Range of bronze bodied pre-set pressure relief valves (available between 0.2-16 bar on each model) incorporating a manually operated easing gear with brass seat and PTFE or EPDM washers.
Non-metallic materials and components comply with BS6920 at 85°C
Range of bronze bodied pre-set pressure relief valves (available between 0.2-16 bar on each model) incorporating a manually operated easing gear with brass seat and PTFE or EPDM washers. Maximum operating temperature 85°C.
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chromium plated brass balls and PTFE seats with lever, lockshield or T-type operating members. Maximum working pressures: 22mm – 28mm = 32.0 bar and 42mm – 54mm = 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a brass body and ball (brushed chrome plated), and PTFE seals. Maximum working pressure 42.0 bar (¼”, 3/8”, ½”, ¾” models) Maximum working pressure 32.0 bar (1”, 1 ¼”, 1 ½”, 2” models) Maximum working pressure 28.0 bar (2 ½” model) Maximum working pressure 16.0 bar (3” & 4” models) Maximum operating temperature 85°C
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Combined spherical valve and strainer with a brushed chromium plated brass body and stainless-steel filter. The strainer incorporates single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of quarter turn PVC-U double union spherical valves with EPDM seals and PTFE Seats. Maximum working pressure 16.0 bar. Cold water use only
Range of gate valves incorporating brass bodies, brass wedge, PTFE and NBR washers and operated via a non-rising spindle headwork. Maximum operating pressure 10.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies and PTFE seals. The valves incorporate a non-rising stem and hand-wheel or lock shield operating members (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 100ºC.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Screw down stop valve incorporating brass body and EPDM ‘O’-rings and hexagonal key operating member. Maximum working pressure 10.0 bar. Cold water use only.
Range of stop valves with brass bodies and an EPDM washer. 15mm and 22mm for use with half-hard copper pipe of R250 acc. to EN1057. 20mm and 25mm for use with half hard copper pipe of R250 acc. to BS2871-2. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'Cage Overmould 214867'. Black coloured, injection moulded ABS component. For use with water up to 70°C.
'Promag'. Factory applied, black coloured (once mixed), polyurethane primer and topcoat manufactured in Suzhou, China. Mix components A & B of the primer in a 1:2 mass ratio and apply as per manufacturer's instructions dated '13-01-2022' Cure for 2 hours@23°C. Mix components A, B & C of the topcoat in a 92.59%:5.19%:2.22% volume ratio and apply as per manufacturer's instructions dated '13-01-2022'. Cure for 20 seconds@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relipoxy 342 Food Grade Epoxy Coating'. Factory applied, brown-red coloured epoxy coating. Apply as per manufacturer's 'Standard Operating Procedure & Guidelines' issue number '116/2021' dated 15th Feb 2021. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoguard SF 157'. Factory applied, grey coloured, two-component epoxy coating. Mix in a 3:1 volume ratio. Apply as per manufacturer's Application Guidelines 'APPPG/SF157/001' dated 'Jan-2021'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`3M™ Scotchkote™ Fusion-Bonded Epoxy Coating 134`. Factory applied, green coloured, epoxy coating. Pre-heat substrate to 232°C, before dip coating as per manufacturer’s data sheet and application guide ‘78-8141-8528-2 Rev A’ dated February 2016, for 3 seconds. Cure for 10 minutes at 232°C. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cementitious Coating 851 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '851 /031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 89 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
