Range of pressure relief valves pre-set at 3.0 bar with brass bodies and a EPDM membrane. Valve incorporates a manually operated easing gear. Maximum operating temperature 85°C.
Range of solenoid valves with a plastic body and an EPDM diaphragm. Available as either inline (126 suffix models) or 90° outlet (115 suffix models). The inlet of the existing 62.009.115 (¾” BSP (M) inlet x ⅜” BSP (M) outlet) model incorporates a plastic strainer and a plastic flow regulator. The products are also supplied with an optional stainless-steel strainer for installation on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperatures: Existing model 62.009.115: ¾” BSP (M) inlet x ⅜” BSP (M) outlet: 90°C. Models added November 2023: Cold water use only. From March 2025 all models: 90°C.
Range of screwdriver operated servicing valves incorporating brass bodies and chromium plated brass ball, nylon seats and EPDM seals. Maximum working pressure 7.0 bar. Maximum operating temperature 99°C.
Range of spherical valves with DZR brass bodies, chromium plated brass balls and PTFE seats with lever, lockshield or T-type operating members. Maximum working pressures: 22mm – 28mm = 32.0 bar and 42mm – 54mm = 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a brass body and ball (brushed chrome plated), and PTFE seals. Maximum working pressure 42.0 bar (¼”, 3/8”, ½”, ¾” models) Maximum working pressure 32.0 bar (1”, 1 ¼”, 1 ½”, 2” models) Maximum working pressure 28.0 bar (2 ½” model) Maximum working pressure 16.0 bar (3” & 4” models) Maximum operating temperature 85°C
Combined spherical valve and strainer with a brushed chromium plated brass body and stainless-steel filter. The strainer incorporates single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
A range of screwdriver operated spherical valves with brass bodies and brass ball, EDPM ‘O’-rings and fibre washers. Maximum working pressure 16.0 bar, Maximum working temperature 85°C.
Range of inline and angled screwdriver or lever handle operated spherical valves with (chromium plated) brass bodies, chromium plated brass ball, NBR ‘O’-rings. For use with copper pipe manufactured to EN 1057 Maximum working pressure 16.0 bar at 30°C and 5 bar at 99°C Maximum working pressure 6.0 bar. Maximum operating temperature 90°C (model TX480 only)
Range of quarter turn PVC-U double union spherical valves with EPDM seals and PTFE Seats. Maximum working pressure 16.0 bar. Cold water use only
Range of gate valves incorporating brass bodies, brass wedge, PTFE and NBR washers and operated via a non-rising spindle headwork. Maximum operating pressure 10.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies and PTFE seals. The valves incorporate a non-rising stem and hand-wheel or lock shield operating members (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 100ºC.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
'Promag'. Factory applied, black coloured (once mixed), polyurethane primer and topcoat manufactured in Suzhou, China. Mix components A & B of the primer in a 1:2 mass ratio and apply as per manufacturer's instructions dated '13-01-2022' Cure for 2 hours@23°C. Mix components A, B & C of the topcoat in a 92.59%:5.19%:2.22% volume ratio and apply as per manufacturer's instructions dated '13-01-2022'. Cure for 20 seconds@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V- SRPC Portland Cement'. Factory applied, grey coloured Portland Cement. Mixx Sand:water:cement in a weight ratio of 0.6:1.0:0.22. Cure for 96 hours@26°C and then 576 hours@32°C. For use with water up to 65°C.
