‘PRIMER NATZINC EP9015 SC PART A’ Primer for use with ' HYDRALFUN AC BLEU PAM RAL5005-CZL8190 ' top-coat. Factory applied, blue coloured (once applied) primer and finish-coat. Mix base:hardener of primer in a 100:10 weight ratio and apply as per manufacturer’s TDS February 2024. Then apply top-coat as per manufacturer’s TDS February 2024. Cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempathane PW 35660 blue & off-white`. Factory applied, two-component polyurethane liquid coating consisting of a base and curing agent. Mix base and curing agent in a 3:1 volume ratio and apply as per product data sheet dated December 2023. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikagard®-180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180_05_18/v9/02_22/v10/05_23/v11/01_24'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Subcote FLP II’. Site applied, two-component, green coloured (once mixed and applied) Polyurethane coating. Mix parts A & B in a 100:72 weight ratio and apply & then flush as per manufacturer's IFU 'IFU_Subcote FLP II_In-Situ Pipes_Issue 7_210921 RS EN'. Cure for 1 hour@3°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikagard®-1814 - RAL 7035’. Site applied, grey coloured (once mixed), two-component epoxy polysulfide resin coating. Mix Part A (light grey, opaque liquid) and Part B (light yellow, translucent liquid) in a 78:22 weight ratio and apply 2 coats as per manufacturer’s TDS ‘MBS_CC-UAE/Pr_1814_06_23/v1/01_24’. Cure coat 1 for 9 hours@25°C. Cure coat 2 for 14 days@25°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Klinger K10'. White coloured, braided compression packing. For use with water up to 85°C. For use only as a gland packing material having been tested at a reduced surface area to volume ratio.
'Graphalloy Bushing Grade GM 690'. Grey coloured, resin impregnated, carbon/graphite material. For use with water up to 23°C.
'Ecoflex HT'. White coloured (translucent), extruded TPS hose. Shore hardness 88. Tested in-radius size 0.62mm. For use with water up to 85°C.
'Polimid A30GF Natural WR'. Natural (light grey coloured), injection moulded PA66 material. For use with water up to 85°C.
'Icorene 1440 NAT & Icorene 1440 BLK 9001'. Natural (appears off-white) & black, rotationally moulded polyethylene materials. For use with water up to 23°C.
'Asrene SP4808'. White coloured, compression moulded HDPE material. For use with water up to 65°C.
'GF PVC-U Metric Pipe'. Dark grey coloured, extruded u-PVC pipe. For use with water up to 60°C.
'MILGERLAN EBONITE 1065G'. Black coloured, calendered natural rubber material. Shore hardness 65. Tested in-radius size 3.1mm. For use with water up to 23°C.
'ERIKS 559706'. Black coloured, EPDM 'O' ring with a vulcanised joint, manufactured by extrusion. Shore hardness 70 ShA. Tested in-radius size 8.0mm. For use with water up to 23°C.
'EP70-S3150/B1-73898 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'3E60B11P/3E60B18P & 3E70B03P/3E70B16P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SIL7018 red & SIL7018 blue'. Red and blue coloured, compression moulded silicone rubber 'O' rings. Shore hardness 70A. Tested in-radius size 2.6mm. For use with water up to 85°C.
'LOXEAL 55-03'. Blue coloured anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions.
Range of single-hole, single outlet (fixed) electronically controlled combination tap assemblies (brass bodies – chrome plated). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating on the side of the body. The spout outlets incorporate plastic flow straighteners. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The products are supplied with single lever spherical valves. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies, (chromium plated brass body). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of side or bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of spring-loaded resilient trim in-line check valve cartridges with acetal bodies. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) over the rim swivel nozzle bidet combination tap assembly (brass body - various finishes) with a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of ¼ turn ceramic disc headworks with brass bodies, EPDM ‘O’-rings and either a red or blue silicone gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Thermostatic cartridge with NBR ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating a non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Product is supplied with a lever operated pop-up waste (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets of all models except TAP031 incorporate a plastic aerator. TAP031L Maximum working pressure - 5.0 Bar. Maximum operating temperature 85°C. All other models Maximum working pressure - 10.0 Bar. Maximum operating temperature 65.0°C
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with DZR brass adaptors for installation on each inlet. The adaptor incorporates a stainless-steel strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination taps assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure: See models. Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks and lever operating members. The spout outlet incorporates a plastic aerator. Models:11 020 xx0 & 11 025 xx0 are supplied with a lever type pop up waste kit – Not verified by test. Models 11 021 XX0 & 11 035 xx0 are supplied with permanently open waste sets – Not verified by test. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 bar Maximum operating temperature 60°C
Single hole, single outlet (fixed) combination basin tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators, flow straighteners, stainless steel strainers or open outlet type spouts (see models). Some models are supplied with a click type pop-up wastes, that have been verified by test (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Single hole, single outlet (fixed) combination tap assembly (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a ‘lever type’ pop-up waste (not verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assembly (various finishes), incorporating quarter turn (/L or /F models) or half turn (/H models) ceramic disc headworks. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies incorporating ¼ turn ceramic disc headworks and single lever type or dome operating members. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass bodies) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. All spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (gold effect plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a pull-out hose and with a plastic aerator. The product incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated), incorporating a quarter turn ceramic disc headwork which controls the water dispenser via a single lever operating members and a ceramic cartridge headwork which controls hot and cold via a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Page 149 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
