Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with bronze bodies, PTFE seals and chromium plated brass ball. Maximum working pressure 20.0 bar. Maximum operating temperature 99°C.
Range of lever operated spherical valves with DZR brass (286W range) or nickel plated brass (289 range) bodies, chromium plated brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar (286W range), 40.0 bar (289 range). Maximum operating temperature 85°C (286W range), 99°C (289 range).
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass or DZR brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, non-rising spindles with handwheel operating member and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Cold water use only. From Jan 2025 maximum operating temperature 50°C, for models marked "WRAS - 50 DEGREES" on adhesive label on bonnet.
Range of UV water treatment units with stainless steel bodies and quartz sleeves. Maximum operating pressure 8.6 bar. Cold water use only.
'PT3294 Ceramic Disc'. White coloured, compression moulded ceramic disc. For use with water up to 85°C.
'Corro Coat EP-F 5001'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's technical data sheet dated '24 September 2021'. Cure for 2.5 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 Red & Pentaline 1000 Grey'. Factory applied, red and grey coloured, two component solventless epoxy coatings. Mix component A & B in a volume ratio of 3:1 and apply as per manufacturer's document number 'Chembur R&D/PI/05', issue date '03/04/2023'. Cure for 7 days@30°C. 'Pentaline 1000 Red' is for use with water up to 45°C. 'Pentaline 1000 Grey' is for use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB50 Black Waterborne Pipe Anticorrosive Paint'. Factory applied, black coloured polyacrylate coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEP50 Black Waterborne Epoxy Pipe Anticorrosive Paint'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'3011 Red Epoxy Anticorrosive Coating'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's instructions '004', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5015 Blue Epoxy Anticorrosive Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 Blue Waterborne Pipe Anti-Corrosive Paint'. Factory applied, blue coloured polyacrylate paint. Apply as per manufacturer's TDS/IFU '001', 'First Edition', dated '2021.12.12'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-029 Waterborne Anticorrosive Coating'. Factory applied, black coloured acrylic modified resin coating. Apply as per manufacturer's Instructions for Users 'version 2.00', updated '11/01/2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FLOGUL 645B Bleu 5005'. Factory applied, blue coloured synthetic resin coating. Apply as per manufacturer's Technical Data Sheet, version '26/01/2023'. Cure for 7 days@20°C. For use with water up to 23°C.
'Xypex Concentrate'. Site applied, grey coloured, cementitious coating. Mix 'Xypex Concentrate' with water in a 5:2 ratio and apply as per manufacturer's datasheet 'DAT-CON-UK, REV-06-21'. Cure for 3 days@7°C in damp conditions, following by 18 days@7°C. Please note that 1 day cure = 24 hours. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CPT CML Variation No.2 cementitious mortar’ for use with ‘Conplast RP264 Admixture'. Site applied, grey coloured (once mixed) cementitious mortar and admixture. 'CPT CML Variation No.2 cementitious mortar’ comprises of cement, sand and Microsilica. Mix cement and sand dry in a 1:1.1 mass ratio. Add the microsilica in a 1:0.05 mass ratio with the cement content. Add water in a cement/water mass ratio of 1:0.32. Add the admixture in an admixture/ cement ratio of 8ml:1000g. Mix rigorously until an even consistency is achieved and apply as per manufacturer’s instructions reference ‘2328’, dated 13/01/2023. Cure for 28 days@ between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Mega Fix IT PW'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's label instructions ‘00000765 Mega Fix-IT PW (MULTI Product Label) v3u.indd 16/05/19’. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Atlac 430'. Yellow coloured, vinyl ester resin material manufactured by filament winding. For use with water up to 60°C.
'Inoflon® GN7040 & Inoflon® MGN7045'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
‘TWK7534, TWK5810, TWK5811, TWK5812, TWK5813, TWK5814, TWK5815’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'4711'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'Spray SLC STD Inlay 24' & 'Spray SLC STD Inlay 16 Low'. Grey coloured, injection moulded, liquid silicone rubber components. Shore hardness 70. Tested in-radius size 0.44mm. For use with water up to 70°C.
'Weld-On 724 C-PVC Grey Solvent Cement' Grey coloured solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 719 PVCu Clear Solvent Cement'. Clear, colourless solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C(±2°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maritex Aquapure Grade 5742'. Beige coloured tube manufactured by winding PET fibre and epoxy vinylester resin over a mandrel under heat and pressure, intended for the manufacture of bearings. For use with water up to 23°C.
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with chromium plated brass bodies. The flow is controlled by a solenoid valve activated via an infra-red sensor and a manually adjustable temperature lever. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of side and bottom entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of high and low level BS EN 14055 (2018) WC cisterns incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush or mono flush syphon for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres.. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
Range of spring loaded resilient trim check valve cartridges with acetal body and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of tundishes with plastic bodies. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of one piece water storage cisterns with a screened breather and over flow. Model 46714 iBoost+200 has a rectangular weir overflow Model 46712 iBoost+200 has a circular overflow Cold water only.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Product is supplied with a lever operated pop-up waste Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of self-closing headworks with stainless steel bodies to be housed in specifically dimensioned bodies. Maximum working pressure 8.8 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headwork with plastic bodied and EPDM ‘O’ rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of quarter turn ceramic disc and ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Thermostatic cartridge with a brass body and EDPM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of thermostatic cartridges with brass or plastic bodies (see model) incorporating a stainless-steel strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar. Temperature: 75°C – GR-FX-X05S, GR-FX-01S, GR-FX-13T & GR-FX-X08. 65°C - GR-FX-04S & GR-FX-02TF.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating ceramic cartridge headworks with single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers. Models ZA1147(ZA1147-G, ZA1147-S) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet is a pull-out spray type. The spout inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow prevention. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks or ceramic disk headworks (model 152108) with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model 152308 is only supplied with an aerator) . The products are supplied with a click type pop-up waste. 152108 and 179428 maximum working pressure 10.0 bar. 152038, 143338 and 179438 maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet combination tap assembly with brass bodies (chrome plated), incorporating ceramic cartridge headwork and single lever operating members. Spouts incorporate a plastic aerator. Model 3326530L is supplied with a lever-operated pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating ceramic disk headworks and single lever operating member. Spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 48 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
