Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 7.0bar . Maximum working pressure: 25.0 bar or 30.0 bar depending on model. Maximum operating temperature 80°C.
Range of normally open or closed solenoid valves with brass bodies. Maximum working pressures: SCE210C034BW, SCE210C035BW: AC only 9.0 bar. SCE210C094BW, SCE210D095BW: AC 9.0 bar, DC 3.0 bar. Maximum operating temperature: 85°C
Spherical valves with chrome or nickel plated brass body, chrome plated ball, PTFE seats and FKM ‘O’-ring. The products are available with lever or butterfly operating member. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Lever operated spherical valve with brass body (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline, angled or tee type spherical valves with nickel plated brass bodies and chromium plated brass balls. The valves are either screwdriver or lever operated(see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (HC-A61055-22 model) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of screw down stop valves with brass bodies, EPDM gaskets and PTFE washers. For use with copper pipe to EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 99°C.
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of inlet control groups with DZR brass bodies consisting of an in-line, adjustable pressure reducing valve (adjustable in the range of 1.0 bar to 6.0 bar, pre-set at 3.0 bar), a pressure relief valve (6.0 bar) and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C
Range of bedpan washers with the flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of electrolytic water conditioners, with a brass body and zinc alloy anodes. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. Electrolytic models have a maximum operating temperature of 40°C. Magnetic models are cold water use only.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. 403342 & 403359 Electrolytic models have a maximum operating temperature of 40°C. 403328 & 403335 Magnetic models are cold water use only.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-02 Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'Ascent02-2511', dated '2025.11.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GDPA PermaCoat'. Factory applied, blue coloured (once applied) coating system comprising of a Yellow Zinc Primer and Polyamide top coat. Apply one coat of Yellow Zinc as per work instructions 'PR/WI/01', revision '00', dated '22/11/2017', plating for 45 minutes@30°C. Apply one coat of top coat as per work instructions 'BR/WI/01', revision '00', dated '29/10/2010' and cure for 30 minutes@215°C. For use with water up to 23°C. This material is only approved for the plating and curing conditions that appear on the approval. If the plating and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BAJ0002'. Factory applied, blue coloured epoxy coating. Pre-heat substrate for 30 minutes@200°C and apply in accordance with manufacturer's Product Instructions 'Version-01 202426 September'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix cement, sand, and water in a volume ratio of 1:2.0:0.4 and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Plustek PA7001G7BK11'. Black coloured, injection moulded polyamide material. For use with water up to 85°C.
'PAG11-YT60SF'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'RAMSTER PF100NT'. White coloured (opaque), injection moulded PBT material. For use with water up to 85°C.
'Prime Plastic Industries HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'SOFTPEX V® hose inliner'. Off white coloured (translucent), extruded polyethylene hose. For use with water up to 70°C.
'Qingfa PE100 Black Pipe Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'Radius Systems SC100 (PE100) Dark Blue Pressure Pipe'. Extruded, dual layered pipe comprising of a black coloured PE100 inner layer and a blue coloured PE100 outer layer. For use with water up to 23°C.
'RAK Universal Plastic Industries L.L.C. HDPE PE100 Black Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'ELGEF PLUS'. Black coloured, injection moulded HDPE electrofusion and spigot fittings. For use with water up to 60°C.
'BorSafe™ HE3490-ELS-H,'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'ECOTRAN E1040W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E1040W(#) NC'. Natural (appears brown) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) NC'. Natural (appears beige) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ApiAlu PP-RCT Class 2 Pipe'. Extruded, multi-layered pipe comprising of a green coloured PP-RCT inner layer, aluminium middle layer and black coloured PE 100 outer layer. For use with water up to 85°C.
'RAMOFIN PPH301G6NT'. White/beige coloured, injection moulded polypropylene material. For use with water up to 85°C.
'35444 & 46850'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'F1100'. White coloured (opaque), PTFE material manufactured by extrusion and machining. For use with water up to 85°C.
'F550'. Black coloured (opaque), carbon filled PTFE material manufactured by extrusion and machining. For use with water up to 85°C.
'Anchor Pro Plus'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 2025 - 12 - 09. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ResiFIX Max Performance Epoxy'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's European Technical Assessment ETA-25/1132 of 2025/11/19. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TIMCO VESF 300/VESF 410'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 01.12.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP10/7/7 BLK gaskets & 'O' rings'. Injection moulded, black coloured EPDM gaskets & 'O' rings. Shore hardness 70. The gaskets have an in-radius size of 0.75mm. The ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'GJ-yzxj-V40 EPDM valve seat'. Black coloured, compression moulded EPDM valve seat. Shore hardness 70. Tested in-radius size 3.5mm. For use with water up to 85°C.
'EP2504 (NSF)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'JJSXEPDMIRHD50 (shore hardness 50) & JJSXEPDMIRHD70 (shore hardness 70)'. Black coloured, compression moulded EPDM materials. Tested in-radius size 0.99mm. For use with water up to 85°C.
'E40D'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'Silicone RS7007 Inner Hose'. Colourless (translucent), extruded silicone hose. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'7741'. Red coloured, compression moulded, silicone rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 223 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
