Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of servicing valves with chrome plated brass balls and brass bodies (chrome plated) with either lever operating or butterfly operating members (see models). Compression connection to be used with copper pipe EN1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of lever or butterfly operated spherical valves with brass or nickel-plated brass (CC617 and Arc89) or DZR brass bodies (CCDZR). Incorporating brass or nickel-plated brass (CC617 and Arc89 ) or DZR brass ball (CCDZR). For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball, (DZR brass body and ball on FFDZR prefix models). Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Pairs of angled spherical valves with DZR brass bodies (chrome plated), brass ball (chrome plated), stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of gate valves with DZR brass bodies, stems and discs. The valves operate via a hand wheel (non-rising) and a metal to metal seal. Valves are for above ground use only. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves with DZR brass bodies, stems and discs. The valves operate via a hand wheel (non-rising) and a metal to metal seal. Valves are for above ground use only. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
`KalGUARD` range of electrolytic scale inhibitors with chromium plated copper bodies and brass end connectors. Maximum working pressure 20.0 bar. Cold water use only.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of magnetic scale inhibitors incorporating nickel plated copper bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units, for above ground use only. Maximum operating pressure 10.0 bar. Cold water use only.
'DURACON® EX-09 WK2001' & 'EX-09 WK2001BG'. White coloured, injection moulded acetal materials. For use with water up to 85°C.
'CD 101 Grey Sealing Disc'. Grey coloured ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'Rubalit A1896 Sealing Disc'. White coloured ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'APCOSHIELD FBVL EX400G – RAL 5005 Blue & RAL 5017 Blue'. Factory applied, blue coloured epoxy coatings. Apply as per manufacturer’s datasheet ‘PDS/APPPG/V01/01-2024’. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBPC EX405SG INTER GREEN'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's data sheet 'PDS/APPPG/V02/01-2024'. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotun Marathon IQ2'. Factory applied, two-component, grey coloured epoxy coating. Mix parts A:B in a ratio of 3:1 parts and apply as per 'Jotun Marathon IQ2' Technical Data Sheet dated '16 April 2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI Hygienic CML'. Factory applied, grey coloured cement mortar. Mix cement mortar:sand:water in a weight ratio of 36:46:18 and apply as per manufacturer's instructions 'LMICMA012624', dated '1/26/2024'. Cure for 20 hours@40°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Alsen FBE Blue Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'AIPL 1212/1', dated '07/06/2023'. Cure for 2.5 hours:235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSC-01'. Factory applied, grey coloured cement mortar. Mix sand:water: cement in a 1.5:1.0:1.0 weight ratio and apply as per manufacturer's instructions 'GB0012023', edition 'A1'. dated '2023-10-10'. Cure for 24 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBERPOX-2K-DS-LACKFARBE (IV81 & IW81)’ – blue coloured and ‘LUBERPOX-2K-DS-LACKFARBE (IV81812 & IW81)’ – red coloured’. Factory applied, two component, epoxy coatings consisting of IV81 or IV81812 (base) and IW81 (hardener). Mix IV81 or IV81812 (base) & IW81 (hardener) in a mass ratio of 5:1 or volume ratio of 3.5:1 and apply as per manufacturer’s data sheets ‘Rev: 04 – 04.12.2023’ (blue) or ‘Rev: 03 – 04.12.2023’ (red). Cure for 20 minutes@22°C and then 40 minutes@75°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JBG-SRPC Plus'. Factory applied, sulphate resisting Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JBG-OPC Plus'. Factory applied, grey coloured, ordinary Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DIMERSIL 10`. Green coloured, compressed synthetic fibre sheet material manufactured by calendaring. For use with water up to 23°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Flexseal 163 Green`. Green coloured, compressed synthetic fibre sheet material manufactured by calendaring. For use with water up to 23°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'CF 1000`. Green coloured, compressed synthetic fibre sheet material manufactured by calendaring. For use with water up to 23°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Badadur PBT9 GF10/GK20 TM-Z1 grau 930a'. Grey coloured, injection moulded polybutylene terephthalate material. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 grau 930a'. Grey coloured, injection moulded PBT material. For use with water up to 85°C.
'LEXAN EXL1494T-NA8A005T'. Colourless, injection moulded Polycarbonate material. For use with water up to 85°C.
'Cosmoplast HDPE Pressure Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 65°C.
'PIMTAS PLASTIK PE 100 Pipes'. Extruded, PE100 pipes available in black and blue colours. For use with water up to 85°C.
'SCGC HDPE H1000PC'. Black coloured, extruded polyethylene material. For use with water up to 85°C.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WRAS 61813 E80'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 2.2mm. For use with water up to 60°C.
'60EP126p'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.6mm. For use with water up to 85°C.
'E59WKZ'. Black coloured, injection moulded EPDM rubber material. Shore hardness 58. Tested in-radius 1.0mm. For use with water up to 60°C.
'HT5557-10'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. Between January 2024 and March 2024, the material was for use with water up to 50°C. From April 2024 the material is for use with water up to 60°C.
'WN12/7/1 BLK 'O'-rings'. Black coloured, injection moulded NBR 'O' rings. Tested in-radii sizes between 0.89mm and 2.0mm. Shore hardness 70. For use with water up to 65°C.
'10' range of extruded, silicone rubber material available in translucent (which appears off-white), black, white, red and blue colours. Shore hardness between 40 & 70. Tested in-radii sizes between 0.15mm & 6.0mm. For use with water up to 85°C. A full list of the individual product codes included on this approval is available from WRAS.
‘CORE® Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.2’, dated 12/01/23 and this material is only approved for these conditions. For use with water up to 85°C.
Page 123 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
