'Guom-07'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a weight ratio of 1:1.5:0.6 and apply as per manufacturer's User Instructions 'GUOM-24', 'Vision: B', dated '2024-11-5'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MAVM554'. Factory applied, blue coloured, epoxy powder coating. Apply as per manufacturer's data sheet 'FR.07.03.18', dated 09.19. Cure for 10 minutes at 160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Solvent Free Epoxy Coating XH4205'. Factory applied, white coloured, two-component epoxy coating. Mix Coat 1 (XH4205/grey coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 24 hours@25°C. Mix Coat 2 (XH4205/white coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue & Green. Factory applied, green or blue coloured epoxy coatings (manufactured in Dammam, Saudi Arabia). Apply as per manufacturer's MTI '001 - 2024 - SA – EN'. Cure for 4 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electroline ES 424'. Factory applied, white coloured, two-component epoxy coating. Mix Part A and Part B in a volume ratio of 2:1 and apply as per manufacturer's TDS 'ECL/ TDS / ES424', version '0', dated '05.01.2024'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat Epoxy Blue Patch Up Paint (PFC/1017)'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:2 volume ratio and apply as per manufacturer's IFU 'DOC/PFC/PU/101', dated '01.04.2024'. Cure for 8 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`MECH WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions '24136' dated 2025/1/26. For use with water up to 85°C.
'EM6/35/7541/1'. Factory applied, dark blue coloured Porcelain (vitreous) enamel coating. Apply as per manufacturer's instructions 'IS_003', 'rev. 01'. Cure for 16 min 875°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carboguard AQP FC Part A and Part B'. Site applied, grey coloured (once applied) epoxy coating. Mix Parts A & B in a weight ratio of 1:1 and apply as per manufacturer's Product Data Sheet '8163', dated 'March 2025'. Cure Coat 1 for 24 hours at 20°C and Coat 2 for 7 days at 20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monoflex W'. Grey coloured, extruded TPO 'tape'. Shore hardness 91. Tested in-radius size between 0.45mm & 1.0mm. For use with water up to 70°C.
'7740 WPG'. White coloured, silicone based lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'RPL-104'. Off-white coloured, unsaturated polyester resin material, manufactured by hand lay up process. Between March 2025 and March 2026, the material was for use with water up to 23°C. Between April 2026 and March 2030, the material is for use with water up to 50°C.
'R579 TP13582 BLACK & R579 TP14619 BLACK'. Black coloured, rotomoulded PE materials. For use with water up to 85°C.
'Fortron® 1130T4 SD3039 Black'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Hostalen PP H2142 12'. Black coloured, injection moulded and compression moulded polypropylene material. For use with water up to 23°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Benvic IR745AB/9738' & 'IR712AB/9738'. Grey coloured (opaque), compression moulded PVC materials. For use with water up to 23°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (chromium plated brass). The flow is controlled via solenoid valve which is actuated by an infra-red sensor. The temperature for the 107.6917, 107.6918 and 107.5608 models is controlled independently via a single lever operating member. The inlets of the 107.6917, 107.6918 and 107.5608 models (main body) incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the 107.6917 and 107.6918 models (main body) incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The 107.5601, 107.5602 and 107.5608 models have an integral soap dispenser (separate to the water pathway). The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass body). Incorporating quarter turn ceramic disc headworks, dome type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FLKIT40 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT60 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT80 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
Spring loaded, resilient trim, in-line check valve cartridges with plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim check valve cartridge with plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of assisted bathing units. The flow is controlled via an electronic thermostatic mixing valve which can feed either a bath spout outlet or shower handset. The discharge from both the bath spout and shower handset are via a type AUK 3 airgap, verified by measurement, suitable for fluid category 5 backflow protection. These bathing units have adjustable height and tilt functions. Maximum working pressure 6.0 Bar Maximum operating temperature 45.0°C
Range of either half turn, quarter turn ceramic disc or non-rising spindle headworks with brass bodies and EPDM ‘O’ rings. For insertion into specifically dimensioned bores. Maximum working pressure 20.0 Bar Maximum operating temperature 90.0°C
Range of ceramic cartridge headworks with plastic bodies, incorporating EPDM seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar (D40P-17 & D40G-17) or 20.0 Bar (D25G-6) Maximum operating temperature 85.0°C
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of ceramic cartridge and 2-way ceramic disc diverter headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with either stainless steel (models 49xxS604WF & 49xxP704WF only) or brass (all other models) bodies (various finishes). The products incorporate a ceramic cartridge headwork with either single lever, cylindrical or no supplied operating members (see models). The spout outlets incorporate a plastic aerator and model 58xxL904F is supplied with a lever operated pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 80°C.
Range of single hole, single outlet combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) bodies, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with a click type pop-up waste (not verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) bodies, incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. Products are supplied with click type pop-up wastes (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) bodies, incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a click type pop-up waste (not verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes), incorporating non-rising spindle headworks and single lever or dome type operating members. The spout outlet incorporates a plastic aerator. Supplied with a lever type pop up waste – not tested. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Models 6500H/W & 6504/W are supplied with a click type waste – not verified by test. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Floor standing, single hole, single outlet (swivel) combination tap assembly with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A deck mounted two hole, single outlet (fixed) combination tap assembly, with a brass body (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with metal back nuts and plastic aerators. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 223206 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 85 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : without suffix indicates no handle / different handle option – A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| H64DMT2 | Chrome | 15mm | 10 bar | 60 °C | Bristan | Handle | No | Single sequential | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 223205 X XXX | VARIOUS | 3/4” BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : without suffix indicates no handle / different handle – A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Page 98 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
