Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Range of wall mounted, exposed, thermostatic shower valves (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature with a single lever operating member. The products are supplied with 15mm compression inlet elbows incorporating approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets also incorporate plastic flow regulators. The 90033CP model can have either a top or bottom outlet, which is achieved by re-positioning the blanking plug and threaded outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC.
Drain valve with a brass body, spindle and EPDM O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of T-type thermostatic mixing valves with DZR brass bodies. Temperature is pre-set under a fixed cap. The inlet adaptors incorporate single check valve cartridges (verified by test, suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
T-type thermostatic mixing valve with a DZR brass body. Temperature is pre-set under a fixed cap. The 90° angled inlet adaptors (AI0496BAG.2 & AI0505SBAG.2) incorporate stainless-steel strainers, integral spherical valves and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. From November 2020 the products are also available with chrome plated brass inline inlet adaptors (AI090815.1 & AI090822.1), each incorporating a stainless-steel strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). They can also be supplied with chrome plated brass 90° angled inlet adaptors (AI0496BAG.1 & AI0505SBAG.1) which incorporate a stainless-steel strainer, integral spherical valves and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Self-closing combination tap assembly (chromium plated brass) with spring loaded headwork controlling both the flow and temperature with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The inlets of the main tap body incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Tundish with a black plastic body and a straight through pattern. The product satisfies the requirements of air gap to drain.
Range of wall mounted shower outlets (chromium plated brass bodies). Maximum operating temperature 85°C.
Range of lever operated spherical valves with brass bodies and chrome plated brass ball. Model 7214335-1 is supplied with a drain off. Maximum working pressure 10.0 bar, Maximum operating temperature 85˚C.
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate a quarter turn spherical valve with single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Wondervalve®Lite range of lever or screwdriver operated spherical valves with brass bodies and chrome plated brass balls and PTFE seats. The valves incorporate either a 4, 6, or 8l/min flow regulator (see model section). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of in-line `Y` patterned strainers with brass bodies, incorporating a spherical valve using a butterfly type operating member, EPDM ‘O’-rings and stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of T-Type thermostatic mixing valves (chrome plated brass bodies). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
T type thermostatic blending valve having a DZR brass body and NBR o rings. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate a quarter turn spherical valve with single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Continuous circulation spherical valve with brass body and plastic ball with lever type operating member. The product incorporates a screw in drain off valve on the side of the valve. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Stainless steel braided EPDM lined flexible hose assembly with EPDM O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Wall mounted, two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow using a dome type operating member. Temperature is controlled via a thermostatic cartridge also using a dome type operating member, also incorporating a lockable diverter to shower outlet. The inlets incorporate a stainless-steel filter and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow using a dome type operating member. Temperature is controlled via a thermostatic cartridge also using a dome type operating member, also incorporating a lockable diverter to shower outlet. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted, two-hole, single shower outlet combination tap assemblies (chromium plated brass). The flow is controlled by a ceramic disc headwork (with various operating members). temperature is controlled VIA a thermostatic cartridge (with various operating members which incorporate a manual override button). Both inlets incorporate approval single check valve cartridges, however the complete unit has not been tested to show it provides back flow protection. Models ST20015CP & COOR incorporate elbows. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of plastic bodied (chrome plated) overhead shower outlets, with NBR and/or EPDM ‘O’-rings. The inlet incorporates a combined EPDM washer with a stainless steel strainer. Maximum operating temperature 60°C.
T-Type thermostatic mixing valve (chromium plated brass). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two-hole, single shower outlet combination tap assemblies (chromium plated brass). The flow is controlled by a ceramic disc headwork (with various operating members). temperature is controlled VIA a thermostatic cartridge (with various operating members which incorporate a manual override button). Both inlets incorporate approval single check valve cartridges, however the complete unit has not been tested to show it provides back flow protection. Models IN10015CP incorporate elbows. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated DZR brass body. Product also incorporates an isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Wall mounted, exposed bar type thermostatic blending valve (chromium plated brass), incorporating a quarter turn ceramic disc controlling the flow with single lever operating members. The temperature is controlled independently via a thermostatic cartridge with single lever operating members. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of chrome plated plastic shower handsets with EPDM ‘O’-rings and flow restrictor. Maximum operating temperature 60ºC.
