'LRPOLO22-ISO'. Factory applied, yellow coloured Isophthalic Polyester Resin. Apply as per manufacturer's TDS 'LRF-QAC-FM-002, Rev 02', dated '27th Dec 2022'. Cure for 24 hours@25°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431 Primer for use with HYDRALFUN AC BLEU PAM RAL5005-CZL8190 Coating’. Factory applied, dark blue coloured (once applied), powder coating for use with two-part epoxy primer. Mix parts A & B of primer in a 100:10 mass ratio and apply as per manufacturer’s TDS dated February 2024. Cure for 24 hrs at 20°C. Apply coating as per manufacturer’s TDS dated February 2024 and cure for 21 days at 20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'file no. I01-KAJ1207' dated '2019.1.14'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'OBE-5378'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instructions 'OBE-HG-001', edition 'A1', issue date '2023-OCT.-11st'. Cure for 10 minutes at 190°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2019-9-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's TDS dated '24/11/2021'. For use with water up to 85°C.
'TEFRO®cor 150SW-LV'. Grey coloured, factory applied epoxy coating. Mix in a 6:1 weight ratio (4:1 volume ratio) and apply as per manufacturer's Product Data Sheet, 'Revision Status 02/11/2023'. Cure for 7 days at 23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'18521 Kanepox Lining Free Cream or Red for use with Kanepox Hardener 0362'. Factory applied, two-part, cream or red coloured epoxy coatings consisting of component A (18521) and component B (0362). Mix and apply as per date sheet ‘Rev. No. 11’ dated February 2018. Cure for 7 days@23°C. The cream coating is for use with water up to 50°C. Between February 2024 and August 2024, the red coating is for use with water up to 23°C. From September 2024 the red coating is for use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Hempadur 3556K’. Factory applied, cream coloured epoxy coating consisting of a two-part primer and two-part top coat. The two-part primer is Hempadur 15590 red (56880) and this is mixed in a volume ratio of 7.93:2.14 and applied as per manufacturer's Product Data Sheet dated February 2024. Cure for 24 hours@20°C. The two-part top coat is Hempadur 3556K cream (20320) and this is mixed in a volume ratio of 6.8:2 and applied as per manufacturer's Product Data Sheet dated March 2024. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Hempadur 3556K’. Factory applied, cream coloured epoxy coating consisting of a two-part first coat and two-part second coat. The two-part first coat is Hempadur 3556K light red (50900) and this is mixed in a volume ratio of 6.8:2 and then cured for 24 hours@20°C. The two-part second coat is Hempadur 3556K cream (20320) and this is mixed in a volume ratio of 6.8:2 and then cured for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempaline® Defend 630 Cure 72'. Factory applied, light blue coloured, two-part epoxy phenolic coating consisting of a base and curing agent. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's Product Data Sheet dated February 2024. Cure for 6 days@20°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Raymond Microsilica Modified Cement Mortar Standard A'. Site applied, grey coloured cement mortar. Mix cement/sand in a 1:1.1 mass ratio. To this add micro silica at 7%, achieved by mixing cement mix/micro silica in a mass ratio of 1:0.07 and water at 1:0.32 (cement mix/water). Add the MasterPozzolith 55R at a ratio of 2.2ml per kilo of cement. Apply as per manufacturer’s TDS ‘TDS/RI/2024/MMCM “Standard A’, dated ‘ 21 Feb 2024’. Cure for 28 days at a temperature of between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ES 988 DWPU'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv2.17102018'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'CF 1000`. Green coloured, compressed synthetic fibre sheet material manufactured by calendaring. For use with water up to 23°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘G. BESLUX BESSIL EHV-00’. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 85°C.
'Ambersil Silicone Anti-Stick' and 'Ambersil Silicone Lubricant'. Clear liquid lubricants. Apply as per manufacturer`s instructions 'version 2.0' dated June 2018. For use with water up to 85°C
'REGZ09 - Premier Giant Silicone Spray'. Clear liquid lubricant. Apply as per manufacturer`s instructions which appear on the spray packaging. For use with water up to 85°C
'Badadur PBT9 GF10/GK20 graphit 371'. Dark grey coloured, injection moulded PBT material. For use with water up to 65°C.
