`R2 Red & R2 Blue`. Factory applied epoxy powder coatings manufactured in Changzhou. Apply as per manufacturer's instructions for use 'ANCZ-RAD-W501', 'revision no: 2' dated 'May. 5th 2021'. Cure for 10 minutes@200°C. For use with water up to 80°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001 Blue`, factory applied, blue coloured, fusion bonded epoxy coating. 'Jotaguard VA 5001 Red`, factory applied, red coloured, fusion bonded epoxy coating was added to the approval in June 2023. Apply both coatings as per Jotun Technical Data Sheet issued 9th November 2015. Cure for 5 minutes@245°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubotapowder TK1413F'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions 'GR-294E' dated 2018/10/01. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB-108'. Factory applied, two-component, grey coloured epoxy coating. Mix, apply and full cure (7 days@20°C) as per manufacturer's technical data sheet 'file no. TWJ-WB-108', 'edition: A1' dated 01/12/2020. For use with water up to 65°C.
'Epoxy phenolic FBE-4 RAL 5010'. Factory applied, blue coloured epoxy phenolic coating. Apply as per manufacturer's instructions dated '11/20'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOXY TB BT Grey RAL 7016'. Factory applied, grey coloured, fusion bonded epoxy coating. Apply as per Technical Data Sheet 'document version:1' dated 'June 22, 2021'. Cure for 10 minutes@160°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Karumel EX4412 Blue & Grey’. Factory applied, blue or grey coloured, epoxy resin based powder coating. Apply and cure as per manufacturer’s instructions reference 'PCA-21062901', issued August 2021. For use with water up to 85°C.
`3011 high chlorinated polyethylene anticorrosive coating`. Factory applied, burgundy coloured polyethylene coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per Technical Data Sheet file no. 'TWJ-H-453', edition 'A2', dated '01/03/2020'. Cure for 5 days@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`9011 Epoxy anticorrosive coating`. Factory applied, black coloured epoxy coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18, 2020. For use with water up to 23°C.
'KINTE Epoxy Resin Coating (ES-BL10724-S9)'. Factory applied, blue coloured coating. Apply and cure as per manufacturer's instructions issued 'March 2018 V5.2'. For use with water up to 85°C.
'FY-6 (white coloured) & FY-5 (blue coloured)'. Factory applied epoxy powder coatings. Apply and cure as per manufacturer's instructions ‘fyzj2020925 version 1' dated '2020-9-20'. For use with water up to 85°C.
'GP HBSL EPOXY'. Factory applied, brown coloured epoxy coating. Mix and apply as per manufacturer's standard operating procedure document number 'GP/SOP/HBSL/001', version '01' dated 1st April 2019. Cure for 17 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jazeera Proofex (formerly known as Jazeera Proof DW)'. Site applied, two-component, grey coloured cementitious coating. Mix Part A (grey coloured powder) with Part B (white, opaque liquid) in a 2:1 mass ratio. Cure for 28 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Brushbond FLXIII'. Site applied, grey coloured, two-part elastomeric/cementitious coating. Mix and apply in accordance with manufacturer's instructions 'v10' dated October 2020. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Superfast Potable Water (SFPW)'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's instructions 'SOP Number RM1 version 1.0', dated '06/10/2022'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Extralite Pipe'. Light green/brown coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'Extralite Fitting'. Brown coloured GRP fitting manufactured by hand lay-up. For use with water up to 60°C.
'ajpipe GRP Pipe'. Beige coloured GRP pipe manufactured by continuous filament winding. For use with water up to 23°C. From February 2024, the pipe is for use with water up to 60°C.
'SNB GRP Panel'. Beige coloured, hot press moulded GRP panel. For use with water up to 50°C.
'S-006TG'. Cream coloured, compression moulded GRP panel. For use with water up to 23°C.
'XIN-6709-01 hose' manufactured from 'GR-PVC 001N' raw material. Single layered, extruded, black coloured PVC hose. For use with water up to 85°C.
'Purolite® A600E/9149'. Yellow coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A502PS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A860S'. White coloured ion exchange resin. For use with water up to 23°C.
'REGZ40 & REGZ41'. White coloured silicone greases. For use with water up to 85°C.
`Griffon P-20` Lubricant. White coloured lubricant in the form of a paste. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Omnix DW/FC-4050 NT000'. Natural (off-white with yellow/green tint coloured), injection moulded PA material. For use with water up to 23°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Between September 2020 and February 2022 these grades are for use with water up to 85°C: Grivory HT1V-3 FWA natural. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey 9312. Grivory HT1V-4 FWA natural. Grivory HT1V-5 FWA Grey L1366.3. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-4 FWA grey-blue 4637. The natural coloured Grivory may also be coloured using MB A XE 4298 black (using the recommended dosage). Between September 2020 and February 2022 these grades are for use with water up to 23°C: Grivory HT1V-3 FWA black 9225. Grivory HT1V-4 FWA black 9225. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-6 FWA natural and black 9225. From March 2022, all grades are suitable for use with water up to 85°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Between September 2020 and February 2022 these grades are for use with water up to 85°C Grilamid LV-65H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-30H FWA natural. Between September 2020 and February 2022 these grades are for use with water up to 23°C Grilamid LV-50H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural. From March 2022, all grades are suitable for use with water up to 85°C.
'Sirester EC 0994/AT/V/15'. Pale green coloured orthothalic resin manufactured by hand lay-up. For use with water up to 23°C.
'100 US Gallon Dubai Polytank Panel'. Triple layered, rotationally moulded LLDPE tank panel comprising of a white coloured inner layer, black coloured middle layer and white coloured outer layer. For use with water up to 65°C.
'Radius Systems Socket Fittings and Saddle Fittings'. Black coloured, injection moulded PE fittings. For use with water up to 60°C.
'Revolve 6402U'. White coloured (translucent), polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'PE-BWG'. Transparent, extruded, single layer, polyethylene hose. In July 2023, 'PE-BWG Black', a black coloured (opaque), extruded, single layer, polyethylene hose was added to the approval. For use with water up to 85°C.
'BKBB-660'. Black coloured LLDPE 'buoyant body' manufactured by rotational moulding. For use with water up to 23°C.
'XSPE-GPE01'. Black coloured (with blue stripes), extruded polyethylene pipe. For use with water up to 23°C.
'Hostalen GM 5010 T3 Black'. Black coloured, extruded HDPE material. For use with water up to 23°C.
'HD 8570.29'. Natural (appears white with black specks), high density polyethylene resin material manufactured by rotational moulding. For use with water up to 85°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'Durafide® 1130A1T WF900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WF9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'DIC. PPS FZ-2140 BLACK'. 'DIC.PPS FZ-2140 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'DSA Pipe'. Grey coloured extruded PPR pipe. For use with water up to 70°C.
'DSB Fitting'. Grey coloured, injection moulded PPR fittings. For use with water up to 70°C.
Page 30 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