Wall mounted exposed thermostatic blending valve (chromium plated brass body) incorporating a half turn ceramic disc headwork controlling the flow to either the overhead shower or hand shower with a dome type operating member. The temperature is controlled via thermostatic cartridge with a manual override button and dome type operating member. The inlets incorporate stainless steel strainers and approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Non-verifiable single check valve assembly with chrome plated DZR brass body. Maximum working pressure 14.0 bar. Maximum operating temperature 85ºC.
Wall mounted exposed bar type thermostatic blending valve (chromium plated brass) with a half turn ceramic disc headwork controlling the flow and a thermostatic cartridge controlling the temperature, both with cubed type operating members incorporating manual override buttons. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60.0°C
Wall mounted, thermostatic shower valve (chromium plated brass). The flow is controlled by a quarter turn ceramic disc headwork with a dome type operating member. The temperature is controlled by a thermostatic cartridge with dome type operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a stainless steel braided, PVC lined shower hose, chrome plated plastic shower handset and riser rail. The inlet of the shower handset incorporates a plastic flow restrictor. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Wall mounted thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member. Both inlets incorporate single check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2) and a stainless-steel filter. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of spherical ball valves with single lever or T-handle operating members, brass bodies (nickel plated) and chromium plated brass ball and PTFE washers. Maximum working pressure IN90 models = 40.0 bar. IN89 models = 25.0 bar. Maximum operating temperature 85.0°C
Range of shower handsets incorporating ABS bodies (chrome plated), EPDM seals and ‘O’-rings. Maximum operating temperature 65°C.
Wall mounted exposed bar type thermostatic blending valve (chromium plated brass) with a half turn ceramic disc headwork controlling the flow and a thermostatic cartridge controlling the temperature, both with cubed type operating members incorporating manual override buttons. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60.0°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of flow through valves with brass bodies and EPDM ‘O’-rings, incorporating a spherical valve and a separate drain tap. The products are intended for connection prior to an expansion vessel. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of adjustable T type thermostatic blending valves (DZR brass) with push-fit connections for use with copper, PE-X (BS7921 Part 3: 2010) and Polybutylene (NBS7921/2) pipe. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Spherical valve incorporating a DZR brass body, chromium plated brass ball & single lever operating member, with push-fit connections for use with copper, PE-X (class B1) and Polybutylene (class B1) pipe. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
T-type thermostatic mixing valve with brass body, EPDM ‘O’-rings and stainless-steel strainers. The inlets incorporate stainless-steel strainers and an approved check valve cartridge verified by test (as suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of automatic air venting valves with a brass body and a plastic float. Maximum working pressure 10.0 bar. Maximum operating temperature 115°C.
Range of spherical valves with nickel platedbrass bodies, nickel plated brass balls and EDPM ‘O’-rings with a lever type operating member. Maximum working pressure 50.0 bar. Maximum operating temperature 85°C.
Range of in-line adjustable pressure reducing valves with Nickel plated DZR brass bodies and EPDM gaskets. Maximum inlet supply pressure 16.0 bar. Outlet pressure in the range of 0.5 bar to 6.0 bar. Maximum operating temperature 80°C.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM seat washers & ‘o’ rings and stainless-steel filters. Various models supplied with pressure gauge (please see model list). Maximum inlet supply pressure 16.0 bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of wall mounted, two hole, single outlet (fixed) mains electric or battery controlled tap assemblies (chromium plated brass) incorporating approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection . The flow is controlled via a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The tap is supplied with spherical valves for both hot and cold inlets. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of spherical valves incorporating brass bodies and balls (nickel plated), EPDM rubber ‘O’-rings, PTFE seats and red or blue coloured lever type operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spherical valve incorporating a brass body (brushed chrome), chrome plated brass ball, ‘y’-patterned strainer, PTFE seats and single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Wall mounted thermostatic bar type shower valve incorporating a ceramic cartridge headwork, with single lever operating member, which controls and diverts the flow between the two shower outlets. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member which incorporates a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Electronically controlled heat interface units (HIU) with twin stainless-steel plate heat exchangers providing space heating and instantaneous hot water. The cold inlet supply to the plate heat exchanger incorporates an isolation valve and a water hammer arrestor. The space heating circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product is supplied with a filling loop assembly consisting of an elbow shaped copper pipe, isolation valve and double check valve assembly (suitable for backflow protection against fluid category 3) which incorporates an isolation valve. The cold mains inlet and the domestic hot water outlet each incorporate a brass bodied spherical valve with a butterfly handle. Maximum working pressures and operating temperatures: Primary: 16.0 bar and 90˚C. Domestic hot water (DHW): 10 bar and 65˚C. Secondary (space heating): 2.5 bar and 85˚C.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM seat washers & ‘o’ rings and stainless-steel filters. Various models supplied with pressure gauge (please see model list). Maximum inlet supply pressure 16.0 bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Water hammer arrestor with brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of shower outlet with chromium plated bodies with check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum operating temperature 70°C. Open outlet use only.