'LEXAN EXL1494T-NA8A005T'. Colourless, injection moulded Polycarbonate material. For use with water up to 85°C.
'P5003D-B. Black coloured, injection moulded PE fitting. For use with water up to 23°C.
`Simona Peak Pipe Systems PE80 Pipe`. Blue coloured, extruded PE80 pipe. For use with water up to 23°C.
'Saudi Drip HDPE PE100 pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'Uponor PE 100 RC Pipe'. Black coloured (with blue external stripe), extruded PE pipe. For use with water up to 23°C.
'SCGC HDPE H1000PC'. Black coloured, extruded polyethylene material. For use with water up to 85°C.
'T-NO.100S'. White coloured (translucent) PET mesh manufactured by weaving. For use with water up to 45°C.
‘Tecotek OP20 BK014 01 0A QF, Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF’. Black coloured, injection moulded PPO/HIPS materials. Tecotek OP20 BK014 01 0A QF is an unfilled PPO/HIPS material suitable for use with water up to 23°C. Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF are filled PPO/HIPS materials suitable for use with water up to 85°C.
‘4TECH 9S20000 W-A-ABK 01 0A QF, 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK’. Black coloured, injection moulded PPO & PPO/HIPS materials. 4TECH 9S20000 W-A-ABK 01 0A QF is an unfilled PPO material suitable for use with water up to 23°C. 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK are filled PPO/HIPS materials suitable for use with water up to 85°C.
'5308400500 polypropylene liner tube', taupe coloured, injection moulded polypropylene liner. In March 2025, '5308400500 polypropylene liner tube', natural (appears beige), injection moulded polypropylene liner was added to the approval. For use with water up to 23°C.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'60EP126p'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.6mm. For use with water up to 85°C.
'EPDM 5070 Membrane'. Black coloured, compression moulded EPDM membrane. Shore hardness 58. Tested in-radius size 1.02mm. For use with water up to 85°C.
'EP703901 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EPDM-A-001'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'TT-001 Natural'. Natural (appears white, translucent), compression moulded silicone rubber material. Shore hardness 50. Tested in-radius size 0.5mm. For use with water up to 85°C.
'Guarri 543'. Blue coloured pipe sealant. Apply as per manufacturer's instructions '543 Usage', version '0', issue date '22/06/2023'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Drei Bond 5204’. Yellow coloured anaerobic adhesive paste. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
‘THERMOLAST DW’ range of natural (appears off-white), black, white & grey coloured, extruded TPE-S materials with an in-radius between 0.39mm & 0.41mm. DW7HTV-(1) (70 ShA). DW7HTU-(1) (75 ShA). DW8HTV-(1) (80 ShA). DW8HTU-(1) (85 ShA). DW9HTV-(1) (90 ShA). DW0HTV-(1) (40 ShD). (1) – indicates the colour of the material: - LCNT: means without pigment (natural colour). - 9017: means black coloured material. - 9003: means white coloured material. - 7---: 4 digit code means grey coloured material, mixture of white and black pigments. For use with water up to 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test, suitable for backflow prevention against Fluid Category 5). Maximum working pressure 7.5 bar. Cold water supply only.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted single hole, single outlet (fixed) electronically controlled tap assemblies, (chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted single hole, single outlet (fixed) electronically controlled tap assemblies, (chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically operated tap assemblies incorporating stainless-steel bodies (various finishes - see model). Flow is controlled via solenoid valve and actuated by a capacitive (TSL-881/883) or infra-red (TSL-882/884) sensor. The products can also be supplied with an additional plastic aerator (from a choice of two). Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, (fixed), electronically controlled combination tap assemblies (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar. Maximum operating temperature 70.0°C.
Side entry BS1212-4 fill valves with a plastic body. Maximum working pressure 10.0 bar. Coldwater use only.
Type ‘AB’ air gap arrangements (verified by test - suitable for backflow protection against fluid category 5) consisting of an inlet hose and solenoid valve on the inlet supply. Maximum working pressure 10.0 Bar Maximum operating temperature 55.0°C
Range of dry trap tundishes with plastic bodies incorporating a spring-loaded diaphragm on the outlet. Maximum operating temperature 85°C
Page 157 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
