Range of handwheel operated butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals. Maximum working pressure 10.0 or 16.0 bar (see model). Maximum operating temperature 65°C.
Range of combined pre-set temperature and pressure relief valves incorporating Bronze bodies, DZR brass seat and plunger, EPDM ‘O’-rings, PTFE seal and silicone diaphragm. The valves incorporate a manually operated lever easing gear. The valves are factory pre-set between 0.4 bar and 12.5 bar. Maximum operating temperature 90°C.
Concealed 2-way or 3-way ceramic disc diverter valve with shut off mechanism incorporating a brass body. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of wall mounted flow control valves and trim kits (various finishes) with brass bodies incorporating a quarter turn ceramic disc headwork with various operating members (see model). The outlet of all models, except for the 38 882 xxx AXOR Uno model, incorporates a single check valve cartridge, (verified by test suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of concealed flow control valves with a brass body and trim set (various finishes). The product incorporates a ceramic disc headwork with a single lever operating member divertering the flow between 2 shower outlets or a bath spout outlet. The diverter has an off position as you change between each outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted flow control valves with brass bodies (chrome plated trim sets and various operating members - see models) incorporating quarter turn ceramic disc headworks. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of flow control valves incorporating brass bodies, quarter turn ceramic disc headworks and NBR ‘O’-rings. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of spring loaded, resilient trim, non-return valves (blue epoxy coated cast iron body), with bronze bushing, stainlesss steel spring and disc, and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return, swing gate valves with blue epoxy coated ductile iron bodies and EPDM rubber seals. Maximum working pressure 10.0 or 16.0 bar (see model). Maximum operating temperature 65°C.
ART 388 Range of non return valves with brass bodies and discs, and EPDM washer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line adjustable pressure reducing valves with Nickel plated DZR brass bodies and EPDM gaskets. Maximum inlet supply pressure 16.0 bar. Outlet pressure in the range of 0.5 bar to 6.0 bar. Maximum operating temperature 80°C.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM seat washers & ‘o’ rings and stainless-steel filters. Various models supplied with pressure gauge (please see model list). Maximum inlet supply pressure 16.0 bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of in-line, manually adjustable pressure reducing valves with blue epoxy coated ductile iron bodies and EPDM gaskets and ‘O’-rings (all models) and an EPDM diaphragm (VRCD-M models only). VRCD models: Outlet pressure range: 1.5 - 6.0 bar or 5.0 to 12.0 bar. VRCD-M models: Outlet pressure range: 1.5 - 6.0 bar. Maximum supply pressure 16.0 bar. Cold water use only.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM seat washers & ‘o’ rings and stainless-steel filters. Various models supplied with pressure gauge (please see model list). Maximum inlet supply pressure 16.0 bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of pressure relief valves incorporating brass bodies and EPDM rubber washers. The valves incorporate a manually operated rotational easing gear. For maximum working pressure please refer to model. Maximum operating temperature 99°C.
Range of latching solenoid valves with brass bodies and EPDM diaphragm Maximum working pressure 13.0 bar. Maximum operating temperature 55°C.
A range of normally closed servo-assisted diaphragm solenoid valves with brass bodies and EDPM diaphragms. Models 23C, 23D, 23E & 23F have a maximum working pressure of 16.0 bar. Models 23G, 23H & 23I have a maximum working pressure of 10.0 bar. Cold water use only
Solenoid valves with a plastic body and silicone diaphragm and ‘O’ rings. Maximum working pressure 8.0 bar. Cold water use only.
Range of normally closed solenoid valves with a plastic body and silicone rubber diaphragm & ‘O’-rings. Models ending ‘007’ have a maximum working pressure of 0.25 bar. All other models have a maximum working pressure of 0.06 bar. Maximum operating temperature 90°C.
Range of bistable (all models) or monostable/normally closed (19.00x.287 only) solenoid valves with either a plastic body (19.00X.287) or plastic internal body with stainless steel threaded casing (50.005.102 and 50.005.(050) models) with EPDM diaphragms and ‘O’-rings. Maximum working pressures: 50.005.(050) model: 8.0 bar. All other models: 10.0 bar. Maximum operating temperature 70°C
Range of spherical valves with nickel plated DZR brass bodies with either red or blue, lever or butterfly operating member, brass ball and PTFE seat. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 bar. (Cold water use only).
