Range of gate valves with blue epoxy coated cast iron bodies and EPDM coated cast iron wedges, operated via non-rising spindle. Maximum working pressure 10.0 bar and 16.0 bar (dependent on flange drilling pattern). Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedges and non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of double regulating valves incorporating bronze bodies with two test ports. Valves are adjusted using a handwheel. Maximum operating pressure: 25 bar. Maximum operating temperature: 85°C.
Range of magnetic, electrolytic or combined magnetic & electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
'(POM) MC90'. White coloured, injection moulded POM material. For use with water up to 85°C.
'LAC 500 MP5022'. White coloured (opaque), extruded ABS material. For use with water up to 23°C.
'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC5015 Sky Blue FBE'. Factory applied, blue coloured fusion bonded, epoxy powder coating. Pre-heat the surface to be coated to 200°C for 5 minutes and dip in a fluidised bed of powder coating as per manufacturer's data sheet 'VPC5015, revision 5' dated '25 January 2023'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaguard CSF 585'. Factory applied, light blue coloured two component epoxy coating consisting of a base and hardener. Mix base & hardener in a volume ratio of 77.5:22.5 and apply as manufacturer's Product Data Sheet '7785', revised May 31, 2022. Cure for 15 days@21°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV17'. Factory applied, blue coloured, two-component epoxy coating. Mix coating and hardener in a weight ratio of 4:1 or volume ratio of 3:1 and apply as per manufacturer's TDS '01 – 11.06.2024'. Cure for 7 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Truform Cement OPC 43 Grade'. Factory applied, grey coloured cement. Mix cement:sand in a weight ratio of 2:1 and add 0.5 litres of water. Apply as per manufacturer's instructions 'TTPL/SOP/MCD/03', revision '00', dated 01.04.2018. Cure for 24 hours@27°C followed by 7 days@85°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FiberTie Pipe Factory and Accessories W.L.L.GRE composite pipe'. GRE pipe which consists of a beige/yellow coloured inner layer and pale green coloured outer layer, manufactured by helical winding. For use with water up to 50°C.
'Purolite PFC 100E'. Brown coloured ion exchange resin. For use with water up to 85°C.
'Purolite C104EPLUS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'WACKER® AK 350'. Colourless, transparent lubricant. For use with water up to 60°C.
'Ultramid® D3EG12 Aqua BK102'. Black coloured, injection moulded polyamide material. For use with water 85°C.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
'Paryls PPA A6200GLXX' (XX denotes the weight percentage of glass fibre between 30% to 50%). Black coloured, glass fibre reinforced polyamide materials manufactured by twin screw extrusion. For use with water up to 85°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'Ultradur® B4520 FC Aqua uncolored'. Uncoloured (appears white), injection moulded PBT materials. For use with water up to 23°C.
'Ketaspire KT-820 GF30 BG20'. Brown coloured, injection moulded PEEK material. For use with water up to 85°C.
'DOKERLER HDPE fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Union Pipes Industry Fabricated Fittings'. Black coloured, extruded and welded, fabricated polytheylene fittings. For use with water up to 60°C.
'Kalson Polyethylene Pipe'. Blue coloured, extruded polyethylene pipe. For use with water up to 50°C.
'Ultrason® P 3010 Blau 80100'. Blue coloured, injection moulded PPSU material. For use with water up to 85°C.
'ISOMAG Cylinder'. Grey coloured, extruded polypropylene cylinder component. For use with water up to 60°C.
'Roxy PP-R pipe'. Green coloured, extruded PP-R pipe. For use with water up to 70°C.
'LATENE AG7H G/30 BLACK F:3352'. Black coloured, injection moulded PP material. For use with water up to 23°C.
'Ultrason® S 2010 G4'. Light beige coloured, injection moulded polysulphone material. For use with water up to 85°C
'662016, 662014, 662062 & 662061'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'IROGRAN® A 85 P 4441 FCM'. White coloured, injection moulded polyurethane material. For use with water up to 60°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'EPDM4570‐70'. Black coloured, compression moulded gaskets. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
'OR 70 EPDM 335 DW 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 1.77mm. For use with water up to 85°C.
'TIMO 3-70 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
‘TIMO 3-60 ‘O’ rings and gaskets’. Black coloured, injection moulded EPDM ‘O’ rings and gaskets. Shore hardness 60. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
'HT5557-20'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 60°C.
Page 173 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
