‘V-PET#1600 Gray F’. Factory applied, dark grey coloured epoxy resin powder coating. Apply as per manufacturer’s instructions ‘ref.no. VP1600-PD-170412’, dated '12th April 2017'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 High chlorinated polyethylene anticorrosive coating'. Factory applied, blue coloured polyethylene coating. Apply as per manufacturer's TDS/IFU number '001', dated '2022.11.30'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Factory applied, grey coloured blast furnace slag cements. ‘BFSC PAM MDN 1’. Mix water, sand, admixture & cement in a mass ratio of 0.33:2.35:0.0080:1 and apply as per manufacturer’s instructions ‘CE 7M’, dated ‘25/08/15’. Cure for 7 hours@70°C. For use with water up to 60°C. BFSC PAM GDN 1’. Mix water, sand, admixture & cement in a mass ratio of 0.33:2.84:0.0065:1 and apply as per manufacturer’s instructions ‘CE 8M/-3A’, dated ‘25/08/15’. Cure for 7 hours@70°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Titanseal 989'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's application instructions dated '09.03.2018'. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘PULRON 101 AQUA’. Factory applied, green coloured polyethylene coating. Apply a single coat (200μm thickness) as per manufacturer's instructions 'ELS.TT.C01.40', 'Rev00', dated '13.06.2023', Cure for 10 minutes at 200°C. Between June 2023 and December 2024, the material was for use with water up to 23°C. Between January 2025 and June 2028, the material is for use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Non-metallic materials and components comply with BS6920 at 65°C°C
'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`EcoZmart Waterproofing`. Site applied, grey coloured tanking slurry. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 1 as per manufacturer's IFU 'TCOWP001', dated '26/05/2023'. Cure for 24 hours@7°C. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 2, 24 hours after the first coat, as per manufacturer's IFU IFU 'TCOWP001', dated '26/05/2023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Al Muftah Sectional Tank Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 23°C. From April 2024 the panel is for use with water up to 50°C.
'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.
'GPB2, GPB3, GPB4 & GPB6'. White coloured, liquid lubricants. For use with water up to 85°C.
‘RADISTRONG® AROMA RV400RKC2 106 NT, RV500RKC2 106 NT & RV600RKC2 106 NT’. ‘RADISTRONG® AROMA RV400RKC2 306 BK, RV500RKC2 306 BK & RV600RKC2 306 BK’. ‘RADISTRONG® AROMA RV300RKC2 106 NT’ & ‘RADISTRONG® AROMA RV300RKC2 306 BK’ were added to the approval in February 2024. Natural (indicated by NT - appear cream in colour) and black coloured (indicated by BK), injection moulded, glass fibre filled (between 30% & 60%), PA66 materials. For use with water up to 85°C.
'NADIR PLUS HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 40°C.
'NADIR PLUS HDPE Pipe'. Black coloured (with blue external stripe), extruded HDPE pipe. For use with water up to 40°C.
‘Sikaplan® WT 4220-15 C & Sikaplan® WT 4220-18 H’. ‘Sikaplan® WT 4220-15’ is a light blue coloured, extruded multi-layer polyethylene sheet material comprising of glass fibre inlay between two polyethylene sheet layers. ‘Sikaplan® WT 4220-18 H’ is a light blue coloured, extruded polyethylene sheet material. For use with water up to 60°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
''Teflon® PFA 340 X, 345 X, 350 X, 350-T-J, 440 HP X, 445 HP X, 450 HP X & 416 HP X'. Unpigmented (white coloured), compression moulded PFA materials. For use with water up to 85°C.
'Teflon® PTFE 640XT X, 807N X, NXT 70, NXT 75, 6CN X, 62 X, 62N X, 62XT X, 669N X, 669 X, NXT 85, 605XT X, 6C X, 7A X, 641XT X & 650XT X’. White coloured, extruded or compression moulded PTFE material. For use with water up to 85°C.
'24410001 & 24410002'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
'E7001Z59 (EP02269PF) 2x modified'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 72 A. Tested in-radii sizes between 1.4mm & 1.8mm. For use with water up to 85°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
'EPNER-4665'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 50°C.
'EIW-54'. Black coloured, injection moulded EPDM material. Shore hardness 51 ShA. Tested in-radius size 0.5mm. For use with water up to 50°C.