Wall mounted, exposed, thermostatic bar type shower mixing valve (chromium plated brass) incorporating a 2-way ceramic disc diverter headwork with a dome type operating member, which diverts the flow between outlets. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a combined NBR washer and stainless steel strainer and an approved single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, thermostatic shower valve (chromium plated brass). The flow is controlled by a quarter turn ceramic disc headwork with a dome type operating member. The temperature is controlled by a thermostatic cartridge with dome type operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a stainless steel braided, PVC lined shower hose, chrome plated plastic shower handset and riser rail. The inlet of the shower handset incorporates a plastic flow restrictor. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of cold-water inlet control groups with DZR brass bodies consisting of an in-line, adjustable pressure reducing valve (PRV) (adjustable in the range of 0.8 bar - 6.0 bar, but factory pre-set at 3.0 or 3.5 bar - see model), strainer and a DZR brass bodied pressure relief valve (SRV) (set at 4.75 bar or 6.0 bar - see model). Products also incorporate an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 16.0 bar. Maximum operating temperature 80°C.
Wall mounted, bar type, thermostatic shower mixer (chromium plated brass), incorporating a ½ turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The TR10032CP model is supplied with a riser rail, shower hose and handset. The TR10010CP is the valve only. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted compact shower panels with push button timed flow control. The inlet incorporates a plastic flow regulator and a stainless-steel strainer. Maximum working pressure 4.0 Bar Maximum operating temperature 60°C
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of deck mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic flow straightener. During January and February 2022, the products are supplied with metal back nuts. From March 2022, the products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
A range of wall mounted self-closing shower valves (chromium plated brass), incorporating a spring loaded headwork with a dome type operating member. Model TF222CP250 is supplied with metal back nut. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated). Incorporating quarter turn ceramic disc headworks, dome type operating members and self cancelling diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Models TL30024CP and TR30024CP are supplied with a shower riser rail, shower hose and shower handset. Maximum working pressure 5.0bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated). Incorporating non-rising spindle headworks, dome type operating members and lockable, self cancelling diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of deck mounted non concussive taps (chrome plated brass) incorporating a spring-loaded headwork operated via a single lever operating member. The outlet incorporates a flow straightener and the product is supplied with plastic backnuts. Maximum working pressure: 10.0 bar. Maximum operating temperature: 65°C.
Range of wall mounted non concussive taps (chrome plated brass) incorporating a spring-loaded headwork operated via a single lever operating member. The outlet incorporates a flow straightener. Maximum working pressure: 10.0 bar. Maximum operating temperature: 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature using a single lever operating member. Inlets incorporate an isolation valve, stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. HTMDMRS model is supplied with a removable spout. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature using a single lever operating member. Inlets incorporate an isolation valve, stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. HTMWMRS is supplied with a removable spout. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of in-line adjustable pressure reducing valves with DZR brass bodies and EPDM ‘O’-rings and gaskets, for use with copper pipe (manufactured to EN1057). The valves incorporate test ports at the outlet. The product is supplied with an optional pressure gauge. The outlet pressure is adjustable between 1.0 bar and 6.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 80°C.
