Range of latching solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. The inlet incorporates a stainless-steel strainer. Maximum working pressure 10.0 Bar. Maximum operating temperature 70°C
Range of normally closed solenoid valves with brass bodies, stainless steel spring, EPDM seal and diaphragm. Maximum working pressure - WZS1DF prefix models 7.84532 bar, WSLP1DF prefix models 9.80665 bar. Maximum operating temperature 85°C.
Solenoid valve with plastic body and silicone rubber diaphragm. Maximum working pressure 0.18 Bar. Cold water use only.
Range of spherical valves incorporating brass bodies (model Cim287RB5 nickel plated) brass balls (chrome plated), PTFE seats, EPDM ‘O’-rings and butterfly handle operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of spherical valves incorporating brass bodies and balls (chrome plated), EPDM ‘O’-rings and PTFE gaskets. Products are supplied with either red or blue butteryfly operating member or screw driver operated. Maximum working pressure 50.0 bar. Maximum operating temperature 100°C.
Range of spherical valves incorporating chrome plated brass bodies and balls, and PTFE seats. The products are supplied with either butteryfly or lever handles. Maximum working pressures - see model. Maximum operating temperature 100°C.
Range of spherical valves with brass bodies, brass ball (chrome plated) and PTFE gaskets. Products are supplied with either blue or red lever or butterfly type operating members. Maximum working pressure 50.0 bar (½ models). Maximum working pressure 40.0 bar (¼”, ¾” and 1” models). Maximum working pressure 25.0 bar (1¼” models). Maximum working pressure 16.0 bar (1½” to 4” models). Maximum operating temperature 100°C. Models added March 2022: Maxmimum working pressure of 10.0 bar. Maxmimim operating temperature 60°C (models AI-360115 & 124-3001)
Range of DZR brass gate valves incorporating brass wedges. The Fig 30 range incorporates hand wheel operating members. The Fig 30LS range incorporates a lock shield operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies, wedges and PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating cast iron bodies (blue epoxy coated), EPDM rubber coated wedges and non-rising spindles with hand wheel operating member. Maximum working pressure 10.0 bar (Z45X-10Q model). Maximum working pressure 16.0 bar (Z45X-16Q models). Maximum operating temperature 80°C.
Range of gate valves incorporating DZR brass bodies and wedges, non-rising spindles and handwheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stop valves incorporating brass bodies (brass or chrome plated) with EPDM ‘O’-rings and gaskets. Maximum working pressure 10.0 bar. Cold water use only.
Range of one way and two way manually operated needle valves incorporating brushed stainless steel bodies, rising spindle balancing mechanism and EPDM ‘O’-rings with a metal seat. Maximum working pressure 25.0 bar. Cold water use only.
Range of commercial conveyor type dishwashers with the flow controlled by a solenoid valve and discharged via three type AB air gaps (pre-wash, rinse and wash) (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with a brass bodied ‘Y’-pattern strainer, brass adaptors ¾”x¾” (M)x(M) and (F)x(F) and dual layer PVC inlet hoes(s) (grey outer/black inner) and EPDM washers. The DR*11**** model has two solenoids and requires three inlet hoses and also includes a brass tee-piece to connect them ¾”x¾”x¾” (M). Maximum working pressure 6.0 bar. Maximum operating temperature 60ºC.
Range of commercial front loading dishwashing machines with flow controlled by solenoid and discharged via type AA air gap arrangement. The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 4.0 bar. Cold water supply only.
Electrolytic scale inhibitor incorporating a nickel plated copper body. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitor incorporating a nickel plated copper body. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitor incorporating a nickel plated copper body. Maximum working pressure 10.0 bar. Cold water use only.
Range of ion generating water conditioners incorporating UPVC pipework and fittings, flow meter and stainless steel electrode pens contained within the electrode chamber. Maximum working pressure 9.0 bar. Cold water use only.
Range of undercounter or deck mounted drinking water fountains which dispense ambient and/or chilled water. Flow is controlled via a solenoid valve and the products are activated via a push button or infa-red sensor . Maximum working pressure 7.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'KEPITAL F10-52H Blue'. Blue coloured, injection moulded POM material. For use with water up to 40°C.
`Iupital FG2025MZ`. White coloured, injection moulded POM material. For use with water up to 85°C.
'CT Water - ABS'. Grey coloured, injection moulded ABS end cap. For use with water up to 80°C.
'ABS-010' (grey coloured) & 'ABS-078' (white coloured). Injection moulded ABS materials. For use with water up to 85°C.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions issued March 2017, V4.1. For use with water up to 85°C.
