Deck mounted flow control valve incorporating a brass body, quarter turn ceramic disc headwork with circular operating members and EDPM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, flow control valves (brass bodies), incorporating a quarter turn ceramic disc headwork with either a cross top or single lever operating member (see models). The products are supplied with a metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pilot operated pressure reducing control valves with ductile iron bodies (blue polyester or epoxy coating) and EPDM diaphragm. Maximum inlet pressure 25.0 bar. Outlet pressure setting is adjustable in the range of 1.0 – 16.0 bar. Maximum operating temperature 65°C.
Range of latching and non-latching solenoid valves with brass bodies and an integral stainless-steel strainer. X262513141 (abc) (dd) models have a NBR ‘O’-Ring and diaphragm, all other models have an EPDM ‘O’-Ring and diaphragm. Maximum working pressure: see model. Maximum operating temperatures: X262513141(abc)(dd) models 65°C, all other models 85°C.
Isolation elbow, incorporating brass bodies (chrome plated) and brass ball (chrome plated), EPDM O-rings and a PTFE seal. The product is supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 50°C
Angled valve (chromium plated brass body), NBR rubber seals and a dome type operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C
Range of in-line, “T” type or angled spherical valves incorporating brass bodies and brass ball, EPDM ‘O’-rings/Washers, PTFE seats and single lever or butterfly lever operating members. Some models incorporate port or pressure gauge. Models 0516/03DCVR1, 0516/03DCVR2 & 0516/04TR1 incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressures 10.0 bar Maximum operating temperature 100°C.
Range of brass bodied, straight and angled two and three-port spherical valves. Some models incorporate a screw-down pattern drain valve. Products incorporate a chrome-plated brass ball and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (nickel plated) brass bodies with single lever operating members, (chromium plated) brass ball and PTFE seat. Maximum working pressure 40.0 bar (Models 124-1027 CST, 124-1028 CST and 124-1029 CST) Maximum working pressure 25.0 bar (Models 124-1030 CST and 124-1031 CST) Maximum working pressure 16.0 bar (Models 124-1032 CST and 124-1033 CST) Maximum operating temperature 85°C.
Range of angled isolation ball valves incorporating brushed chrome plated DZR brass bodies, DZR brass ball (chrome plated), stainless steel strainer and approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of gate valves incorporating brass bodies, NBR, PTFE and fibre seals. For use with copper pipe (EN 1057) Maximum working pressure 16.0 bar. Maximum working temperature 85°C.
Range of thermostatic circulation valves incorporating brass bodies and EDPM ‘O’-rings. Some models incorporate a gauge port. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Silver and copper disinfection ion generator with a plastic body, incorporating a plastic flow switch. Maximum working pressure 9.0 bar. For cold water use only
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply as per manufacturer’s technical data sheet 'no. 786.3' dated 2013-V2'. Cure for 5 hours@23°C or 30 minutes@50°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'GMF-01'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 6070'. Factory applied, black coloured, electrodeposition coating. Apply and cure as per technical data sheet ‘LT/F-16-128’ dated October 20th 2016. For use with water up to 23°C.
'Flogul® 645 Vert 6013'. Factory applied, green coloured paint. Apply as per manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Vulkanite Bio`. Red coloured, compressed fibre gasket material. For use with water up to 65°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Ultramid® B3EG7 black 00564' (Black coloured) & 'Ultramid® B3EG7 uncolored' (appears beige). Injection moulded nylon materials. 'Ultramid® B3EG7 uncolored' is for use with water up to 65°C. 'Ultramid® B3EG7 black 00564' is for use with water up to 85°C.
'EcoPaXX® Q-DWX6 BK00002 & EcoPaXX® Q-DWX10 BK00002’ (black coloured). 'EcoPaXX® Q-DWX6 NA99001 & EcoPaXX® Q-DWX10 NA99001’ (natural – appears beige). Injection moulded polyamide materials. For use with water up to 85°C.
'Green Pipes HDPE Pipes'. Black coloured (with blue external stripe), extruded HDPE pipe. For use with water up to 65°C.
'Green Pipes HDPE Fittings'. Black coloured (with blue external stripe), fabricated butt-fusion HDPE fittings. For use with water up to 65°C.
'XD PE Fitting'. Black coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'iJoint'. Black coloured, injection moulded polypropylene fitting. For use with water up to 60°C.
'EP10/00/2 BLK EPDM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 65. Tested in-radius size 1.5mm. For use with water up to 85°C.
`TL-KN-006`. Black coloured, compression moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 1.1mm. For use with water up to 23°C.
Black coloured, compression moulded EPDM components. For use with water up to 85°C. ‘559843, 55985 & 559865’ ‘O’ rings. Shore hardness between 60 & 80. Tested in-radius sizes between 1.31mm & 3.49mm. ‘55985 Gasket’. Shore hardness 70. Tested in-radius size 1.0mm. ‘559865 gasket’. Shore hardness 80. Tested in-radius size 1.50mm. When processing an application for a Product Approval incorporating these components, these are the only shapes of components that are covered by the scope of the approval’.
'Sunaflex T 8157'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP50, EP55, EP60, EP65, EP70, EP75 & EP80'. Black coloured, transfer moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius size 1.1mm. For use with water up to 85°C.
'006800.3 washer, 006802.6 washer & 006906.4 slab (made using 7741 compound)'. Red coloured, compression moulded VMQ components. Shore hardness 70. The '006800.3 washer’ has a tested in-radius size of 1.16mm. The ‘006802.6 washer’ has a tested in-radius size of 1.15mm. The ‘006906.4 slab' has a tested in-radius size of 1.17mm. For use with water up 85°C.
'TPE-GB6061G (grey coloured) & TPE-GB6061B (blue coloured)'. Injection moulded TPE materials with a shore hardness of 60. TPE-GB6061G has a tested in-radius size of 1.41mm. TPE-GB6061B has a tested in-radius size of 1.38mm. For use with water up to 75°C.
Floor mounted single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model). The product incorporates a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose incorporates an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
A range of wall mounted two hole single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor on the underside of the tap. The inlets of the function block incorporate stainless steel strainers, plastic silencers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Page 18 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