Combination tap assembly (chrome plated brass), with a dome type operating member controlling the flow and temperature with a non-concussive thermostatic cartridge headwork. The spout outlet incorporates a plastic aerator. The inlets incorporate approved single check valve cartridges, however, the complete assembly has not been tested to demonstrate backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic shower panels incorporating a single sequential thermostatic control valve with a single lever operating member and flexible riser kit. Each inlet supplied with a servicing valve, EPDM o-ring and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with black lined PVC shower hoses and chrome plated shower handsets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 1.0 bar. Maximum operating temperature 65°C
Range of ‘IBall Vortex’ flow through valves with brass body and EPDM ‘O’-rings incorporating a plastic spherical valve and a drain tap. Maximum working pressure: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Activflo range of water conditioners with stainless steel bodies. Models with compression connections are for use with copper pipe (manufactured to BS EN 10 57), stainless steel pipe (BS EN 10312:2002), polybutylene (BS 7291-2) or PE-X pipe (BS7291-3). Maximum working pressure 16 bar. Maximum operating temperature 99°C
Screwdriver operated spherical servicing valve with chromium plated brass body, brass ball and EPDM O-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Filling loop assemblies consisting of a stainless steel braided EPDM lined flexible hose, an isolation valve and another isolation valve incorporating a non-verifiable double check valve assembly, verified by test (suitable for backflow protection against fluid category 3). The FL12041515 model is supplied with an isolation valve including a dial type pressure gauge. The FL12041525 model is also supplied with brass end caps incorporating EPDM washers. For use with coper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Rigid filling loop assembly, consisting of a lever operated brass spherical valve and a DZR brass double check valve assembly (verified by test as suitable for backflow protection against Fluid Category 3) that incorporates a lever operated spherical valve. For use with copper manufactured to BS EN 1057. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Filling loop assembly consisting of an elbow shaped copper pipe, isolation valve and double check valve assembly (which incorporates an isolation valve), verified by test (suitable for backflow protection against fluid category 3). Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of T-type thermostatic mixing valves with DZR brass bodies. Temperature is pre-set under a fixed cap. The inlet adaptors incorporate single check valve cartridges (verified by test, suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
T-type thermostatic mixing valve with a DZR brass body. Temperature is pre-set under a fixed cap. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Multi-layer shower hose with a PVC inner hose, supplied with EPDM ‘O’-rings. Maximum operating temperature 60°C.
Range of thermal balancing valves with brass bodies and EPDM O-rings. The products also incorporates an analogue temperature gauge. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 90°C
Range of pre-set pressure relief valves (spring loaded) with DZR brass body. Model SRV0353SW0475 is set at 4.75 bar, SRV0350SW060 is set at 6.0 bar and SRV03540505003 is set at 3.0 bar. Maximum operating temperature 85°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Activflo Lite range of water conditioners with copper bodies. Models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of filling loop assemblies, incorporating a stainless steel braided EPDM lined flexible hose, brass bodied isolation valve and a DZR brass non-verifiable double check valve assembly that incorporates an isolation valve. Model FL12041510 has a lanyard and end caps. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of spherical ball valves with single lever or T-handle operating members, brass bodies (nickel plated) and chromium plated brass ball and PTFE washers. Maximum working pressure = 40.0 bar. Maximum operating temperature 85.0°C
Range of full-bore spherical valves with a brass body (nickel plated), brass ball (chrome plated) and PTFE seats. All models are available as lever operated, 15-28mm sizes are also available with a butterfly handle. For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 25.0 bar. BS6920 85°C.
Range of full-bore spherical valves with a brass body (nickel plated), brass ball (chrome plated) and PTFE seats. All models are available as lever operated, 15-28mm sizes are also available with a butterfly handle. For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 25.0 bar. BS6920 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (plated?) with isolation valve & Strainer. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Wall mounted, thermostatic shower valve, (brass body – chrome plated), incorporating a single sequential headwork with a single lever operating member. The inlet elbows incorporate key operated spherical valves with chrome plated brass balls, PTFE seats and approved single check vlave cartridges, however, the complete product has not been fully tested to demonstrate backflow protection. To be used with copper pipe only – Standard EN 1057 Maximum working pressure 5 Bar. Maximum operating temperature 65°C
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