Range of DZR brass gate valves incorporating brass wedges. The Fig 30 range incorporates hand wheel operating members. The Fig 30LS range incorporates a lock shield operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of stop valves incorporating brass bodies (brass or chrome plated) with EPDM ‘O’-rings and gaskets. Maximum working pressure 10.0 bar. Cold water use only.
Range of undercounter or deck mounted drinking water fountains which dispense ambient and/or chilled water. Flow is controlled via a solenoid valve and the products are activated via a push button or infa-red sensor . Maximum working pressure 7.0 bar. Cold water use only.
'KEPITAL F10-52H Blue'. Blue coloured, injection moulded POM material. For use with water up to 40°C.
'Toyolac 700-314'. Beige coloured, injection moulded ABS material. For use with water up to 23°C.
'D-1375-077'. Grey coloured, resin impregnated carbon graphite washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'H-3500-6351-9221'. Grey coloured silicon carbide washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'JIZJ-1'. Factory applied, light grey coloured Portland cement mortar. Mix cement, sand and water in a ratio of 1:1.7:0.55. Cure for 5 hours and 30 minutes@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HSXX CM-1'. Factory applied, grey coloured cement mortar. Mix, apply and cure as per manufacturer's Technical Data Sheet issue number '001' dated '2020.08.01'. For use with water up to 65°C.
'KOPATCH PC300-D/BLUE'. Factory applied, two component, dark blue coloured epoxy resin coating. Mix parts A & B in a volume ratio of 2:1. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS dated '9 November 2015'. Cure for 210 seconds@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP01'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'V6.3' issued March 2019. For use with water up to 65°C.
'V-PET #1600 Gray F'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer`s instructions ref. no. '20210216-1' dated 2021/2/16. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vastcoat MT'. Factory applied, blue coloured thermoplastic powder coating. Apply as per manufacturer's instructions 'Issue number 02000202710' dated 20.02.2020. Cure for 10 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions issued March 2017, V4.1. For use with water up to 85°C.
‘Promag’. Factory applied coating system, black coloured, consisting of two component primer and three component polyurethane top coat. Mix primer in a ratio 2:1 by weight (component A:B), apply and cure for 2 hours at 23°C, then mix topcoat in a ratio 100:5.6:2.4 by weight (component A:B:C) before applying and curing for 20 seconds at 23°C. This approval covers the following manufacturing sites: France and China. For use with water up to 23°C.
'EP-621'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions file no: 'TJR-QM-CO-032', 'edition A1' dated '2021-Feb.-26th'. For use with water up to 65°C.
'HEMPADUR 35600 Cream and Red'. Factory applied, cream or red coloured (when mixed), two-component epoxy coatings consisting of a base and curing agent. Mix the base and curing agent in a 14.8:5.2 volume ratio. Cure for 8 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS '20200801 A1'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4807'. Site applied, grey coloured cementitious repair mortar. Mix 'Intercrete 4807' and water in a mass ratio of 9.4:1 Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YHCM-01'. Factory applied, grey coloured sulphate resisting cementitious mortar. Mix sand, cement & water in a ratio of 1: 2.5: 0.3. Cure for 4 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AFIL BLUE Pipe'. Beige coloured GRP pipe manufactured by continuous winding. For use with water up to 50°C.
'TBX 500'. Triple layered, extruded hose comprising of a white coloured, translucent TPE inner layer, black coloured PVC middle layer and grey coloured PVC outer layer. For use with water up to 23°C.
'Grasso L. 100 Lubricating Grease'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Bluesil Paste 408'. White coloured, translucent silicone paste lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
‘Tecomid NA40 GR30 BK005 HS QW, Tecomid NA40 GR35 BK005 HS QW, Tecomid NA40 GR40 BK005 HS QW, Tecomid NA40 GR45 BK005 HS QW & Tecomid NA40 GR50 BK005 HS QW’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
Page 29 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