'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. The following grades are manufactured at GERMANY, REUTLINGEN: Resicoat R4 blue: R4-ES HJ601R, R4-ES HJ605R, R4-ES HJ606R, R4-FB HJC04R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC12R, R4-FB HJC33R, R4-FB HJC34R, R4-FB HJC36R, R4-ES HJF01R, R4-ES HJF09R, R4-ES HJF10R, R4-ES HJF13R PAM blue, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF23R, R4-ES HJF24R, R4-ES HJF26R, R4-ES HJF42R, R4-ES HJG05R, R4-ES HJG07R, R4-ES HJG08R, R4-ES HJH01R & R4-FB HJC26R. Resicoat R4 red/red-brown: R4-FB HGC07R, R4-FB HGC17R, R4-ES HGF03R, R4-ES HGF04R, R4-ES HGF10R, R4-ES HGF17R, R4-ES HGF20R, R4-ES HGH02R. Resicoat R4 black: R4-ES HNF04R & R4-FB HNC01R. Resicoat R4 green: R4-FB HKC71R. Resicoat R8 blue: R8-ES HJF97R, R8-FB HJC37R, R8-FB HJC38R, R8-ES HJG13R, R8-FB HJC50R, R8-FB HJC51R, R8-FB HJC52R, R8-FB HJC53R, R8-FB HJC54R, R8-ES HJF1KR, R8-ES HJF2KR, R8-ES HJF3KR, R8-ES HJF4KR, R8-ES HJF5KR, R8-ES HJF6KR, R8-ES HJG29R & R8-ES HJ609R. Resicoat R8 blue grades added in July 2024: R8-FB HJC55R, R8-ES HJF4MR & R8-ES HJF5LR. Resicoat R8 red/red-brown: R8-FB HGC12R, R8-ES HGF66R, R8-ES HGF67R & R8-ES HGF68R. Resicoat R8 red added in February 2025: R8-ES HGF65R. Resicoat R8 black: R8-ES HNC03R & R8-ES HNF43R. Resicoat R2 blue: R2-ES HJF5BR & R2-ES HJF4ER. The following grades are manufactured at USA, NASHVILLE: Resicoat R4 blue: R4-ES HJ606R, R4-ES HJF10R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-FB HGC17R & R4-ES HGF17R. Resicoat R4 green: R4-ES HKF47R. The following grades are manufactured at CHANGZHOU, CHINA: Resicoat R2 blue: R2-ES HJF5BR. Resicoat R4 blue: R4-FB HJC03R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC15R, R4-FB HJC23R, R4-FB HJC29R, R4-ES HJF01R, R4-ES HJF10R, R4-ES HJF13R, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-ES HGF03R, R4-ES HGF04R & R4-ES HGF17R. Resicoat R4 black: R4-ES HNF04R. Resicoat R8 blue grades added in February 2025: R8-FB HJC50R, R8-ES HJF3KR, R8-ES HJF97R The following grades are manufactured at IZMIR, TURKEY: Resicoat R2 blue: R2-ES HJF3D4 & R2-ES HJF4D4. Resicoat R4 blue: R4-ES HJF1C4 & R4-ES HJF2C4. Resicoat R8 blue added in February 2025: R8-ES HJF5M4 The following grades are manufactured at THANE, INDIA: Resicoat R2 blue: R2 HJC43N, R2 HJF2HN, R2 HJF5BR. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Polyurea FA 1044'. Factory applied, two-component, beige coloured polyurea coating. Mix parts A and B in a 1:1 volume ratio apply as per manufacturer's TDS '07/2015 Rev.00'. Cure for 96 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PVEF undercoat with Fluiglide Topcoat’. Factory applied, cream coloured (once mixed and applied), coating system comprising of ‘Polyglass VEF’, two-component glassflake vinyl ester undercoat and ‘Fluiglide’, two-component polyester topcoat. Mix and apply ‘Polyglass VEF’ in accordance with Corrocoat ‘product reference 2/23’ dated ‘5th June 2007’ and last reviewed ‘March 2022’. Cure for 24 hrs@20°C (±1°C). Mix and apply ‘Fluiglide’ in accordance with Corrocoat ‘product reference ‘4/01’, valid from ‘23rd October 1995’ and last reviewed ‘March 2022’. Cure for a minimum of 6 days@20°C (with a lower tolerance of -1°C). These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Interline 925GF (White)'. Site applied, white coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (off-white liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions '2253' dated 29/11/2011. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White'. Site applied, two-component, white coloured epoxy coating. Mix part A (off-white white coloured liquid) and part B (off-white coloured liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions ref. '2252', issue date 17/12/2020. Cure for 7 days@25°C. Between January 2022 and August 2022, the coating was for use with water up to 23°C. Between September 2022 and January 2027, the coating is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LATTYflon 4789'. Yellow coloured, braided fibre/PTFE gland packing. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Aropol M 105 TA WRAS’ (formerly known as ‘Aropol M 105 TA’) & ‘Enguard GE NTRL HH WRAS’ (formerly known as ‘Enguard GE NTRL HH'): Translucent straw coloured (glossy one side textured the other), polyester laminating resin manufactured by hand lay-up & gelcoat (brush applied), sheet material. ‘Aropol M 105 TAXR’ & ‘Enguard GE WHI S WRAS’ (formerly known as ‘Enguard GE WHI S’): White coloured (glossy) on one side, translucent straw coloured (textured on the other), polyester laminating resin manufactured by hand lay-up & gelcoat (spray applied), sheet material. Apply as per Ineos Composites method statement ‘Preparation of laminated products for freshwater applications (WRAS)’, ‘code R071, edition 2’ dated 19.1.22. Cure for 9 hours at 23°C with 2% of MEKP-50 catalyst, post-cure for 24 hours@50°C and wash part thoroughly in water before use. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S350 Silicone Fluid'. Colourless (transparent) silicone lubricant. Apply as per manufacturer's instructions for use 'LDAP-009', issue 1 dated May 2021. For use with water up to 85°C.
