'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/A)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/B)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.1 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver 1 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure for 6-8 hours@10°C or 3-4 hours@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure in accordance with manufacturer’s IFU ’06-03-19’, ‘Completion of the Molecular Reaction’ table, ‘Full mechanical/thermal loading or water immersion’. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless RF35 (2024) Coating System’. Site applied, grey coloured (once applied), two-part epoxy coating. The primer comprises of ‘Corroless EPF (2022) Primer Base Red’ and ‘Corroless EPF (2022) Buff Temperate Hardener’, to be mixed in a 1:1 volume ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 24 hours at 10°C. The coating comprises of ‘Corroless RF35 (2024) Base 00-A-01 Portland’ and ‘Corroless RF35 (2024) Hardener’, to be mixed in 5.5:1 weight ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 7 days at 10°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'REGZ40 & REGZ41'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'BX-455'. White coloured (opaque) Silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
Grilamid LV-30H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA natural. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural & Grilamid LV-65H FWA black 9225 were added to the approval in March 2026. Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. For use with water up to 85°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'Revolve M-748 Black'. Black coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
‘Udel P-3500 NT LCD, GF-110 NT, GF-120 NT, GF-121 NT, P-1700 NT 11 MR, P-1700 NT 11, GF-121 NT ECHO RP & P-3500 NT LCD ECHO RP’ (all beige translucent). ‘Udel P-1700 Grey 8057’ (grey coloured). ‘Udel P-1700 BK 937, P-1700 BK 937 MR, GF-120 BK 937, GF-121 BK 937, GF-121 BK 937 ECHO RP, GF-120 BK 937 ECHO RP & P-1700 BK937 ECHO RP’ (all black coloured). ‘Udel P-1700 WH 7407’ (white coloured). Injection moulded, polysulphone materials. For use with water up to 85°C.
‘AQI380PRO’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’Load time’ cures set out in Table B4 of European Technical Assessment ETA 19/0127’, dated ‘28/02/2019’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’Load time’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 19/0127’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Dutral K-Co-054'. Black coloured, compression moulded EPDM materials. Shore hardness between 52A & 80A. Tested in-radius size 1.0mm. For use with water up to 65°C.
Range of injection moulded, VMQ rubber gaskets, seals, & `O` rings manufactured from the below compounds. The components are available in blue, green, grey, opaque (beige coloured), red, transparent & yellow. The numbers in the name of the compound indicates the shore hardness between 40 & 80. Tested in-radii sizes: Gaskets: 0.2mm - 5.0mm. Seals & `O` rings: 0.5mm - 5.0mm. S50B04E, S60B00E, S70B06E, S70B07E, S70V02E, S50V01E, S60O02E, S70O05E, S50O03E, S50O05E, S60O01E, S70O03E, S40A01E, S60A00E, S70A02E, S40R03E, S45R01E, S50R10E, S50R01E, S60R05E, S65R04E, S70R04E, S80R01E, S40R02E, S50R06E, S60R07E, S70R19E, S70R24E, S50T05E, S50T00E, S55T00E, S60T00E, S60T00T, S70T04E, S70T00E, S75T00E, S80T00E, & S70G01E. For use with water up to 85°C.
72401, 72501, 73401, 73501, 74401, 74501, 75401, 75501, 76401, 76501, 77401, 77501, 78401, 78501, 79401 & 79501. Range of press moulded, solid silicone rubber materials which are blue or red coloured. Shore hardness between 20 & 90. Tested in-radius size 1.0mm. for use with water up to 85°C.
'Hytrel® 4068FGDW'. Cream coloured, injection moulded, thermoplastic polyester elastomeric material. For use with water up to 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 4203801-1 | chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, |
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated inlet valves, for WC flushing cisterns with plastic bodies and adjustable floats and a plastic flow regulator at the inlet. Maximum operating pressure: 10 bar. Maximum operating temperature: 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT103002000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT104001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT125001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT105501110XX | See Below | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | Lever | No | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
Range of spherical valves with DZR brass bodies, chromium plated brass balls, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Compression connection to be used with copper EN1057. AI-0396A062815CR incorporates an approved single check valve cartridge, verified by test - suitable for backflow protection against fluid category 2. Maximum working pressure: 25.0 bar. Maximum operating temperature: 100°C (model AI-0396A062815CR 65°).
Range of shower hoses. The H-38033 model has a PVC inner liner and stainless steel interlocked outer casing. The H-38034 and H-38035 models are multi-layer shower hoses with a PVC inner liner. Maximum operating temperature 60°C. Open outlet use only.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814110 | chrome | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, | ||
| 814112 | 814112 | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, |
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum operating pressure 10.0 bar. Maximum operating temperatures: 430357-003, 430357-004 and 430357-006 models: 85°C, 430357-008, 430357-010, 430357-011 and 430357-012 models: 65°C.
Non-verifiable single check valve assembly with a stainless-steel body. Maximum working pressure 10.0 bar. Maximum operating temperature of 85°C.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘TankBoost 5 bar’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks and cross top operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste (not verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Non rising spindle headwork incorporating a brass body and NBR seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headwork assemblies with brass bodies, NBR ‘O’-rings and silicone gaskets. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with EPDM seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar, Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| D39 | 39mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge |
Model D25-2 and D39 are diverter with open/close function
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 501102 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 501101 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591103 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141102 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator |
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies, chrome finish(chromium plated brass), with a non-rising spindle and cross-top operating member(models 49944 & 88081) or ceramic disc headwork with lever type operating members(model 26251). The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L449200DH | Matt black | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200MA | Tri-chrome | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200SA1 | Brushed gold | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 141701 | chrome | 1/2" BSP | 10 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 503109 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 5593201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 143201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, |
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Models 91742, 805777 & 21775 incorporate a non-rising spindle headwork. Models 91742 & 805777 with dome type operating members Model 21775 with lever type operating members. Models 77174 & 805783 incorporate a quarter turn ceramic disc headwork with dome operating members. The fitting incorporates a manual diverter to the shower outlet The spout outlet incorporates a plastic flow straightener and the products are supplied with a shower hose, shower handset and metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| J THBSMVO C | Chrome | G 3/4" (M) | 10 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K005* | Various | ½" captive nut | 5 bar | 65 °C | WINSDRUM | On Spout | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| K008* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 20.189.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| 20.193.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
Where xxx denotes finish, can be replaced by: 002 – Chrome DC2 – Supersteel DA2 – Warm sunset AL2 – Brushed hard graphite A02 – hard graphit DL2 – brushed warm sunset GN2 – brushed cool sunrise A02 – hard graphite MS2 – satin steel GL2 – cool sunrise MS2 – satin graphite
Page 115 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
