Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models RSF-002A(Metal Seat) & RSF-002B(Metal Seat) incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of non-rising spindle gate valves with bronze, brass or DZR brass (V2143R) bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar (V2143R) 25.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of plastic, push-fit stop valves for use with MDPE pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of Electromagnetic water conditioners. Maximum working pressure 16.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
'ANUBIT HB-1000'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's TDS 'AE-TDS-023-2021', dated '02.08.2024'. Please note that use of a thinner isn't covered by the scope of this approval. Cure for 40 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac High Build Bituminous Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's work instruction document 'GPC/WI/10' issue no. '01', dated 03/01/2018. Cure for 72 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-021'. Factory applied, yellow coloured, two-component polyurethane coating. Components A and B are preheated to 65°C and then mixed & sprayed (using a thermal spraying instrument) in a volume ratio of 1:1 according to Application Instructions dated 'APR 2013'. Cure for 7 days@23°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-010Y'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'JXT/JS02-10', edition '1/0', dated '2021-11-30'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue and Jotapipe AC - 1003 Green'. Factory applied, blue or green coloured fusion bonded epoxy coatings (manufactured in Dubai, U.A.E). Apply as per manufacturer's Technical Data Sheet dated 26th September 2019. Cure for 2 minutes@245°C. The blue coating is for use with water up to 85°C. The green coating is for use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-XP2501'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'XP2503-010', dated '2025-03-25'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-RVK2025'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'RVK2503/25', dated 'March 25, 2025'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Guom-07'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a weight ratio of 1:1.5:0.6 and apply as per manufacturer's User Instructions 'GUOM-24', 'Vision: B', dated '2024-11-5'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MAVM554'. Factory applied, blue coloured, epoxy powder coating. Apply as per manufacturer's data sheet 'FR.07.03.18', dated 09.19. Cure for 10 minutes at 160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Solvent Free Epoxy Coating XH4205'. Factory applied, white coloured, two-component epoxy coating. Mix Coat 1 (XH4205/grey coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 24 hours@25°C. Mix Coat 2 (XH4205/white coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue & Green. Factory applied, green or blue coloured epoxy coatings (manufactured in Dammam, Saudi Arabia). Apply as per manufacturer's MTI '001 - 2024 - SA – EN'. Cure for 4 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electroline ES 424'. Factory applied, white coloured, two-component epoxy coating. Mix Part A and Part B in a volume ratio of 2:1 and apply as per manufacturer's TDS 'ECL/ TDS / ES424', version '0', dated '05.01.2024'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat Epoxy Blue Patch Up Paint (PFC/1017)'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:2 volume ratio and apply as per manufacturer's IFU 'DOC/PFC/PU/101', dated '01.04.2024'. Cure for 8 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`MECH WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions '24136' dated 2025/1/26. For use with water up to 85°C.
'Carboguard AQP FC Part A and Part B'. Site applied, grey coloured (once applied) epoxy coating. Mix Parts A & B in a weight ratio of 1:1 and apply as per manufacturer's Product Data Sheet '8163', dated 'March 2025'. Cure Coat 1 for 24 hours at 20°C and Coat 2 for 7 days at 20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monoflex W'. Grey coloured, extruded TPO 'tape'. Shore hardness 91. Tested in-radius size between 0.45mm & 1.0mm. For use with water up to 70°C.
'LEAKBLOK® P100'. Green coloured fibre/NBR gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'SANIBIW WB60 & SANIBIW WB80'. Off-white coloured, transparent, extruded silicone rubber hoses. Shore hardness 60 & 80. Tested in-radius size between 0.5mm & 1.5mm. For use with water up to 85°C.
'EPDM W8528'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SL7065/SL7015'. Extruded, triple layered hose comprising of a translucent, silicone inner layer, white coloured polyester middle layer and translucent, silicone outer layer. Shore hardness 70. Tested in-radius size of complete hose is 1.8mm. For use with water up to 65°C.
'Hydropriv PE100 Pipe'. Black coloured (with blue external stripes) and blue coloured, extruded PE100 pipe. For use with water up to 23°C.
'T-MECH PE-Xb Pipe’. White coloured (opaque), extruded PEX pipe. For use with water up to 85°C.
'R579 TP13582 BLACK & R579 TP14619 BLACK'. Black coloured, rotomoulded PE materials. For use with water up to 85°C.
'Tecotek OP20 GR30 BG018 01 0A QF'. Beige coloured, injection moulded PPO/HIPS material. For use with water up to 85°C.
'Fortron® 1130T4 SD3039 Black'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Hostalen PP H2142 12'. Black coloured, injection moulded and compression moulded polypropylene material. For use with water up to 23°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'Dalcon 001'. White coloured, compression moulded or extruded PTFE material. For use with water up to 85°C.
'PVDF Solef® 1008/0HP1'. White coloured, injection moulded PVDF material. For use with water up to 85°C.
'PVDF Solef® 1010/0HP1'. White coloured, injection moulded PVDF material. For use with water up to 85°C.
'PVDF Solef® 1010/0UP1'. White coloured, injection moulded PVDF material. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'51M7568'. Black coloured, injection moulded EPDM material. Shore hardness 75 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NE7130-XT'. White coloured (translucent), injection moulded Silicone rubber. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Page 179 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