'Turbine Overmould 208399'. Black coloured, injection moulded, strontium ferrite filled nylon 6 component. For use with water up to 70°C.
'Zytel® RSFG30G50L BK595'. Black coloured, injection moulded glass fibre reinforced nylon (polyamide 610) material. For use with water up to 85°C.
'Zytel® FG70G30HSR3 BK309'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
`Grilamid TR 90 LS Natural & Grilamid TR 90 Natural`. Natural (colourless, transparent), injection moulded nylon materials. For use with water up to 85°C.
'4MID 9B22130 W-A BNL100'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Genestar™ G1500D-L47WF BLACK'. Black coloured, injection moulded or extruded Polyamide 9T material. For use with water up to 85°C.
'Akoalit PB R 539'. Natural (which appears white coloured), compression moulded polybutylene material. For use with water up to 85°C.
'Sirogel 9000 (beige coloured) & Sirogel 9100 (white coloured)'. Manually injection moulded polyester resins. For use with water up to 45°C.
‘Kingbull PE100 blue pipe (391721)'. Blue coloured, extruded polyethylene pipe. ‘Kingbull PE100 black pipe’ (0103102). Black coloured (with external blue stripe), extruded polyethylene pipe. Both for use with water up to 65°C.
'K9'. White coloured, extruded polyethylene pipe. For use with water up to 85°C.
‘Kingbull PE100 blue pipe (391721)'. Blue coloured, extruded polyethylene pipe. ‘Kingbull PE100 black pipe’ (0103102). Black coloured (with external blue stripe), extruded polyethylene pipe. Both for use with water up to 65°C.
'HDPE 100 Black POLIMAXX P901BK'. Black coloured, extruded HDPE pipe. For use with water up to 65°C.
'HDPE 100 Blue POLIMAXX P901BL'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'Isoryl A 20 90 GF20 W NA'. Beige coloured, injection moulded PPO material. For use with water up to 85°C.
'9711/2 Black'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radii sizes between 0.88mm & 2.85mm. Between October 2021 and July 2022, the components were for use with water up to 23°C. Between August 2022 and October 2026, the components are for use with water up to 85°C.
'EWDRI 50, EWDRI 55, EWDRI 60, EWDRI 65, EWDRI 70 & EWDRI 80'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 0.69mm. 'EWDRI 50' is for use with water up to 70°C. 'EWDRI 55, EWDRI 60, EWDRI 65, EWDRI 70 & EWDRI 80' are for use with water up to 60°C.
'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
'7PD1612 washers'. Black coloured, extruded NBR rubber washers. Tested in-radius size 1.4mm. Shore hardness 70. '7PD1612 'O' rings'. Black coloured, injection moulded NBR rubber `O` rings. Tested in-radius size 0.9mm. Shore hardness 70. Both for use with water up to 60°C.
'Tangit PVC-U Plus'. Light yellow (straw) coloured, solvent cement. Apply as per manufacturer's TDS 'Tangit PVC-U PLUS TDS 070917 EN'. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
A range of single-hole, single outlet (fixed (model 62816) or swivel (models 63407)) electronically controlled tap assemblies with brass bodies in various finishes (see models). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating members controlling both the flow and temperature for all models excluding 62816, which uses a mixer to control the temperature only with a single lever operating member. The spout outlets incorporate plastic aerators. All models (excluding 63407) incorporate a separate approved check valve cartridge on the inlet, verified by test (suitable for backflow protection against Fluid Category 2), The inlets of all models incorporate stainless steel strainers. Maximum working pressure 5.0 bar Maximum working temperature 60°C.
Single-hole, single outlet, swivel electronically controlled tap assembly with a brass body in various finishes (see model). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating member controlling both the flow and temperature. The spout outlet incorporates a pull-out spray with a plastic aerator. The inlets incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2), and a stainless-steel strainer Maximum working pressure 5 bar. Maximum working temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres and incorporates a servicing valve and flexible hose on the inlet supply.The cistern is operated by a pnuematic push button Maximum working pressure 10.0 bar. Cold water use only.
Page 20 of 83
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
