material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 70°C.
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Models A7552AA and A7553AA are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Single-hole, single outlet, swivel electronically controlled tap assembly with a brass body in various finishes (see model). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating member controlling both the flow and temperature. The spout outlet incorporates a pull-out spray with a plastic aerator. The inlets incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2), and a stainless-steel strainer Maximum working pressure 5 bar. Maximum working temperature 60°C.
Range of deck mounted sensor taps. The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (models 1070021 and 1070025). Maximum operating temperature 60°C (model 1070024).
Wall mounted infra-red single hole, single outlet electronically controlled combination tap assemblies with brass body (chrome plated), incorporating a solenoid valve controlling the flow. The spout outlets incorporate a plastic aerator.Stainless steel strainer on inlet Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic flow straightener, and the inlet incorporates a plastic filter. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. The products are supplied with plastic backnuts and a stainless steel braided PEX lined flexible hose assembly for installation between the tap and the solenoid valve. Supplied with a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Wall mounted infra-red single hole, single outlet electronically controlled combination tap assemblies with brass body (chrome plated), incorporating a solenoid valve controlling the flow. The spout outlets incorporate a plastic aerator.Stainless steel strainer on inlet Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted sensor taps. The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
A range of single-hole, single outlet fixed or swivel electronically controlled tap assemblies with brass bodies in various finishes (see models). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating members controlling both the flow and temperature for all models excluding 62816, which uses a mixer to control the temperature only with a single lever operating member. The spout outlets incorporate plastic aerators. All models (excluding AZL10range) incorporate a separate approved check valve cartridge on the inlet, verified by test (suitable for backflow protection against Fluid Category 2), The inlets of all models incorporate stainless steel strainers. Maximum working pressure 5.0 bar Maximum working temperature 60°C.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a nickel plated DZR brass body. For use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC
Range of one-piece and two-piece pre-insulated GRP cold water storage cisterns. Cisterns are supplied with a float operated inlet valve, screened overflow and screened vent. Cold water use only.
Range of ceramic disc diverter headworks with or without a on/off function, to be installed in specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with plastic bodies and EPDM ‘O’-rings. All models incorporate a plastic strainer. For insertion into specifically dimensioned bores. Maximum working pressure 16 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Some models are supplied with a click waste (see model list). Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC.
Page 49 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
