Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate plastic aerators (except 2.1977.005 that has flow restrictor) and the products are supplied with plastic backnuts. Maximum operating pressure 5 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of nylon braided hoses with TPSiV inner liner and brass end connections incorporating EPDM washers.Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range of concealed, wall mounted, thermostatic blending valves, (brass bodies, chrome trim sets). The products consist of detent headworks, two-way diverter cartridges and a thermostatic cartridges (see models). All models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of T type thermostatic blending valves incorporating stainless steel strainers at the inlet. “2 IN 1” models incorporate check valve cartridges at both inlets. “4 IN 1” models have angled isolation valves at both inlets which incorporate a check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
T-type thermostatic blending valve with a brushed chrome, DZR brass body. Temperature is pre-set under a fixed cap. The inlets incorporate stainless steel strainers and single check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of concealed electronic thermostatic shower valves with a plastic body, the flow is controlled via either, 1, 2 or 3 solenoid valves which to either 1, 2 or 3 outlets (see models) and the temperature is controlled via a motorised valve operated via a control panel. Both inlets incorporate a plastic strainer. Maximum working pressure 5.0 Bar Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Range of concealed thermostatic valves with thermostatic cartridges. Models SHO001PL, SHO032VI, SHO042KL, SHO141OT, SHO020LO，SHO026PR， SHO009EL，SHO045NR, SHO047NS, SHO000PL，SHO041KL & SHO025PU consist of quarter turn ceramic disc headworks controlling the flow and the temperature is controlled independently via thermostatic cartridge. Models SHO010EL SHO002PL,SHO033VI, SHO043KL SHO142OT， SHO021LO, SHO027PR, SHO046NR & SHO049NS consists of a two-way diverter cartridge controlling the flow and a thermostatic cartridge controlling the temperature. Model SHO012PR consists of a three-way diverter cartridge controlling the direction of flow, a thermostatic cartridge controlling the temperature and a quarter turn ceramic disc controlling the flow. All models incorporate cube, dome, cross-top or single lever type operating members. The inlets incorporate stainless steel strainers and single check valve cartridges; however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with a cube operating member incorporating a manual override button. The temperature is controlled by a thermostatic cartridge with dome or cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets of all models incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C except for models VAH0347 - 5059340245775 & VAH0348 - 5059340245782 both 60°C
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets of all models incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets of all models incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C except for models 623224 & 623229 both 60°C.
Range of wafer and lugged butterfly valves with blue epoxy coated ductile iron bodies and stainless steel disc. DN50-DN300 are lever operated and DN350 – DN600 are handwheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer or lug type butterfly valves with blue epoxy coated cast or ductile iron bodies, blue epoxy coated ductile iron or stainless-steel discs and EPDM seats. Leaver or hand wheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lugged and double flanged type butterfly valves (with blue epoxy coated ductile iron bodies, and either a stainless steel or grey epoxy coated ductile iron disc with an EPDM liner. Maximum working pressure 16.0 Bar (DN50 to DN800) or 10.0 Bar (DN900 to DN1200)
Non-metallic materials and components comply with BS6920 at 60°C
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of brass or DZR brass spherical valves incorporating single lever operating members and a chrome plated brass ball. Model 0312A030307DC is an angled 90-degree valve which incorporates single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 or 3). For use with EN1057 copper pipe. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies and brass balls, incorporating PTFE washers. R950W models are lever operated and R951W models have a butterfly operating member. Maximum working pressure is either 42.0 bar (up to and including ¾”) or 35.0 bar (up to and including 2”). Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated, full bore spherical valves with brass bodies (brushed chrome) and chrome plated brass balls and a range of different operating members. Sizes ¼” to ½” have a maximum working pressure of 64.0 bar. Sizes ¾” to 2½” have a maximum working pressure of 40.0 bar. Cold water use only.
Range of gate valves with bronze bodies and bronze wedges. The valves operate via non-rising spindle head work with hand wheel or lock shield operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of manually operated balancing valves with either a DZR brass or bronze body incorporating a non-rising spindle balancing mechanism. Valves are adjusted using a handwheel. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
'SSIC-C/S1.S9.S12'. Grey coloured carbon graphite/silicon carbide ceramic ring manufactured by sintering. For use with water up to 85°C.
'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2012-8-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-OPC (N)'. Factory applied, grey coloured Ordinary Portland Cement. Mix and apply as per manufacturer's work instructions 'JSGL/WI/14', issue '02', revision '00', dated '29.09.2018'. Cure for 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE GeoSpray Mortar'. Site applied, grey coloured, geopolymer cementitious material. Mix 300g of powder with 60ml water and apply as per manufacturer's instructions 'V: 09.06.2022'. Cure for 96 hours@3°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'VESTAMID LX9042 NC'. White coloured, injection moulded PA12 material. For use with water up to 85°C.
'TP12939 Natural'. Natural (appears off-white) polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'TP12978 Black'. Black coloured, polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'EP90/4 BLK Seals and 'O' rings'. Black coloured, injection moulded EPDM seals and 'O' rings. Shore hardness 90. The seals have a tested in-radius size of 1.7mm. The 'O' rings have a tested in-radius size of 1.2mm. For use with water up to 85°C.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'Ganga 50, 60, 70, 80 & 90'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 90 ShA. Tested in-radius size 1.1mm. For use with water up to 85°C.
'JJSXEPDMIRHD50 (shore hardness 50) & JJSXEPDMIRHD70 (shore hardness 70)'. Black coloured, compression moulded EPDM materials. Tested in-radius size 0.99mm. For use with water up to 23°C.
'01/E90FKM Gaskets & 'O' rings'. Black coloured, injection moulded FKM gaskets & 'O' rings. Shore hardness 90. The gaskets have an in-radius size of 1.1mm and the 'O' rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Bidet seat assembly which discharges via a push button actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test - suitable for backflow prevention against Fluid Category 5). Maximum working pressure 8 bar. Maximum operating temperature 40°C
Range of single hole, single outlet, electronic touch free, deck mounted taps (chromium plated brass) for cold or premixed water. Flow is controlled via solenoid valves, actuated by infra-red sensors. Power is supplied by externally mounted 9V battery pack or 9V transformer. The inlet hoses have a stainless-steel strainer and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes - see model). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The TK-201LT66 and TK-201LT95 models have a multi-layer PEX lined hose between the solenoid and the spout. The TK-201LT65 models have a stainless steel braided PEX lined flexible hose between the solenoid and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 46 of 83
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
