Range of plastic bodied inline, tee and angled spherical or servicing valves with EPDM ‘O’-rings. The products are either lever or screwdriver operated (see model). The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C for all models except AVT67665SM, AVT67661SM and AVT67445SM.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with bronze, brass or DZR brass bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar GVBZ25 Series = 25.0 bar Maximum working temperature: 85C
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (GVBZR20, GVBZ20 and GVBZ prefix models). Bronze body, bronze wedge and lockshield (GVBZLS16 and GVBZLS20 prefix models). Brass body, brass wedge and handwheel (GVBZ16 model only). Maximum working pressure 20.0 bar & 25.0 bar (model GVBZLS16 DN50 only). Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. Non-rising spindle, with a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, bronze bonnet, EPDM ‘O’-ring and PTFE seat. The valves are operated via a non-rising stem and a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Scale inhibitor with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
'M90-44'. Red coloured, injection moulded POM material. For use with water up to 85°C.
'WITCOAT HIGH BUILD BITUMINOUS BLACK PAINT'. Factory applied, black coloured bitumen paint. Apply as per manufacturer's TDS, dated '28.06.2025'. Cure for 72 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CY4000'. Black coloured, machined, Phenolic resin impregnated Carbon ring. For use with water up to 85°C.
'JSP/SF-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PENTALINE DI 750 BLUE'. Factory applied, two-part, blue coloured epoxy coating. Mix parts A and B in a 3:1 volume ratio and apply as per manufacturer's TDS 'Issue date: August 2023. Reference No - 01'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025-01'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Genesis FBE 5010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS issued 'August 2025'. Cure for 10 minutes@200°C. For use with water up to 23°C.
'VPC5022 Signal Blue FBE'. Factory applied, blue coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per manufacturer's Product Data Sheet 'VPC5022', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC8001 Gloss Black FBE'. Factory applied, black coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per Product Data Sheet 'VPC8001', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Factory applied, two-part, black or white polyurethane coatings. 'Pentathane 1000 SD Black'. Mix parts A & B in a 2.5:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 65°C. 'Pentathane 1000 SD Off White'. Mix parts A & B in a 3:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 23°C.
'Abcite® 1060 DW Blue & Abcite® X60 DW Blue'. Factory applied, blue coloured thermoplastic powder coatings applied by dipping in a fluidised bed. Pre-heat substrate the coating is to be applied to for 12 minutes@280°C and apply as per manufacturer’s Application Guide ‘Version 04.05.2015’ (Abcite® 1060 DW Blue) or Technical Data Sheet ‘11/2023’ (Abcite® X60 DW Blue). Post-heat for 5 minutes@160°C. For use with water up to 23°C. These materials are only approved for the pre-heat and post-heat conditions that appear on the approval. If the pre-heat and/or post-heat conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MC-PROOF 4200 AE'. Site applied, cream coloured (once mixed), two-component urethane based coating. Mix Part A (amber liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS dated 07.10.2025. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MC-PROOF 4210 AE'. Site applied, grey coloured (once mixed), two-component polyol and prepolymer based coating. Mix Part A (grey liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS '07.10.2025'. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZGC110DQ & ZGC108DQ'. Beige coloured ion exchange resins. For use with water up to 65°C.
'WL1225 Lubricant Soft Soap'. Amber coloured (translucent) lubricant. Apply as per manufacturer's IFU dated 22nd April 2025. For use with water up to 65°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'RP380s & RP361'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Berusil SM 2000'. Clear, liquid lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'RADILON® DT RV300RKC2 205 WT'. White coloured, injection moulded, glass filled Polyamide 612 material. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'SC1100UR'. Colourless, injection moulded polycarbonate material. For use with water up to 60°C.
'Menzolit SMC1000 3018-White'. White coloured, hot-press compression moulded Polyester Sheet Moulding Compound (SMC). For use with water up to 30°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 Version: 0, 19/11/2020’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JXPE100LP'. Blue coloured, extruded HDPE pipe. For use with water up to 23°C.
'SAB A16 Compression Fittings'. Black coloured, compression fitting bodies, injection moulded from polypropylene (PP-B). For use with water up to 60°C.
'TAHWEEL PPR PIPES'. Green coloured, extruded PP pipes. For use with water up to 60°C.
'TAHWEEL PPR FITTINGS'. Green coloured, injection moulded PP fittings. For use with water up to 60°C.
'HYDRO-FLO'. Green coloured (with red external stripe), extruded PPR pipe. For use with water up to 60°C.
'TAHWEEL Multi-layered PPR Pipe (Fibre Glass)'. Extruded, multi-layered pipe comprising of a green coloured inner layer, grey coloured fibre second layer, green coloured PPR third layer and black (with grey stripes) coloured PPR outer layer. For use with water up to 60°C.
'PTFE Thread Seal Tape 201 (white), 202 (pink), 203 (yellow), 204 (blue) & 205 (grey)'. PTFE tapes, manufactured by extrusion, stretching and calendaring, available in a range of colours. For use with water up to 85°C.
‘662016, 662014, 662062/SF (251VM), 662062-10PK/SF (523VM), 662061-10PK/SF (113VM)’. White coloured, PTFE tapes manufactured by calendering. For use with water up to 85°C.
Page 217 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
