'Electrocement CEM1-SR3 - Dalmia SRPC'. Factory applied, grey coloured sulphate resisting Portland cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 83275'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS-2025-AL83275-REV00', dated '03.07.2025'. Cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'SH Special Seal grease'. Opaque, white coloured silicone grease. Apply as per manufacturer's instructions. No cure required. For use with water up to 65°C.
'SILICOMPOUND FCA 125'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Badadur PBT9 GF30 graphit 371 (grey coloured) & Badadur PBT9 GF30 Alpinweiss 230c (white coloured). Injection moulded Polybutylene terephthalate (30% glass fibres) materials. For use with water up to 65°C.
'Fox Spigot and Electrofusion Fittings'. Black coloured, injection moulded polyethylene spigot and electrofusion fittings. For use with water up to 65°C.
'PE002'. Blue coloured, extruded HDPE pipe. For use with water up to 60°C.
'aquatherm PE-RT pipe'. Off-white coloured, extruded PE-RT (Type 1) pipe. For use with water up to 65°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
‘RIALENE P 100 SGFxx KTW grau K 7-128, RIALENE P 100 SGFxx KTW weiß K 9-112, RIALENE P 100 SGFxx KTW schwarz’, injection moulded polypropylene materials available in grey, white and black. ‘RIALENE P 100 SGFxx KTW natur(al)’, natural (appears off-white), injection moulded, polypropylene material was added to the approval in February 2026. The ‘xx’ in the material name can be replaced with any number between ‘10’ and ‘50’. For use with water up to 85°C.
'HC-EP7001165PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51M6767'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 0.5mm. For use with water up to 60°C.
'51M5567'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 0.5mm. For use with water up to 23°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'TWK3628'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 0.5mm. For use with water up to 60°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'Loxeal 85-86'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'ONEBOND ADHESIVO PVC PROFESIONAL'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BLAZEMASTER® 88065 Orange 734 M PEL 8065OMAM'. Orange coloured, injection moulded c-PVC fittings. For use with water up to 23°C.
Range of single hole, double outlet (fixed) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied). All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature 98°C. Hot-water circuit has a maximum operating temperature of 65°C.
Range of deck mounted two hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes), incorporating a ceramic disc headwork controlling the flow with a dome type operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. The spout outlet incorporates a plastic aerator. Models SHTLV106/1B & SHTLV106/2BK are supplied with a shower hose & shower handset and riser rail. Model TLV106 is supplied with a shower hose & shower handset. All models are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes), incorporating a ceramic disc headwork controlling the flow with a dome type operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. The spout outlet incorporates a plastic aerator. All models are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH71 | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | |||
| GUTH61 * | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk |
Product Identification with an * as suffix = models added 11/082025
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM 3WDIV C | Chrome | 15mm Compression | 10 bar | 60 °C | Bristan | Faceplate | No | Not applicable | Not Applicable | Not Applicable |
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies models HVDCVC-31, HVDCVC-32 are chrome plated. Maximum working pressure 16 Bar Maximum operating temperature 60°C
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel nozzle) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Some models incorporate a stainless-steel strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 812003A | 23.8mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812038A | 23.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812049A | 19mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812056 | 18.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812057 | 19.0mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812072 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812073 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812114 | 18.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TM001 | Black | Ø 33.81mm | 5 bar | 85 °C | Company logo and date of manufacture (DD/MM/YY) | Body | No | Not applicable | Not Applicable | Not Applicable | |
| TM006 | Black | Ø 26.66mm | 5 bar | 85 °C | Company logo, Sedal and date of manufacture (DD/MM/YY) | Body | No | Not applicable | Not Applicable | Not Applicable |
Single hole, single outlet (swivel) combination tap assembly with white finish brass body), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headworks with a cross top operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 233308 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 Bar Maximum operating temperature: 65°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies -various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0Bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQSOL EFSNK C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 4648G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288489 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288491 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311098 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 3311102 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311106 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311162 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQMEN EFSNK BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 9087G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288493 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288503 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311105 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311114 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311125 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311164 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disc | C-plate |
Model added February 2026: RP3 EC SNK EF BLK
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes) incorporating 1/4 turn ceramic disk headworks and single lever operating members. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Page 146 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