‘Promag’. Factory applied coating system, black coloured, consisting of two component primer and three component polyurethane top coat. Mix primer in a ratio 2:1 by weight (component A:B), apply and cure for 2 hours at 23°C, then mix topcoat in a ratio 100:5.6:2.4 by weight (component A:B:C) before applying and curing for 20 seconds at 23°C. This approval covers the following manufacturing sites: France and China. For use with water up to 23°C.
'EP-621'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions file no: 'TJR-QM-CO-032', 'edition A1' dated '2021-Feb.-26th'. For use with water up to 65°C.
'HEMPADUR 35600 Cream and Red'. Factory applied, cream or red coloured (when mixed), two-component epoxy coatings consisting of a base and curing agent. Mix the base and curing agent in a 14.8:5.2 volume ratio. Cure for 8 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS '20200801 A1'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Balinit DLC-Star.' Factory applied, grey coloured CrN + a-C:H coating. Apply as per manufacturer's instructions reference 'VS200295' dated 18.03.2021. Cure for 6 hours@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`BFSC MAS S&MDN 20`. Factory applied, grey coloured, blast furnace slag cement mortar. Mix sand and cement in a mass ratio of 2.35:1. Add water to give a mass ratio of 1:0.45 (cement:water). Cure first time for 7 hours@70°C. Cure second time for 12 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flogul® 645 Bleu 5005 (blue coloured) & Flogul® 645 Noir (black coloured)'. Factory applied, PVDC coatings to be applied in accordance with manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. Flogul® 645 Bleu 5005 is for use with water up to 23°C. Flogul® 645 Noir is for use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Edelpoxy FN 132 Blue Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions dated 'January 28, 2020'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSP/SF-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'SF-D0001' dated 2021.01.01. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco-Coat FBE Powder PFC/7017'. Factory applied, blue coloured epoxy powder coating. Apply as per instructions for use 'Doc/PFC/703'. Cure for 2.5 minutes@235°C (metal temperature). For use with water up to 85°C. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LDP-800 (1009GBSDT)' - white coloured & 'LDP-800' - blue coloured. Factory applied, fusion bonded epoxy powder coatings. Apply as cure as per manufacturer's user instructions file no. 'NP200917', 'version 1', dated 'Sep, 17, 2020'. For use with water up to 85°C.
'RUNBAO Epoxy resin coating 5017' (light blue), 'RUNBAO Epoxy resin coating 5005' (blue) & 'RUNBAO Epoxy resin coating 3016' (red). Factory applied electro-statically sprayed epoxy resin coating. Apply and cure as per manufacturer's instructions version 'YZRB-2015V1.0' dated '2015-06-01'. Between January 2021 and 9th December 2021, the materials were suitable for use with water up to 23°C. Between 10th December 2021 and 31st January 2026, the materials are suitable for use with water up to 85°C.
'Intercrete 4807'. Site applied, grey coloured cementitious repair mortar. Mix 'Intercrete 4807' and water in a mass ratio of 9.4:1 Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YHCM-01'. Factory applied, grey coloured sulphate resisting cementitious mortar. Mix sand, cement & water in a ratio of 1: 2.5: 0.3. Cure for 4 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Yorkshire Flux 130 (White)`. White coloured paste flux. For use with water up to 85°C.
'OCPOL 611'. Beige coloured (translucent), Isophthalic Unsaturated Polyester Resin with glass fibre material manufactured using hand-lay method. For use with water up to 70°C.
'OCPOL N 7180 E'. Grey coloured (translucent), Isophthalic Unsaturated Polyester Resin with glass fibre material manufactured using hand-lay method. For use with water up to 70°C.
'ResinTech CG10-F-UPS'. Gold coloured ion exchange resin. For use with water up to 65°C.
'Seplite LSF 978 and Seplite Monojet LSF 9780'. Amber coloured ion exchange resins. For use with water up to 85°C.
'Bluesil Paste 408'. White coloured, translucent silicone paste lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Krytox™ Oils; GPL 104, 143AB, VPF 1525, VPF 1531, AUT 1045, GPL 105, GPL 106, 143AC, 143AD & GPL 107'. Clear (colourless), perfluoropolyether oils. 'Krytox™ Greases; GPL 204, 240AB, AUT 2045, GPL 205, GPL 206, 240AC, 240AD & GPL 207'. White coloured, Polytetrafluoroethylene thickened perfluoropolyether greases. All are suitable for use with water up to 85°C.
'RP380s & RP361'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
Page 22 of 226
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
