Range of deck mounted, flow control valves (brass bodies), incorporating a quarter turn ceramic disc headwork with either a cross top or single lever operating member (see models). The products are supplied with a metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
In-line adjustable pressure reducing valve assembly with a DZR brass body. The assembly also incorporates a stainless strainer (part of the pressure reducing valve), a spherical valve with a brass ball on the inlet, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) on the outlet, and a drain port with a brass plug. The product also includes a port with a plastic plug to accommodate a gauge/sensor (not supplied). Adjustable outlet pressure range between 1.0 and 6.0 bar. Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of latching and non-latching solenoid valves with brass bodies and an integral stainless-steel strainer. X262513141 (abc) (dd) models have a NBR ‘O’-Ring and diaphragm, all other models have an EPDM ‘O’-Ring and diaphragm. Maximum working pressure: see model. Maximum operating temperatures: X262513141(abc)(dd) models 65°C, all other models 85°C.
Solenoid valve incorporating a plastic body and an EPDM diaphragm. The product incorporates a plastic flow regulator with an EPDM washer, and a plastic filter on the inlet. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Range of in-line, “T” type or angled spherical valves incorporating brass bodies and brass ball, EPDM ‘O’-rings/Washers, PTFE seats and single lever or butterfly lever operating members. Some models incorporate port or pressure gauge. Models 0516/03DCVR1, 0516/03DCVR2 & 0516/04TR1 incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressures 10.0 bar Maximum operating temperature 100°C.
Range of brass bodied, straight and angled two and three-port spherical valves. Some models incorporate a screw-down pattern drain valve. Products incorporate a chrome-plated brass ball and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (nickel plated) brass bodies with single lever operating members, (chromium plated) brass ball and PTFE seat. Maximum working pressure 40.0 bar (Models 124-1027 CST, 124-1028 CST and 124-1029 CST) Maximum working pressure 25.0 bar (Models 124-1030 CST and 124-1031 CST) Maximum working pressure 16.0 bar (Models 124-1032 CST and 124-1033 CST) Maximum operating temperature 85°C.
Range of angled isolation ball valves incorporating brushed chrome plated DZR brass bodies, DZR brass ball (chrome plated), stainless steel strainer and approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves incorporating brass bodies, brass wedge, PTFE and NBR washers and operated via a non-rising spindle headwork. Maximum operating pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stop valves with brass bodies and an EPDM washer. 15mm and 22mm for use with half-hard copper pipe of R250 acc. to EN1057. 20mm and 25mm for use with half hard copper pipe of R250 acc. to BS2871-2. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Angle valve (chrome plated brass body), incorporating NBR rubber seals and a dome type operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of polyphosphate scale inhibitors comprising of an inline (nickel plated) brass body and head, and a separate cartridge with an aluminium body and plastic cap. Maximum working pressure 5.0 bar. Cold water use only.
Range of electrolytic scale reducers, with a chromium plated copper body and zinc alloy anodes. Maximum working pressure 5.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'CY25C & MAT4000'. Grey coloured, phenolic impregnated carbon washers. For use with water up to 85°C.
`CY9198`. Grey coloured, pressed and kilned carbon/graphite thrust ring. For use with water up to 85°C.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 6070'. Factory applied, black coloured, electrodeposition coating. Apply and cure as per technical data sheet ‘LT/F-16-128’ dated October 20th 2016. For use with water up to 23°C.
'Flogul® 645 Vert 6013'. Factory applied, green coloured paint. Apply as per manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rivertex® APO850 Blue & NTP™ E850 0A’ and ‘Rivertex® APO850 Grey & & NTP™ E850 0A '. Polyester fabric (NTP™ E850 0A) completely coated with blue or grey coloured polyolefin (Rivertex®), manufactured by extrusion coating. For use with water up to 23°C.
'novapress® 850'. Light brown coloured, compressed fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
`Vulkanite Bio`. Red coloured, compressed fibre gasket material. For use with water up to 65°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘UNITEC® Öko’. Green coloured, compressed fibre material (bound with NBR), manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'FlatSeal HMF17'. Light brown coloured, compressed fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'DualPac 2212 High Performance Multi-Purpose Packing'. Braided gland packing which is half white coloured and half yellow coloured. For use with water up to 85°C. For use as a gland packing only having been tested at a reduced surface area to volume ratio.
'Norsodyne H 13212 TAE Laminate' for use with 'Polycor White Gel Coat'. ‘NORSODYNE H 13212 BTAE Laminate' was added to the approval in July 2024. The glass fibre panel is manufactured by hand lay method and then factory applied, unsaturated resin gel coat is applied by brush (BR) or spray (PA). The brush gel coat is to be applied as per manufacturer's TDS ‘4100’ dated 10.10.17 and cured for 24 hours@25°C. The spray gel coat is to be applied as per manufacturer's TDS ‘4200’ dated 10.10.17 and cured for 24 hours@25°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Keyu Magnet'. Black coloured, pressed and sintered magnets. For use with water up to 85°C.
'UBE NYLON 1015GC350'. Black coloured, injection moulded PA material. For use with water up to 23°C.
'EcoPaXX® Q-DWX6 BK00002 & EcoPaXX® Q-DWX10 BK00002’ (black coloured). 'EcoPaXX® Q-DWX6 NA99001 & EcoPaXX® Q-DWX10 NA99001’ (natural – appears beige). Injection moulded polyamide materials. For use with water up to 85°C.
'Green Pipes HDPE Pipes'. Black coloured (with blue external stripe), extruded HDPE pipe. For use with water up to 65°C.
'Green Pipes HDPE Fittings'. Black coloured (with blue external stripe), fabricated butt-fusion HDPE fittings. For use with water up to 65°C.
'PF Press'. Triple layered, extruded pipe comprising of a white coloured (translucent) inner layer, aluminium middle layer and white coloured (opaque) outer layer. For use with water up to 85°C.
'XD PE Fitting'. Black coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'+GF+ Aquasystem PPR Pipe'. Extruded PPR pipes which are either green coloured (with blue stripes) or grey coloured (with red stripe). For use with water up to 70°C.
'+GF+ Aquasystem PPR Fittings'. Injection moulded PPR fittings which are either green coloured or grey coloured. For use with water up to 70°C.
'iJoint'. Black coloured, injection moulded polypropylene fitting. For use with water up to 60°C.
'Aidmer78-031'. White coloured (opaque), extruded PTFE pipe. For use with water up to 85°C.
`TL-KN-006`. Black coloured, compression moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 1.1mm. For use with water up to 23°C.
'Sunaflex T 8289'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'LC 50-90'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.33mm. For use with water up to 85°C.
'Sunaflex T 8157'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Athena-EPDM-XX70'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.33mm. For use with water up to 85°C.
Page 33 of 71
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
