Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with a dome or cube operating member incorporating a manual override button. The temperature is controlled by a thermostatic cartridge with dome or cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless steel or ductile iron discs (nickel plated). The products are supplied with either bare shaft or with lever or gear operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of wafer and lugged type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs and EPDM seat. The closing mechanism can be controlled by either a lever, gear or bore shaft. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. D71X4, D71XLV4 & D41X4 models incorporate a hand wheel operating members and D371X4, D371XLV4 & D341X4 incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and disc, incorporating an NBR seat and hand wheel operating member. Maximum working pressure 10.0 bar. Cold water use only.
Ceramic disc shower to shower diverter cartridge incorporating a plastic body for use in specifically dimensioned bores. Maximum working pressure 16 bar. Maximum operating temperature 65°C.
Wall mounted, brass bodied shower control valve incorporating a quarter turn ceramic disc headwork with a chrome plated trim set and operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of non-return valves housed within black epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valves with DZR brass bodies, integral stainless steel strainer, and EPDM ‘O’-rings and membrane. The oulet pressure is adjustable between 1.5 bar and 6.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 70°C.
Range of pressure reducing valves with DZR brass bodies adjustable between 1.0 and 6.0 bar. The valves incorporate a stainless steel strainer. Maximum supply pressure 25.0 bar or 16.0 bar (see model). Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar or 1.0 and 12.0 bar (see model). Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of adjustable in-line pressure reducing valves, the inlets incorporate a stainless-steel strainer. Models TS-504-505 & TS-506-508 have brushed chrome, DZR brass bodies. Model TS-501-503 has a DZR brass body. Maximum supply pressure 8.0 bar. Maximum outlet pressure 1.0 bar to 6.0 bar. Maximum operating temperature 85°C.
Range of pre-set angled pressure relief valves for use on primary closed circuits, incorporating DZR brass bodies, EPDM diaphram and EPDM or NBR ‘O’-ring. For maximum working pressure please refer to model. Maximum operating temperature 99°C.
A range of screwdriver operated spherical valves with brass bodies and brass ball, EDPM ‘O’-rings and fibre washers. Maximum working pressure 16.0 bar, Maximum working temperature 85°C.
Range of inline and angled screwdriver or lever handle operated spherical valves with (chromium plated) brass bodies, chromium plated brass ball, NBR ‘O’-rings. For use with copper pipe manufactured to EN 1057 Maximum working pressure 16.0 bar at 30°C and 5 bar at 99°C Maximum working pressure 6.0 bar. Maximum operating temperature 90°C (model TX480 only)
Range of spherical valves with either chrome plated brass, nickel-plated brass, or brass bodies (See models) with a chrome plated brass ball and PTFE seats. Models TS-1212, TS-1202, TS-1101, TS-1201 and TS-1111 have lock shields, models TS-1271, TS-3012, TS-3001, TS-2001 and TS-2042 have lever operating members Maximum working pressure 25 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves incorporating nickel plated brass bodies, chrome plated brass balls & Tee type operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
ISIS range of single lever and T type operated spherical valves with DZR brass body and ball (chrome plated), and PTFE seals. Maximum working pressure 40.0 bar (¼”, 3/8”, ½”, ¾”, 1”, 1 ¼”, 1 ½”, & 2” models) Maximum working pressure 10.0 bar (2 ½”, 3” & 4” models) Maximum operating temperature 100°C
Range of spherical valves with brass bodies (brushed chrome plated), (red coloured) lever operating members and chrome plated brass ball. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass bodies, brass ball, PTFE washer and seats, incorporating a butterfly handle operating member (R254 models) or single lever operating member (R254DL models). Maximum working pressure 42.0 bar (¼ - ½” models). Maximum working pressure 35.0 bar (¾” - 2” models). Maximum operating temperature 99°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lock shield or handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating an NBR wedge and non-rising spindle with hand wheel operating member. Maximum working pressure 16.0 bar. Cold water use only.
Range of undercounter and passthrough commerical dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). The inlet hose incorporates a stainless steel strainer. Maximum working pressure 4.0 bar. Maximum operating temperature 55°C.
