Range of combination valves consisting of an in-line adjustable pressure reducing valve (between 1.5 and 6.0 bar) and a pressure relief valve, with DZR Brass bodies, EPDM `O`-rings and an EPDM diaphragm. CWIC110004 model - Pressure reducing valve pre-set at 3.5 bar and pressure relief valve set at 6.0 bar. CWIC200055 model - Pressure reducing valve pre-set at 3.0 bar and pressure relief valve set at 4.5 bar. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum supply pressure 16.0 bar. Outlet pressure range 1.5 bar to 6.0 bar (both models). Maximum operating temperature 20°C.
‘DEWALT PV60-PRO’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1, version 16/01/2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled via a manual operating single lever on body. The inlets hose incorporates stainless steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection). The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) electronically controlled combination tap assemblies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor and the temperature set via a manual lever. The inlet adaptor to the hoses incorporates a check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2 or 3) with a built-in strainer, and the outlet incorporates an aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of inlet control valves with DZR brass bodies incorporating a pressure reducing valve (set at 1.5, 1.8. 2.0, 2.1, 3.0 or 3.5 depending on model) and a pressure relief valve (set at 3.0, 3.5, 4.5, 5.0. 6.0 or 8.0 depending on model. All models incorporate a stainless-steel mesh and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model CWIC355040 comes supplied with a tundish. For use with copper pipe to BS EN 1057, PB pipe (with inserts) to BS EN 7291-2:2010 and PEX pipe (with inserts) to BS EN 7291-3:2010. Maximum working pressure 16.0. Maximum operating temperature of 25°C.
Range of basin bidet mixers with brass bodies, incorporating a ceramic cartridge headwork, and a single lever operating member. The spout incorporates a plastic aerator within a swivel nozzle. This product is supplied with a lever type pop up waste (not tested). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of ceramic cartridges with plastic bodies for insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of ceramic cartridges or 2-way ceramic disc diverter headworks with plastic bodies, EPDM ‘O’-rings and/or gaskets, for insertion into specifically dimensioned bores. The JA01AJ and AH01AJ models incorporate a thermostatic element. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridges with plastic bodies, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Thermostatic cartridge with brass body for insertion into specifically dimensioned bores Maximum operating temperature 85°C
Thermostatic cartridges with plastic bodies, stainless steel mesh strainer and EPDM ‘O’ rings. For insertion into specifically dimensioned bores. Maximum operating pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole single outlet fixed combination tap assemblies, (chrome plated brass), incorporating quarter turn ceramic disc headworks with a single lever operating member and non-rising spindle headwork with a variety of operating members (See models) controlling the flow to the additional swivel spout. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). The inlets incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the swivel spouts incorporates plastic aerators. These products are supplied with metal back nuts. Maximum working pressure 8.6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole single outlet fixed combination tap assemblies, (chrome plated brass), incorporating a quarter turn ceramic disc headwork with a single lever operating member and non-rising spindle headwork with a variety of operating members (See models) controlling the flow to the additional swivel spout. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). The inlets incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the swivel spouts incorporates plastic aerators. Maximum working pressure 8.6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating either quarter turn ceramic disc or quarter turn compression washer headworks with various operating members (see model). The inlets of the quarter turn ceramic disc headworks incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model). The product is supplied with metal backnuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc or a quarter turn compression washer headwork with various operating members (see model). The inlet of the quarter turn ceramic disc headwork incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model). The product is supplied with metal backnuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating ceramic cartridge headworks with single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers. Models 5059340452869 have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated) and pull-out spray. The products incorporate a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination taps assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks with joystick operating members. The spout outlets incorporate plastic aerators. Models are supplied with lever operated pop-up waste (excluding 31 018 xxx). Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. All models are supplied with a pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model 193838EX,193838EX MBK1, 163838EX & 163838EX MBK1 is only supplied with an aerator) . The product is supplied with a click type waste (verified by test). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated bodies), incorporating ceramic cartridge headworks with single lever operating members. The products are supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Single-hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet, fixed, combination tap assemblies (brass bodies - various finishes ) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied either with or without a lever type pop-up waste set (see models). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating detent (push to open, push to close) type headworks controlling both temperature and flow with a dome operating member. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a lever type pop up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a detent (push to open and push to close) ceramic cartridge headworks, and cube type operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers and a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with a click type pop up waste. Maximum working pressure 10.0 Bar.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The inlets of 2621 models incorporate plastic strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets of 26216 models incorporate single check valve cartridge assembly (suitable for backflow protection against fluid category 2), plastic strainers and a single lever operated spherical valves. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly (brass bodies - various finishes). Incorporating ceramic cartridge headworks, and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type pop-up waste or lever type pop up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The products are supplied with a click type pop-up waste verified by test. Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of deck mounted, single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headworks and various type operating members (see models). The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with a metal back nut. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Single-hole, single outlet, fixed, combination tap assembly, (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type pop-up waste. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly (brass body – various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, metal, single outlet (fixed) combination taps assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with a lever type pop-up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of single hole, single outlet (fixed), combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever type pop up waste. Model (71252xxx) supplied with click type pop-up waste (not verified by test). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed combination tap assemblies, (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with various - operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Between May 2023 and July 2023, the taps have a maximum operating temperature of 65°C. From August 2023 the taps have a maximum operating temperature of 60°C.
Range of floor mounted, single hole, single outlet fixed combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self- cancelling diverter to shower outlet. This spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly, (brass body - various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass body), incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 27 of 56
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
