'SPS HDPE Pipe'. Black coloured (with blue stripes), extruded PE 100 pipe. For use with water up to 85°C.
'SAPPCO PE100 Black Pipe'. Black coloured, extruded polyethylene pipe which has blue stripes on the outside. For use with water up to 65°C.
'BorSafe ME3440 (black)'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'BorSafe HE3490-LSH'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
`Icorene 3560 Black 9001`. Black coloured, LLDPE material manufactured by rotomoulding. For use with water up to 85°C.
‘Lubricomp OFL36A-BK1B639 & Thermocomp OF008A-BK1B636’. Black coloured, injection moulded polyphenylene sulphide materials. For use with water up to 85°C.
'DIC.PPS Z-230-T3 BLACK'. 'DIC.PPS Z-230-T3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Komaki (Japan), Penang (Malaysia). For use with water up to 85°C.
‘Wouper EG30WF, EG40WF & EG50WF’. Injection moulded, glass filled (30% - 50%) PPA materials available in natural (appears off-white), black and grey. ‘Wouper EG30WF, EG40WF & EG50WF’ natural, black & grey are for use with water up to 85°C. ‘Wouper AG30WF’. Injection moulded, glass filled (30%) PPA materials available in natural (appears off-white), black & grey. ‘Wouper AG30WF’ natural & black are for use with water up to 85°C. Between July 2022 and January 2023, ‘Wouper AG30WF’ grey is for use with water up to 23°C. From February 2023, ‘Wouper AG30WF’ grey is for use with water up to 85°C.
'Helisystem'. Green coloured (with red stripe), extruded PPR pipe. For use with water up to 70°C.
'Romafaser'. Green coloured (with blue stripe), extruded PPR & glass fibre pipe. For use with water up to 70°C.
‘Ramofin PPH300G6NT’, Natural (appears cream in colour), injection moulded, polypropylene material. For use with water up to 85°C.
'CordFlon R10D05'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'Twineflon® R12D06'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'R08D03'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'R15D08'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'LIP/PTFE/875'. Site applied, pre-mixed, injectable PTFE/Silicone Grease sealing compound. Extrude and apply the pre-mixed compounds as per manufacturer's work instructions document 'STS-MS-001', revision '01', dated 11/08/23. No cure required. For use with water up to 23°C.
'REGJ01'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'TCM585RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '21.07.2021'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-VE’. Site applied, two part, grey coloured anchor resin. 2KPS EASF-VE is light grey coloured when mixed and consists of Part A (shiny grey coloured liquid) & Part B (shiny off-white coloured liquid). Mix, apply and cure as per manufacturer’s product information sheet 'EASF-V / VC / VE (EU07) V4.0'. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'XGM050'. Black coloured, compression moulded EPDM rubber gaskets manufactured from raw material '70802'. Shore hardness 80. Tested in-radius size 2.5mm. For use with water up to 85°C.
'4360 'O' rings, washers, membranes and lip seals'. Black coloured, injection moulded EPDM components with a shore hardness of 60. The ‘O’ rings have a tested in-radius size of 1.31mm. The washers have a tested in-radius size of 1.05mm. The membranes have a tested in-radius size of 1.55mm. The lip seals have a tested in-radius size of 0.40mm. For use with water up to 85°C.
'7EP1197 Gasket'. Black coloured, extruded EPDM gasket. Shore hardness 70. Tested in-radius size 0.5mm. '7EP1197 'O'-rings' were added to the approval in March 2023. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'EP01961PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CVE78'. Black coloured, extruded EPDM material. Shore hardness 80. Tested in-radius size 10.0mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPH-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘KRE 60 (103), KRE 65 (100) & KRE 65 (106)’. In September 2022 ‘KRE 60 (104)’ was added to the approval. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60 & 65. Tested in-radius size 1.0mm. For use with water up to 60°C.
'TIMO 3-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EX60LC, EX70LC & EX80LC'. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60, 70 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'SL70L41F'. Blue coloured, compression moulded silicone rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'Addisil 2050E, 2060E, 2070E & 2080E'. Unpigmented (appear white, translucent), extruded silicone rubber materials. Shore hardness between 50 & 80. Tested in-radius size of 2.1mm. For use with water up to 85°C.
'Permabond ET5365'. Site applied, grey coloured, two-component epoxy adhesive consisting of part A (light grey coloured paste) & part B (dark grey coloured paste). The product cartridge is heated to 30°C and the two-components are mixed in a 2:1 volume ratio. Apply as per manufacturer's TDS 'revision 1', dated 23 May 2018. Cure 24 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interflon Paste HT1200'. Cream coloured ceramic paste. Apply as per manufacturer's instructions, document number 'IFUHT1200' dated 24/04/2017. Cure for 5 minutes@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VRSY6090 + Nylon 6.6 Rubber Expansion Joint'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
'ERV-R & ERP Rubber Expansion Joints'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. The `ERV-R` joint has a red coloured band on the exterior and the `ERP` joint has a red coloured dot on the exterior. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of pressurisation units with flow controlled by a float operated valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate stainless steel strainers, flow restrictors and spherical isolation valves. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16 Bar. Maximum operating temperature 65°C
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
‘Bubblestream’ range of tap outlet (stream shaper) adaptors incorporating a swivel mechanism and a stainless steel mesh aerator. All models, apart from 07.9870.0, are supplied with a M22 to M24 adaptor. All models, apart from 07.9870.0 & 07.9880.0, incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating a ceramic cartridge headworks with single lever operating members and a pull-out spray spout. The outlet incorporates a plastic aerator and single check valve cartridge however the product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single-hole, single outlet (swivel) combination tap assembly with brass body (chrome plated), incorporating a ceramic cartridge headwork with a single lever operating member. The product has a pull-out spray outlet which incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The cold inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with either a single lever or dome type operating member (see model). The spout outlet incorporates a plastic aerator (specific models only - see model section). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with either a single lever, cross top or dome type operating member (see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a waterfall type with or without a stainless-steel mesh (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 53 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
