Range of wafer non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flanged non-return valves with blue epoxy coated ductile iron bodies, EPDM lined ductile iron discs, and EPDM gaskets. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of non-return, swing gate valves with brass bodies and brass discs with a NBR gasket. . Maximum working pressure 16.0 bar or 20.0 bar. Maximum operating temperature 85°C.
Range of pilot operated pressure reducing valves with ductile iron bodies (blue epoxy coating) and EPDM diaphragm and gaskets. The products are supplied with auxiliary fittings: spherical valves, pressure gauges, a pilot valve, a needle valve and copper tubes. Maximum inlet supply pressure 16.0 bar. The outlet pressure is adjustable between 0.6~16.0 bar. Maximum operating temperature 85°C.
Range of single lever ball valves with stainless steel bodies, ball, EPDM O-rings and PTFE gaskets. The press fit connection is to be used with stainless steel pipe manufactured to EN 10312. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating either brass or nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model HC-60982-15) Maximum working pressure 25.0 bar (model HC-62022-15) Maximum operating temperature 85°C.
Range of motorised spherical valves with a stainless-steel body and a separate control box. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of spherical valves incorporating brass bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves operate via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The model has a non-rising spindle and has a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies. EPDM coated ductile iron wedges and a non-rising spindle headwork. Some models incorporate a bypass. Maximum working pressure 16.0 bar. Maximum operating temperature 45°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of gate valves with either brass or DZR brass bodies. The valves incorporate non-rising spindle headworks with a wheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with bronze bodies and rising or non-rising spindles (see model). The MV40-1153.D, MV40.1138RSD, MV40-1138.D, MV40-1128.D and MV40-1138.LSD models are handwheel operated. The MV40-1153.LSD, MV40-1128.LSD, and MV40-1138.LSD models have a lockshield. Maximum working pressures: MV40-1128.D and MV40-1128.LSD models: 16.0 bar, MV40-1138.RSD, MV40-1138.D and MV40-1138.LSD models: 20.0 bar, MV40-1153.D & MV40-1153.LSD models: 25.0 bar. Maximum operating temperature 85°C.
"05 420 00 99, 05 433 00 53, 05 441 06 99, 05 444 00 53, 05 445 00 53, 05 446 00 99, 05 447 00 99 & 05 500 00 99 SERVICING VALVES"
Range of screw down stop valves incorporating brass bodies. The valves are to be used with copper pipe (manufactured to EN1057). Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of commercial dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). Supplied with a Neoperl double check valve and braided connection hose. Maximum working pressure 4.0 Bar Maximum operating temperature 55.0°C
Electrolytic scale inhibitors incorporating nickel plated copper bodies. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Cold water use only.
5705K Electrolytic scale inhibitors incorporating nickel plated copper bodies. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units, for above ground use only. Maximum operating pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 8.6 bar. Cold water use only.
'Nav-Coat Bitumen Paint 001 Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's product information sheet issued '10.07.2009'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZMF7405'. Factory applied, blue coloured Enamel coating. Apply as per manufacturer's TDS 'Version 01', issue date 'December 1, 2025'. Dry for 15 minutes@100°C and then furnace fire for 10 minutes@860°C. For use with water up to 85°C.
‘Nelfapox FW Inert Cream'. Factory applied, cream coloured, two-component epoxy coating. Mix base and curing agent in a 6.8:2 volume ratio. Apply one or two coats as per manufacturer's Technical Data Sheet '999', revision date '24-03-2026'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RTPE100HP' (black coloured with blue stripe) & 'RTPE100LP' (blue coloured) Pipes. Black or blue coloured, extruded HDPE pipes. For use with water up to 60°C.
'RTPE100HF' (black coloured) & 'RTPE100LF' (blue coloured) Fittings. Black or blue coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'CHINAUST F1 HDPE Pipes'. Black coloured (with blue stripes), extruded HDPE pipes. For use with water up to 65°C.
'CHINAUST F1 HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'1021 3-ply Polyethylene Liner'. Blue coloured (transparent) LLDPE polyethylene liner, incorporating a heat weld, manufactured by blown film co-extrusion. For use with water up to 23°C.
'DC-E1M Fitting'. Black coloured, extruded and machined, PE fitting. For use with water up to 60°C.
'Hostalen PP XN125-P' & 'Hostalen PP XN112-I'. Off-white coloured (translucent), compression moulded PP materials. For use with water up to 60°C.
'FLPTFE – 12mm x 12M PTFE Tape'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'Smart S-IRV'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0141’, dated ‘29/11/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Smart S-IRE'. Site applied, light pink coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0187’, dated ‘29/11/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-3030'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 17/0694’, dated ‘09/09/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 17/0694’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-2+’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 14/0346’, dated ‘07/11/2025’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 14/0346’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'OLD B254 50N'. Black coloured, injection moulded IIR material. Shore hardness 50 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'KB60-E'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.2mm. For use with water up to 23°C.
'FOWRY-190920'. Black coloured, compression moulded EPDM rubber. Shore hardness 75. Tested in-radius size 3.0mm. For use with water up to 85°C.
'01/T60FKM 'O' rings and gaskets' – for use with water up to 23°C. 01/T70FKM & 01/T80FKM 'O' rings and gaskets' – for use with water up to 85°C. Green coloured, injection moulded FKM 'O' rings and gaskets. Shore hardness between 60 & 80. In-radius size between 0.5mm & 3.5mm.
'Jelt VA 15-77 (yellow coloured), Jelt VA 15-72 (white coloured) & Jelt VA 16-48 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SHAFPUR/CH | Chrome | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SHAFPUR/BN | Brushed Nickle | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SHAFPUR/AB | Antique brass | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SHAFPUR/GD | Gold | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| AVEPUR/CH | Chrome | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| AVEPUR/BN | Brushed Nickle | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| AVEPUR/AB | Antique brass | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator |
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of WC flushing cisterns incorporating a side entry (delayed action) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The float operated valve incorporates a flow restrictor on the inlet. The cistern is operated by an optional manual dual push button and incorporates a servicing valve on the inlet supply. The waste elbow on model BDS-K210-A01-ESG6 is optional. Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 108-7010 | Chrome plated | 1/2" BSP (F) | 10 bar | 60 °C | CEILSA | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 310-7010 | Chrome plated | 1/2" BSP (F) | 10 bar | 60 °C | CEILSA | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 604587 X XXX | VARIOUS | 3/4” BSP male inlet. | 10 bar | 65 °C | TP | Back of the mixer tap body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1044-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1034-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1033-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1032-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1031-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator |
1.For the series 1044-XX, 1034-XX,1033-XX,1032-XX,1031-XX, the only difference is handle style. 2.XX represent different finishes and can be replaced by CR =Chrome, MB=Matte black, BB=Brushed brass, BN=Brushed nickel,GM=Gun Metal.
Page 205 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
