'Toyolac 700-314'. Beige coloured, injection moulded ABS material. For use with water up to 23°C.
'81661723' washers. Black coloured, resin impregnated carbon graphite washer components manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'D-1375-077'. Grey coloured, resin impregnated carbon graphite washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'H-3500-6351-9221'. Grey coloured silicon carbide washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'PGS3'. Grey coloured, compression moulded, Silicon Carbide, ring shaped seal/washer. For use with water up to 85°C.
'Angel Guard Ceramsafe 777'. White coloured, machined, ceramic material. For use with water up to 85°C.
'JIZJ-1'. Factory applied, light grey coloured Portland cement mortar. Mix cement, sand and water in a ratio of 1:1.7:0.55. Cure for 5 hours and 30 minutes@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HSXX CM-1'. Factory applied, grey coloured cement mortar. Mix, apply and cure as per manufacturer's Technical Data Sheet issue number '001' dated '2020.08.01'. For use with water up to 65°C.
'KOPATCH PC300-D/BLUE'. Factory applied, two component, dark blue coloured epoxy resin coating. Mix parts A & B in a volume ratio of 2:1. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS dated '9 November 2015'. Cure for 210 seconds@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET #1600 Gray F'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer`s instructions ref. no. '20210216-1' dated 2021/2/16. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions issued March 2017, V4.1. For use with water up to 85°C.
'EP-621'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions file no: 'TJR-QM-CO-032', 'edition A1' dated '2021-Feb.-26th'. For use with water up to 65°C.
'HEMPADUR 35600 Cream and Red'. Factory applied, cream or red coloured (when mixed), two-component epoxy coatings consisting of a base and curing agent. Mix the base and curing agent in a 14.8:5.2 volume ratio. Cure for 8 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS '20200801 A1'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fastfill'. Site applied, grey coloured cementitous mortar. Mix Fastfill and water in a 7.14:1 mass ratio. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4807'. Site applied, grey coloured cementitious repair mortar. Mix 'Intercrete 4807' and water in a mass ratio of 9.4:1 Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Fernox Powerflow Flux`. White coloured paste flux. For use with water up to 85°C.
'Korvan GRP Panel'. Cream coloured GRP panel manufactured by hot press moulding. For use with water up to 45°C.
'TBX 500'. Triple layered, extruded hose comprising of a white coloured, translucent TPE inner layer, black coloured PVC middle layer and grey coloured PVC outer layer. For use with water up to 23°C.
'IKV Tribostar SSI 1203TF/IKV Tribofood SSI 1203TF'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Bluesil Paste 408'. White coloured, translucent silicone paste lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
‘Tecomid NA40 GR30 BK005 HS QW, Tecomid NA40 GR35 BK005 HS QW, Tecomid NA40 GR40 BK005 HS QW, Tecomid NA40 GR45 BK005 HS QW & Tecomid NA40 GR50 BK005 HS QW’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Celanyl A3 WR GF30 BK 9005/Z/FA'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'Badamid B70 GF40 UV WL Black'. Black coloured, injection moulded, glass filled PA6 material. For use with water up to 65°C.
'PA66+50%GF 1620G50 BK015'. Black coloured, injection moulded PA66 (with 50% glass fibre) material. For use with water up to 85°C.
‘ELGEF PE-100 electrofusion fittings’, Black coloured, injection moulded polyethylene electrofusion fittings. For use with water up to 65°C.
'Popular HDPE Pipe'. Black coloured (blue external stripes), extruded HDPE pipe. For use with water up to 60°C.
'Lasertec Multilayer Compound Pipes (White)'. Extruded PE-RT/Al/PE-RT pipe comprising of a black coloured, PE-RT Type 2 inner layer, aluminium outer layer and white coloured PE-RT outer layer. For use with water up to 70°C.
'Unidelta Flexall'. Extruded, PE-RT/Al/PE-RT pipe comprising of white coloured (translucent) inner layer, aluminum middle later and white coloured (opaque) outer layer. For use with water up to 85°C.
'3301 black (330160415BLK)'. '3301 black (330130415BLK)' was added to the approval in November 2023. Black coloured, single sided polyethylene foam tapes with acrylic adhesive system. For use with water up to 23°C.
'TP10847 Prisma Black'. Black coloured polyethylene material manufacture by rotational moulding. For use with water up to 70°C.
`Revolve N-525 (6056) Natural (appears white coloured) & BH3239 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
`Revolve N-650/6068 Natural (appears cream coloured) & M-668 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
'Revolve 6405U Natural (appears white coloured) & Revolve M-1585 Black (black coloured)'. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
'Revolve N-307 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'XYRON WG732 AWY2266, WG732 AWY2269, WG732 AWY6628, WG722 AWY6627, W5002 AWY1208, W5002 AWY2267, W5002 AWY6629, W5002 AWY3326, WG722 AWY2261, WG732 AWY3325, WG722 AWY3324 & WG733 ABY3315'. Injection moulded, black, grey or beige coloured PPE materials manufactured in Thailand & China. For use with water up to 85°C.
‘Tecomid HT NT40 GR30 BK009 01 QW, Tecomid HT NT40 GR35 BK009 01 QW, Tecomid HT NT40 GR40 BK009 01 QW, Tecomid HT NT40 GR45 BK009 01 QW, Tecomid HT NT40 GR50 BK009 01 QW, Tecomid HT NT40 GR55 BK009 01 QW & Tecomid HT NT40 GR60 BK009 01 QW’. Black coloured, injection moulded glass-fibre reinforced PPA materials. For use with water up to 85°C.
'Popular PPRC 100 Pipe'. Green coloured, extruded PPR pipe. For use with water up to 60°C.
'Hostalen PP H5416T'. White coloured (translucent), extruded polypropylene material. For use with water up to 60°C.
`USW-85`. Black coloured, injection moulded TPU material. For use with water up to 23°C.
'George Fischer PVC-U Inch Pipe'. Grey coloured, extruded PVC-U pipe. For use with water up to 23°C.
'TP PVC-U Inch Pipe'. Grey coloured, extruded PVC-U pipe. For use with water up to 23°C.
'Kraken Black, White & Clear'. Cured, self-fusing, silicone rubber repair tape. For use with water up to 23°C.
`Superfast Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PX70N-0201 washers, ‘O’ rings, bushes gaskets & discs’. Black coloured, injection moulded EPDM components with a shore hardness of 70. The washers have a tested in-radius size of 3.0mm. The ‘O’ rings have a tested in-radius size of 3.5mm. The bushes gaskets have a tested in-radius size of 2.0mm. The discs have a tested in-radius size of 2.65mm. All are for use with water up to 85°C.
'60 EPDM 334 black 60 ShA' (shore hardness 60) and '70 EPDM 335 black 70 ShA' (shore hardness 70). Black coloured compression moulded EPDM materials. Tested in-radius 1.07mm. For use with water up to 85°C.
Page 5 of 71
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
