'EVER-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'JSP-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Belzona 1511 (Super HT – Metal)'. Site applied, two-component, silver/grey coloured (once mixed) epoxy coating. Mix parts A and B in a 5:1 mass ratio and apply as per manufacturer's instructions for use 'FN10178', publication number '07-06-21'. Cure for 18 hours@20°C then post-cure for 1 hour@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ePIPE® UK'. Site applied, red-brown coloured, two-part epoxy based coating consisting of a based and activator. Mix base and activator in a 2:1 mass ratio and apply as per manufacturer's IFU issue '009', dated March 23, 2011. Air-cure for 60 minutes@25°C and then immerse in a water bath at 60°C for 60 minutes. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Regin REGQ102-115'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Tecomid NB30 GR50 BK012 QW'. Black coloured, injection moulded PA6 material. For use with water up to 85°C.
‘Radilon A RV300RKC 106 NT, A RV300RKC2 106 NT, A RV500RKC2 106 NT & A RV500RKC 106NT’ ‘Radilon A RV300RKC 306 BK, A RV500RKC 306 BK, A RV300RKC2 306 BK & A RV500RKC2 306 BK’. ‘NT’ indicates that the grade is natural (which appears beige in colour). BK indicates that the grade is black coloured. Injection moulded PA66 materials. For use with water up to 85°C.
'4MID 9B22150 W-A BBK'. Black coloured, injection moulded PA6 material. For use with water up to 85°C.
'Poseidon Cable' (3 x 1.5mm, 4 x 1.5mm, 3 x 1.0mm & 4 x 1mm). Blue coloured (external water contact layer), extruded, XLPE electrical cable. For use with water up to 65°C.
'Jain HDPE (PE 100) Blue Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'Jain HDPE (PE 100) Black Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
‘Dowlex 2631UE & Dowlex 2631.10UE’ Natural (appear white coloured). ‘RX 102 Natural, RX 102 Black 9003 & RX 102 GR Black 9003’ (black coloured). In April 2025 ‘RX102 Blue 6263’ (blue coloured) was added to the approval. Rotationally moulded polyethylene materials. For use with water up to 70°C
‘Dowlex 2629UE & Dowlex 2629.10UE’. ‘RX 101 Natural, RX 101 Black 9003 & RX 101 GR Black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Sabic R50035EE’. ‘RX 806 Natural, RX 806 Black 9003, RX 806GR Black 9003, RX 820 Light Blue 6001 & RX 820GR Light Blue 6001’. Natural (appears white coloured), black and light blue coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Borsafe HE3494-LS-HP’. Blue coloured HDPE material for injection moulding and extrusion. ‘Borsafe HE3490-LS-HP & Borsafe HE3490-LS-HW’. Black coloured, HDPE materials for injection moulding and extrusion. ‘Borsafe HE3490-IM-W’. Black coloured, HDPE material for injection moulding. ‘Borsafe HE3490-SLS-H’. Black coloured, HDPE material for extrusion. All grades are for use with water up to 60°C.
‘FILTER NOZZLES P, PTL, P5, P6, P7, T, TTL, TD, R, RTL, RD, B, V, VL, C, D4, D3 & D9. NUTS N & HR. EXPANDING BOLT TS. VALVE BODIES DPI & DPS. SLEEVES G, GM & GE. COLLECTORS CSI05, CSI06, CST06, CSD06, CSI08, CST08, CSG08, CSD08 & CSI08. FILTER ARMS SF/SFC, SD, SB & SC. FILTER NOZZLES RB2 & RB3. DISTRIBUTORS RBD2 & RBD3’. Blue, black, dark grey, light grey, green, red, yellow & light blue coloured, injection moulded polypropylene components. For use with water up to 23°C.
‘Verplen C30 01 NE ACLKUV (black coloured), C30 04 NE ACLUV (black coloured), C30 08 NE ACLKUV (black coloured) & C30 08 NT ACLKUV (natural – appears beige coloured)’. Injection moulded, glass filled polypropylene materials. For use with water up to 60°C.
'ABR-PS'. Black coloured, injection moulded polystyrene material. Between July 2022 and 14th February 2023, the material is for use with water up to 23°C. From 15th February 2023 until July 2027, the material is for use with water up to 60°C.
`Soltane F/B 197`. White coloured, extruded thermoplastic polyurethane material. For use with water up to 60°C.
'HW-EPDM SH 50'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 65°C.
‘Addisil 1050E, 1060E, 1070E & 1080E’. Un-pigmented (appear white in colour), translucent, extruded, silicone rubber sheet materials. Shore hardness between 50 & 80. Tested in-radius size of 2.1mm. For use with water up to 85°C.
'40810813 (3019 THF Free)'. Colourless (transparent) solvent cement. Apply as per manufacturer's fact sheet 'TDS00481' dated 20th July 2018. Cure for between 24 hours and 21 days@7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Astral PVC Gel'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions review date '2019-09-11'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PK-HM 8 natural (6145) & PK-VM 8 natural (6146)’. Natural (appear beige in colour), injection moulded polyketone materials. For use with water up to 85°C.
Range of deck mounted, four hole, single outlet (fixed) combination tap assemblies with brass bodies, incorporating ceramic cartridge headworks with a single lever operating members, the spout outlets incorporate flow straighteners and there is a manual diverter to the shower handset. The product is supplied with a shower hose and handset. The headworks, spout and shower outlet are connected via flexible hoses. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, four hole, single outlet (fixed) combination tap assemblies with brass bodies, incorporating quarter turn ceramic disc headworks with either single lever, cross top or dome type operating members and a manual diverter to the shower handset. The product is supplied with a shower hose and handset. The headworks, main body and shower outlet are connected with hoses. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
'3P-Pipe'. Cream coloured, extruded uPVC pipe. For use with water up to 65°C.
'3P-Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 65°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. The trigger on the pull-out controls optional spray. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of WC flushing cisterns incorporating a side entry BS 1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16 Bar. Maximum operating temperature 65°C
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of deck mounted side valve with brass bodies and chrome trim sets. Models PDV030, PDV032, PDV067, PDV068 incorporate quarter turn ceramic disc headworks and models PDV029, PDV031 incorporate half turn ceramic disc headworks with various operating members (See models). Models PDV 031, PVD 032 and PVD 068 are supplied with metal back nuts. Models PDV 029, PDV 030 and PDV 067 are supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates either a combined EPDM washer and stainless steel strainer with a plastic flow straightener, or an EPDM washer with a plastic aerator. The product is supplied with a click type waste, verified by test. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with either a single lever or dome type operating member (see model). The spout outlet incorporates a plastic aerator (specific models only - see model section). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with either a single lever, cross top or dome type operating member (see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a waterfall type with or without a stainless-steel mesh (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product can be supplied with a pop-up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Model TVW112001000 and TVW112002000 are supplied with pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks with dome type operating members for models (163108, 163108E) and a cross-top operating member for model (163108F). Model (163208) incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating a brass body and ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The product also incorporates a separate ¼ turn ceramic disc headwork which supplies a stainless steel braided PEX lined flexible outlet hose assembly incorporating a ½” BSP (M) end connection. This outlet hose is supplied with an optional fibre gasket and ½” BSP (F) x ¾” BSP (M) brass adaptor and is intended to supply an appliance, with the quarter turn ceramic disc headwork acting as a shut-off valve. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chromium or matt black finish), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with a single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. This product also incorporates an additional spring-loaded quarter turn ceramic disc headwork with a single lever operating member for filtered cold water discharged from the spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The spout outlet incorporates a plastic aerator. The 80CR256TH model is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 39 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
