'Fortron® 1130T4 SD3039 Black'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'Dalcon 001'. White coloured, compression moulded or extruded PTFE material. For use with water up to 85°C.
'RVK EPDM-LJHY'. Black coloured, compression moulded gaskets. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'51M7568'. Black coloured, injection moulded EPDM material. Shore hardness 75 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AA7BCZ'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'NE7130-XT'. White coloured (translucent), injection moulded Silicone rubber. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Cyberbond® SH27'. Yellow coloured (translucent) anaerobic adhesive. Apply as per manufacturer's TDS 'V01.005.en-gb.001'. For use with water up to 23°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'WS27TF Pipeseal'. Yellow coloured anaerobic adhesive. Apply as per manufacturer's datasheet issue '1.0'. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Vyncolit BXE650W'. Black coloured, injection moulded phenolic material. For use with water up to 85°C.
'JFD-PVCR01'. Beige coloured, extruded PVC pipe liner. For use with water up to 23°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass body). Incorporating quarter turn ceramic disc headworks, dome type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
Page 547 of 556
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
