Range of stainless-steel inter-locked and PVC braided PVC lined flexible hose assemblies. Maximum operating temperature 65.0°C
‘Comet’ combination units consisting of a cased and insulated stainless steel unvented hot water storage cylinder. The cylinder primary circuit is fitted with an in-line electrical heater which supplies the heat source to the secondary water via a stainless-steel coil, and the heat source to the central heating circuit directly. The cylinder is factory fitted with a temperature and pressure relief valve, pre-set at 7.0 bar 90 degrees. The unit is supplied with an inlet control group containing a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), pressure reducing valve set at 3.0 bar and an expansion relief set at 6.0 bar. An expansion vessel is factory fitted to both the secondary and primary circuits within and is positioned inside the casing. The primary circuit also incorporates a circulating pump and pressure relief valve which is set at 3.0 bar. Maximum secondary working pressure 5.5 Bar Maximum Primary working pressure 2.5 Bar Maximum operating temperature 65.0 °C
Range of wall mounted, concealed, manual blending bath shower mixers (brass bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter (to divert the flow between a shower outlet or bath spout outlet - not supplied). The products comprise of a basic set, (concealed body), which includes the ceramic cartridge and a finish set that includes the self-cancelling diverter, headwork collar, operating member and trim set. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with a lever operating member. Temperature is controlled independently via a thermostatic cartridge with a single lever operating member. Both inlets incorporate an eccentric isolation valve, a stainless-steel strainer and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides back flow protection. The shower outlet connection on the main valve incorporates a flow restrictor (H9741 model only). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
A range either concealed or exposed wall mounted thermostatic mixing valves with brass bodies (exposed models are chromium plated). Models F3004, F2301, F2304, F2303 incorporate ¼ turn ceramic disc headworks. Model F2304, F2092, F2302 incorporate a manual diverter with a shut off. All models incorporate a thermostatic cartridge that controls the temperature, expect model F3002 that incorporates a combined shut off a thermostatic cartridge with single lever operating members. Model F3004 has a single lever operating member for the headwork and a cross top operating member for the thermostatic cartridge. The inlets of all models expect F3004 incorporate stainless steel filters and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Range of concealed thermostatic mixing valves, incorporating quarter turn ceramic disc headworks, with dome type operating members, controlling the flow to multiple shower outlets. The temperature is controlled independently via a thermostatic cartridge with dome type operating member. The inlets incorporates stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model 65036+54073 supplied with a shower handset and hose. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Wall mounted, thermostatic shower valve (chromium plated brass). Flow is controlled by a quarter turn ceramic disc headwork with single lever operating member. Temperature is controlled independently by a thermostatic cartridge with a cross-top operating member that incorporates a manual override button. The product is supplied with a shower rail and overhead shower. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Concealed, thermostatic shower blending valve, incorporating a brass body and a (chrome plated) trim set. The trim set comprises of a 2 way ceramic disc diverter headwork with a dome type operating member controlling the flow, and a thermostatic cartridge controlling the temperature with a dome type operating member incorporating a manual override button. The trim set is also supplied with two brass assemblies comprising of a plastic filter, EPDM ‘O’-rings and an approved check valve cartridge, however the complete assembly has not been tested to demonstrate it provides adequate backflow protection.. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted exposed thermostatic mixing valves with brass bodies (various finishes). Incorporating a ceramic disc headwork with single lever operating member controlling the flow of the outlet on the bottom of the valve and three push button cartridges, two control the flow to outlets at the rear of the valve, and one to the outlet on the bottom of the valve all with cube type operating members. The temperature is controlled independently via thermostatic cartridge with a dome type operating member with a manual override button. The inlets and outlet at the bottom of the valve incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum working temperature 65°C.
Range of wall mounted exposed thermostatic mixing valves with brass bodies (various finishes). Incorporating a ceramic disc headwork with a single lever operating member controlling the flow to a hose outlet and then two push button cartridges, one controls the flow to an outlet at the rear of the valve and the other to the outlet on the bottom of the valve with cube type operating members. The temperature is controlled independently via thermostatic cartridge with a dome type operating member with a manual override button. The inlets and outlet at the bottom of the valve incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum working temperature 65°C.
Range of wall mounted, bar type thermostatic shower mixers (various finishes). Incorporating a quarter turn ceramic disc headwork controlling the flow to the outlet with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member with a manual override button. Both inlets incorporate stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70ºC.
