Ionisation system with stainless steel body and copper & silver electrodes. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Continuous soft water, ion exchange, hydraulically driven water softener (salt regenerated) for domestic use, incorporating LLDPE tubing. Operation is by an ion exchange resin filed plastic pressure vessel, with integral salt cabinet and timer/manual regeneration control. The appliance incorporates single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature Cold water only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'EVER-BLACK 1'. Factory applied, black coloured, modified bitumen coating. Apply as per manufacturer's TDS TDS 'V1', dated '2023.03.05' and cure for dry/cure for 7 days@25°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CER4'. White coloured ceramic disc manufactured by dry-press. For use with water up to 85°C.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Promag D - Flowtube'. Black coloured, injection moulded PA flowtube. For use with water up to 60°C.
‘PolySTH Pipe’. White coloured, extruded multi-layered pipe consisting of a polybutylene inner and outer layer and an EVOH middle barrier layer. For use with water up to 85°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
'TW03'. White coloured (translucent), injection moulded polyethylene thrust washer. For use with water up to 85°C.
'Hydropriv PE100 Pipe'. Black coloured (with blue external stripes) and blue coloured, extruded PE100 pipe. For use with water up to 23°C.
'Hydropriv PE80 Pipe'. Black coloured (with blue external stripes) and blue coloured, extruded PE80 pipe. For use with water up to 23°C.
'HIDRONIX PE-RT TYPE II/AL/PE-RT TYPE II Multilayer Pipe'. Extruded, multi-layered pipe comprising of a white coloured PE-RT TYPE II inner and outer layer and aluminium middle layer. For use with water up to 85°C.
'Drincable 800'. Blue coloured, extruded, cylindrical shaped EPDM cable. The EPDM outer sheath is the water contact part and has a shore hardness of 50 and tested in-radius size of between 0.6mm & 1.75mm. For use with water up to 23°C.
'ARCO-DRINKFLEX Cable'. Blue coloured, extruded, submersible EPDM cable. Shore hardness D 23. Tested in-radius size of the sheath is 2.5mm. For use with water up to 23°C.
'AquaPure 2025'. Beige coloured tube manufactured by winding PET fibre and epoxy vinylester resin over a mandrel under heat and pressure, intended for the manufacture of bearings. For use with water up to 23°C.
Range of wall mounted electric showers (various finishes). The E2WXX, E2BXX & E2GXX models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The E1WXX & EW1WXX models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. For use with cold water only
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Four-hole, single outlet, (fixed) combination tap assembly with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies between the side valves and spout, and also on the diverter outlet at the base of the spout. The product is also supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FLKIT40 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT60 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT80 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
Concealed 2-way or 3-way brass body diverter valve (see models) with or without shut off mechanism (see model) and various trim sets and operating members (see model). Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60.0°C.
Concealed self-cancelling control with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). (brass body) with a variety of operating member styles. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60.0°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-1 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-2 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-3 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No |
D30PF and D30PF-1 only different in the color of Item 11 and Item 13 D30PF-2 and D30PF-3 only different in the color of Item 11 and Item 13 DN30PF and D30PF-2 only different in the shape of Stem
Range of deck mounted ceramic cartridge and single sequential headwork assemblies, (brass bodies – various styles and finishes), incorporating a range of operating members. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AB-2047-F | 34.0 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2053-F | 33.6 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2057-F | 26.8 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2058-F | 27.5 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2058-S | 27.2 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2059-F | 34.0 mm Ø | 24 bar | 85 °C | Xingle | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8142KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8122KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8142KPM-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
1）Model No. without Suffix-Chrome 2) -**Represents the following different surface treatments: 1. H-Black 2. DYB - Matte white 3. BZ - Perl white painted 4. HGTS - Red bronze 5. HTL = Yellow bronze brushed 6. Q = Bronze 7. QTSL = Bronze brushed bright 8. QTS = Bronze brushed matte 9. STS = Acid copper brushed 10. SDMGJ = Water plated rose gold 11. N = Nickel brushed bright light 12. NP = Nickel brushed 13. TJ = Titanium gold 14. TJLS = Titanium gold brushed 15. G = Gold 16. GJS = Gold brushed 17. GJSY = Zirconium gold wire drawing matte 18. PGJFY = Zirconium gold wire drawing matte bright light 19. PLSJ = Brushed gold 20. LSJY = Brushed gold matte 21. MGJ = Rose gold 22. MGJL = Rose gold brushed 23. DMGJ = Light rose gold brushed 24. HTS = Red bronze brushed 25. QHP = Grey 26. LSQH = Grey brushed 27. LHMGJ = Brushed yellow rose gold 3) The finish is on metal body
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T21002L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21002 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21002M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T31502 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T31502M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T50802L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T50802M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T50802 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T10102 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Filter | |
| SL-T20402 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T40202 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| SL-T40102W | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | C-plate | Flow Straightener |
Various finish: (1) Without suffix to current model number: Chrome plated (2) With suffix B: Black (3) With suffix BB: Brushed brass (4) Models SL-T40202 & SL-T40102W with suffix G: Champagne Gold
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL ES BAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| AL ES BAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| AL ES BAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| AL ES TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| AL ES TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| AL ES TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CRU TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Flow Regulator Fitted, |
| CRU TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Flow Regulator Fitted, |
| CRU TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Flow Regulator Fitted, |
| 313935 | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Flow Regulator Fitted, |
| 313936 | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Flow Regulator Fitted, |
| 313937 | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 12101246 | Various | 1/2" captive nut | 10 bar | 65 °C | EASO | Rear of body | No | 1/4 Turn ceramic disk | Nut with screws | Aerator |
Chrome plated, Brushed brass, Brushed nickel or Matt black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8125KP | Various | BSP 3/4" (M) | 10 bar | 85 °C | “LANBIAO” | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| F8145KP | Various | BSP 3/4" (M) | 10 bar | 85 °C | “LANBIAO” | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
1）No Suffix-Chrome 2) -**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold 3) The finish on metal body
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T10105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T20405 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21005 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T30605W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T31505 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40105W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T40205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T40415 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T50805 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
1.The model number suffix without B indicates chrome plated. The model number suffix with B indicates black. The model number suffix with BB indicates Brushed brass. 2.Only SL-T40415, SL-T40205 & SL-T40105W suffix with G indicates Champagne Gold.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
The model without a suffix indicates chrome. The model number with suffix B indicates black. The model number with suffix BB indicates Brushed brass.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M5005 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| LIS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| LIS BSM BLK | Black | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| RP3 LIS BSM C | Chrome (Cr3) | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| ELE BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| ELE BSM BLK | Black | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21001 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T31501 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T50801 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T30601W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T20401 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T40201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40401R | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40101W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T10101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products Incorporate either a non-rising spindle (model 1641 only) or quarter turn ceramic disc headworks (all other models) with either cross top (model 1641 only) or single lever (all other models) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a a pop-up waste not verified by test. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products incorporate either a non-rising spindle (model 1851 only) or quarter turn ceramic disc (model 1850 only) headworks with either cross top (model 1851 only) or single lever (model 1850 only) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts and lever operated pop-up wastes. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313941 | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313942 | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313943 | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
Page 19 of 20
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