'Liner Code 'W' (for Butterfly Valves R480/R481/R487 & R488)'. Black coloured, compression moulded EPDM material with a shore hardness of 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'E134-B85-KTW-W270'. Black coloured, compression moulded EPDM material with a shore hardness of 88. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Z440'. Black coloured, compression moulded FKM 'O' ring. Shore hardness 70. Tested in-radius size 5.0mm. For use with water up to 85°C.
‘2061 VMQ 60’, red coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 60. ‘2172 VMQ 70’, blue coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 70. O-rings have a tested in-radius of 2.0mm Washers have a tested in-radius of 2.5mm. Lip seals have a tested in-radius of 0.45mm For use with water up to 85°C.
‘SIL4008F, SIL4008F (N), SIL4008F (H), SIL4008F (R) & SIL4008F (BK). SIL4508F. SIL5008F, SIL5008F (H), SIL5008F (R) SIL5008F (BK), SIL5008F (B). SIL5508F. SIL6008F, SIL6008F (N), SIL6008F (H), SIL6008F (R), SIL6008F (BK). SIL6508F. S7008F, S7008F (N), S7008F (H), S7008F (R), S7008F (BK), SIL7118F, SIL7018F. SIL7508F. SIL8008F, SIL8008F (N), SIL8008F (H), SIL8008F (R), SIL8008F (BK)’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
‘SIL40X02, SIL45X02, SIL50X02, SIL55X02, SIL60X02, SIL65X02, SIL75X02 & SIL80X02’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘SIL70B02’ – Blue coloured. ‘SIL70W01’ – Natural. ‘SIL70R01’ – Red coloured. ‘SIL7001’ – Black coloured. Range of compression moulded, silicone rubber `O` rings and gaskets available in colours listed above. Shore hardness 70. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
'EMS Force 5543'. 'EMS Force 5543-P' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '07/03/2016'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'THAT RAPID BLU-STUFF'. 'THAT RAPID BLU-GEL' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '18/05/2023'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
3-in1 single hole, single outlet (swivel) combination tap assembly (chromium plated or brushed stainless steel PVD brass). The cold//hot/mixed water circuit incorporates a ceramic cartridge headwork with a single lever operating member. The near boiling water circuit incorporates a quarter turn ceramic disc headwork with a single lever operating member. The tap is supplied with a stainless steel braided PEX lined flexible hose assembly, brass adaptor incorporating a plastic flow regulator, NBR washer and plastic adaptor to connect the tap to the near boiling water unit (not supplied) and a PTFE or silicone (from September 2024) flexible pipe to deliver near boiling water back to the tap. The spout outlet incorporates a plastic aerator, which includes a central stainless steel tube insert throughout the near boiling water outlet of the aerator. Maximum working pressure 10.0 bar. Maximum operating temperatures: 65°C (cold/hot/mixed water circuit). 99°C (near boiling water circuit after boiler unit, cold supply only prior to boiler unit).
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and a manual lever to control the outlet temperature. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Temperature:60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, electronically operated, combination tap assemblies (stainless steel body, various finishes - see model), comprising of a Premix control unit and a spout. The flow is controlled by a solenoid valve, (Premix control unit), which is actuated via an infrared sensor. The central section of the valve incorporates a plastic strainer. Both inlets of the Premix control unit incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Electronically operated combination tap assembly, (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor on the spout. The spout outlet incorporates a plastic aerator. The product is supplied with a stainless steel braided (EPDM or PEX lined) flexible connecting hose. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Range of ceramic cartridges with plastic bodies, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating either quarter turn ceramic disc or quarter turn compression washer headworks with various operating members (see model). The inlets of the quarter turn ceramic disc headworks incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model). The product is supplied with metal backnuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc or a quarter turn compression washer headwork with various operating members (see model). The inlet of the quarter turn ceramic disc headwork incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model). The product is supplied with metal backnuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating ceramic cartridge headworks with single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers. Models 5059340452869 have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated) and pull-out spray. The products incorporate a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed), combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever type pop up waste. Model (71252xxx) supplied with click type pop-up waste (not verified by test). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, single hole, single outlet fixed combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self- cancelling diverter to shower outlet. This spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly (brass bodies - chrome finish), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes) incorporating quarter turn ceramic disc or ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 BAR
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination taps assemblies (brass bodies - in various finishes), incorporating ceramic cartridge headworks with various operating members. The spout outlets incorporate plastic aerators. The inlet of the spout outlets incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Page 46 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