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
'FC941'. Black coloured, injection moulded, carbon graphite bearing. For use with water up to 85°C.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. Resicoat R4 blue R4-FB HJC06R & R4-ES HJF26R. Resicoat R4 red/red-brown R4-ES HGF03R. Resicoat R4 black R4-FB HNC01R. Resicoat R4 black: R4-ES HNF04R.
‘PVEF undercoat with Fluiglide Topcoat’. Factory applied, cream coloured (once mixed and applied), coating system comprising of ‘Polyglass VEF’, two-component glassflake vinyl ester undercoat and ‘Fluiglide’, two-component polyester topcoat. Mix and apply ‘Polyglass VEF’ in accordance with Corrocoat ‘product reference 2/23’ dated ‘5th June 2007’ and last reviewed ‘March 2022’. Cure for 24 hrs@20°C (±1°C). Mix and apply ‘Fluiglide’ in accordance with Corrocoat ‘product reference ‘4/01’, valid from ‘23rd October 1995’ and last reviewed ‘March 2022’. Cure for a minimum of 6 days@20°C (with a lower tolerance of -1°C). These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GTH-CC Iron Red'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Ice Grey'. Factory applied, two-component, white coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add PLUS 2.5'. Grey coloured, site-applied waterproofing admixture. Admixture is to be added to cement mix in a dosing ratio of 2.5 kg per m3 of concrete. Cure for 5°C for 48 hours. For use with water up to 23°C. This material is only approved for the dosing and curing conditions that appear on the approval. If the dosing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BELPA CSA 45'. Beige coloured fibre gasket material manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'IKV Tribosil MHL 40'. Clear silicone liquid lubricant. Apply as per manufacturer's technical data sheet. No cure required. For use with water up to 85°C.
'Anisotropic Ferrite Special Grade PF-S/3.5/2/4/SM'. Grey coloured, sintered Strontium Ferrite Magnet. For use with water up to 23°C.
'Akoalit PB 4268 White & Akoalit PB 4267 Grey'. White or grey coloured, extruded polybutylene material. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 TM-Z1 Alpinweiss 230c'. White coloured, injection moulded, glass fibre reinforced PBT material. In January 2024, 'Badadur PBT9 GF10/GK20 alpinweiss 230c' was added to the approval. Both grades are for use with water up to 65°C.
‘Ultrason® E 2010 G4 Uncoloured’. Beige coloured, injection moulded polyethersulphone material. For use with water up to 85°C.
‘Ultrason® P3010 MR White 20264’. White coloured, injection moulded polyphenylsulfone material. For use with water up to 85°C.
‘Meti UPVC Fittings’. Grey coloured, injection moulded uPVC fitting. For use with water up to 40°C.
'LSPVC-WE001'. Off-white coloured, injection moulded PVC fitting. For use with water up to 45°C.
'LSPVC-WE001'. Off-white coloured, extruded PVC pipe. For use with water up to 45°C.
`Chemonit 181`. Black coloured, hard rubber material manufactured by roller head extrusion and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'EP2/2/4 BLK 'O' ring'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 45 IRHD. Tested in-radius size 0.9mm. For use with water up to 85°C.
'TEC N41-70 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
‘Silopren LSR 2030, 2040, 2050, 2060, 2070 & 2080’. Natural (appears clear), compression moulded silicone rubbers with a shore hardness between 30 and 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LP4411ANAT, LP37ANAT, LP4611ANAT & LP4811ANAT'. Natural (off-white coloured), compression moulded silicone rubber materials. Shore hardness 40°, 60° and 80° respectively. Tested in-radii sizes between 1.0mm and 2.0mm. For use with water up to 85°C.
'Adey MCXS Clear'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet 'issue 1' dated 03/03/2022. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikasil DW Trans'. Site applied silicone sealants available in transparent (CO0 transparent), grey (RA1 7004) or black (CO4 Schwarz). Apply as per manufacturer's instructions Product Data Sheet 'April 2022, Version 04.01'. Cure for 24 hours@7°C. The transparent (CO0 transparent) and grey (RA1 7004) sealants are for use with water up to 85°C. The black (CO4 Schwarz) sealant is for use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 28 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