Range of concealed, wall mounted thermostatic blending valves (cast brass bodies). All models incorporate a thermostatic cartridge to control the temperature. GOO.5500AE/W/A00 model has a top outlet with a 2 way diverter controlling the flow. GOO.5600AE/W/A00 model has a top outlet with a 3 way diverter controlling the flow. GOO.5540AE/W/A00 model has a top outlet with a 2 way diverter and a bottom outlet with a quarter turn ceramic disc headwork controlling the flow. GOO.5200AE/W/A00 model is just a thermostatic cartridge (no flow control). GOO.5300AE/W/A00 model has a top outlet with a quarter turn ceramic disc headwork controlling the flow. GOO.5300AE/W/A00 model has a top and bottom outlet both with a quarter turn ceramic disc headwork controlling the flow inlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of T-type thermostatic mixing valves with DZR brass bodies. The inlets incorporate a stainless-steel strainer and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10 Bar Maximum operating temperature 90°C
Range of wall mounted concealed thermostatic mixing valves with brass bodies. Flow is controlled by either a 2-way combined shut off/diverter cartridge or a ceramic disc headwork with various operating member (see models). The temperature is controlled independently via a thermostatic cartridge with a various operating member that also incorporates a manual override button. The inlets incorporate a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, thermostatic shower valve with chromium plated brass body. Flow is controlled by a quarter turn ceramic disc headwork with a single lever operating member. Temperature is controlled independently by a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with shower hose, handset, and riser rail. Maximum working pressure 10.0 Bar Maximum operating temperature 70°C.
Three-hole deck mounted thermostatic blending valve with brass body (chromium plated brass) incorporating a ceramic cartridge headworks with single lever operating members and a lockable self-cancelling diverter to shower outlet. The inlet to the shower handset incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum working temperature 60°C
Three-way diverter valve with a stainless-steel body and stainless-steel ball. Maximum working pressure 9.8 bar Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies adjustable between 1.0 and 6.0 bar. The valves incorporate a stainless steel strainer. Maximum supply pressure 25.0 bar or 16.0 bar (see model). Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of normally open, non-latching solenoid valves with brass bodies and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of normally closed solenoid valves with brass bodies, stainless steel spring, EPDM seal and diaphragm. Maximum working pressure 9.80665 bar. Maximum operating temperature 85°C.
EV220 BW range of normally closed solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of lever operated spherical valves incorporating brass bodies (nickel plated), brass balls (chrome plated) and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brushed chrome brass bodies, chrome plated brass ball incorporating a PTFE seat and NBR O rings. For use with EN1057 copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10.60982.015.CP12-8510) Maximum working pressure 25.0 bar (model 10.62022.015.CP12-8510) Maximum working pressure 40.0 bar (models 10.61062.015.CP12-8510 & 10.61062.022.CP12-8510) Maximum operating temperature 85°C.
Range of inline or angled ball valves with brass or nickel-plated brass bodies, chrome plated brass balls and a lever, butterfly or lockshield operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Gate valve with an blue epoxy coated cast iron body, EPDM packing and seal. The valve operates via a hand wheel. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of in line double regulating valves with DZR brass bodies, EPDM ‘O’-rings and PTFE valve seals. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function with a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
‘KHS CoolFlow’ range of cold water thermostatic balancing valves, incorporating gunmetal bodies,PTFE seats and EPDM ‘O’-rings. The 6150G01500 and 6160G01500 models are servo controlled (230V and 24V respectively), the 6170G01500 model is manually controlled. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel bodies & quartz tubes. All models incorporate a spherical valve on the drain outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C
'AD-94 Sealing Ring'. White coloured, compression moulded ceramic sealing ring. For use with water up to 85°C.
'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Blue coloured, factory applied, Fusion Bonded Epoxy Powder Coating. Apply as per manufacturer's application guide dated 'October 2018'. Cure for 5 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JPC Liquid Epoxy Paint'. Factory applied, red coloured, two-component epoxy paint. Mix components A & B in a 3:1 volume ratio and apply as per manufacturer's instructions ' JPC-FG-A/06-21/009 & JPC-FG-B/06-21/009' dated '02/06/2021'. Cure for 7 days@34°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LNXFSY'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X202101207F' dated '2021-12-07'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Desmopol DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'DESMOPOL DW v.11-03-2022'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote® 48-20'. Factory applied, blue coloured, two component epoxy coating consisting of a resin and hardener. Mix resin and hardener in a mass ratio of 68:32 and apply as per manufacturer's TDS dated 10/12/2018. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikalastic P 770’ (formerly known as ‘MasterSeal P 770’) Primer for use with ‘Sikalastic M 808’ (formerly known as ‘MasterSeal M 808 Grey’, and ‘MasterSeal M 808 Light Grey’) topcoats. Site applied coating system, which is light grey coloured (once mixed and applied), comprising of a primer and polyurethane coatings. Coat 1 primer: Mix parts A & B of ‘Sikalastic P 770’ Primer in a weight ratio of 2.2:2.8. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 24 hours@7°C. Coat 2 (coating): Mix parts A & B of ‘Sikalastic M 808’, dark grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 6 hours@7°C. Coat 3 (water contact coating): Mix parts A & B of ‘Sikalastic M 808’, light grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 7 days@7°C. When applying the coating system to GRP there is no need to apply a primer. Mix, apply and cure ‘Sikalastic M 808’ dark grey and then mix, apply and cure ‘Sikalastic M 808’ light Grey (water contact layer) as detailed above. For use with water up to 23°C.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Klingersil® C-4240'. Fibre gasket material, manufactured by calendaring, which is beige coloured on one side and off-white coloured on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
'K422'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'May 2022'. For use with water up to 85°C.
'Zytel® FG101L NC010 & Zytel® FG42A NC010'. Un-pigmented (appear off-white, translucent), injection moulded nylon materials. For use with water up to 23°C.
Page 31 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
