Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'REVIMEN Bituminous Paint'. Factory applied, black coloured Bituminous paint. Apply as per manufacturer's TDS/Application Application Method 'AM25001', issued 'March 5, 2025'. Cure for 8 hours@25°C at a relative humidity of less than 85%. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ResiGard APUA (NT) Coating'. Factory applied, grey coloured (once mixed), two-component coating. Mix and apply as per Technical Data Sheet ‘PDS/RG37/Ver15/01/25’. Cure for 1 minute@25°C. For use with water up to 85°C.
'Greentech 5000'. Factory applied, blue coloured Epoxy powder coating. Apply as per manufacturer's 'GRHK/QES GL 2025' and cure for 10 minutes@200°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PolyQuick® P-500 PW'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 05-2025'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'SOLID-196', 'Vision: A-2', dated '2019-8-28'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PA6059 Pure Polyester Powder Coating'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions 'file no. FP180515 version 2' dated May 25, 2018. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOD-E-2024/1'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions 'T264', revision '00', dated '16.07.2024'. Cure for 25 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TIANYI SUNS-011'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'Tianyi Suns-0023', version 'TYS-02', dated '2021-05-04'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Evercrete Vetrofluid'. Site applied, colourless, cement waterproofing liquid. Apply two coats as per manufacturer's instructions dated '01 JULY 2024'. Cure Coat 1 for 4hrs 40mins@21ºC and Coat 2 for 36 days@21ºC. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM AC'. Site applied, grey coloured cement mortar. Mix 'NATCEM AC' and water in a weight ratio of 5:1 and apply as per manufacturer's Instructions for Use 'Issue 4', dated '16 September 2024'. Cure for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'UNISILKON TK 002/1000'. Clear lubricant, to be applied as per manufacturer's instructions. For use with water up to 65°C.
'Sinopec Water Pipeline Joint Lubricant (Si) (product code: 509164)'. Clear, translucent silicone base lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'MS Schramberg Sintered Barium Ferrite (10-1176001)'. Dark grey coloured Sintered Barium Ferrite ring component. For use with water up to 85°C.
'MS Schramberg Sintered Strontium Ferrite (10-1173001)'. Grey coloured Sintered Strontium Ferrite ring component. For use with water up to 85°C.
'PLUSTEK PAT302PWG50BK10'. Black coloured, injection moulded, glass-fibre reinforced polyamide material. For use with water up to 85°C.
'ULTRAMID B3E2G6 AQUA GREY 7118'. Grey coloured, injection moulded PA6 material. For use with water up to 85°C.
'PB-1 Flexpipe (Grey)'. Grey coloured, extruded polybutylene pipe. For use with water up to 85°C.
'SCGC HDPE H112PC'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'Shield HDPE-100 Pipe' (extruded) and 'Shield HDPE-100 Fabricated Pipe' (extruded then fabricated). Black coloured, HDPE pipes. For use with water up to 85°C.
'Shield HDPE-100 Moulded Fittings'. Black coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'TEGA PE100-RC Blue fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'Techniplast PE100 Pipes'. Black coloured (with blue stripe), extruded PE100 pipes. For use with water up to 60°C.
'NORYL WM300G-701 (black), NORYL WM300G-960 (grey), NORYL WM300G-801 (beige) & NORYL WM300G-845 (beige)'. Injection moulded PPE+PS materials. For use with water up to 85°C.
'Noryl PX1630 – 73701'. Black coloured, injection moulded PPE material. For use with water up to 85°C.
'MD001 PPR Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 65°C.
'Hostalen PP H4122 103220'. Polypropylene material for injection moulding and compression moulding. For use with water up to 23°C.
'GW 160m'. White coloured (opaque), thread sealant. For use with water up to 85°C.
'Etinox F-A2002 0715'. Grey coloured U-PVC material for injection moulding and extrusion purposes. For use with water up to 23°C.
'B1-4651'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 60. Tested in-radius size 4.6mm. For use with water up to 23°C.
'E7001Z59-10 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70A. Tested in-radius size 1.85mm. For use with water 85°C.
'EP70 Black EPDM Diaphragm Seals'. Black coloured, compression moulded EPDM diaphragm seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘EP4118F, EP4518F, EP5118F, EP5518F, EP6118F, EP6518F, EP6512F (also known as EP6512P), E7008F, EP7118F, EP7518F, EP7068PF (added in April 2025), EP8018F, EP8118F, EP8518F & EP9118F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'Precision782628 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E633'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP011470P(KAWN)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'N8018AA'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LOCTITE® 6300™’. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘0.1’, dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
WC douche set including a trigger spray, flexible hose and wall outlet with stop lever. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
'XRRA 410B GR1500'. Grey coloured, injection moulded U-PVC material. For use with water up to 23°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Concealed WC dual flushing cisterns with a BS 1212- 4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a manually operated dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Floor standing, single hole, single outlet (fixed) combination tap assembly, (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3).The spout outlets incorporate plastic aerators. The shower outlet incorporates an approved single check valve cartridge, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (black or chrome plated brass). The flow is controlled via solenoid valve which is actuated by an infra-red sensor and the temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies, models AI-903215, Al-903222 & AI-903228 are chrome plated. Maximum working pressures: AI-903215, AI-903222 & AI-903020 16 bar. AI-903032, AI-903040 & AI-903050 10 bar. Maximum operating temperature 60°C Added September 2025 Maximum working pressure 10 Bar (AI-903025) Maximum working pressure 16 Bar (AI-903228) Maximum operating temperature 85°C
Range of non-rising spindle headworks with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 176 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
