Range of lug type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs, EPDM seats and lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
2-way ceramic disc diverter with a plastic body, NBR ‘O’-rings and silicone seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Ceramic disc diverter cartridge incorporating a plastic body for use in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Wall mounted, concealed, 2-way diverter valve (brass body and chrome trim set) with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of ceramic disc type float operated inlet valves with DZR brass bodies. The valves discharge from a downwards atmospheric discharge arrangement on the upper part of the body. Maximum working pressure 5.0 bar. For cold water use only.
Range of wall mounted, concealed flow control valves with brass bodies, incorporating either one or two quarter turn ceramic disc headworks with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
‘Europress’ range of in-line pressure reducing valves, with DZR brass bodies and EPDM ‘O’-rings and washer. The outlet pressure is adjustable between 1.0 - 5.5 bar. Operating parameters: 2430012 EUROPRESS model: Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C. 2430034 EUROPRESS & 2430100 EUROPRESS models: Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 99°C.
Range of adjustable pressure reducing valves incorporating a plastic body and EPDM ‘O’-rings and stainless steel strainers. Outlet pressure 1.2 - 8.0 bar. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 85°C.
Manually adjustable pressure reducing valve, which incorporates a DZR brass body and an in-line double check valve assembly on the inlet (verified by test as suitable for backflow protection against Fluid Category 3). The outlet incorporates a shut-off valve. Maximum supply pressure 16.0 bar. Maximum outlet pressure between 1.5 bar and 6.0 bar. Maximum operating temperature 40°C.
‘EV220A-W’ range of normally closed solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Aquatsop leak detection system intended to shut the water supply in the event of a water leak. Consisting of two single normally closed servo controlled solenoid valves with a flow regulator and stainless steel filter at the inlet. A LDPE inner hose with corrugated plastic outer hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of latching and normally closed (see model) solenoid valves with plastic bodies, NBR diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
In-line spherical valve incorporating a nickel plated brass body, chromium plated brass ball, NBR rubber ‘O’-rings and single lever operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with bronze bodies, DZR brass ball (sizes ½” to 1”) and bronze ball (sizes 1 ¼” to 2”) PTFE seats and various operating member types (see models). Maximum working pressure: 25.0 bar. Maximum operating temperature: 85⁰C.
Range of servicing valves incorporating brass bodies (chrome plated or natural brass) The P2290 & P2290SI models are spherical valves with brass balls. The 201210 A-80 model is quarter turn with an EPDM seat and ‘O’-ring. The NF721 & NF721SI models are quarter turn with a NBR seat and EPDM ‘O’-ring. The 00711 A-80 is quarter turn with a NBR seat and ‘O’-rings. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating bronze bodies, wedges and a non-rising stem. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range OF JLA commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with three ¾” x ¾” BSP (F) double check valve assemblies (suitable for backflow protection against Fluid Category 3) for installation on each inlet prior to a HDPE inlet hose with ¾” x ¾” captive nut end connections. Maximum working pressure 5.7 Bar. Maximum operating temperature 60°C.
Range of commercial front loading, hood type & utensil washer type dishwashing machines with flow controlled by solenoid and discharged via type AB air gap (verified by test - suitable for backflow protection against fluid category 5) . The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
`Hy-MAG` range of electromagnetic water conditioners with blue PTFE coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of domestic, salt regenerated ion exchange water softeners. Maximum working pressure 6.0 bar. Cold water use only.
'Droople DRP-M90-IMP'. White coloured, injection moulded acetal cogwheel. For use with water up to 65°C.
'CarSIK-NT'. Grey coloured, RBSiC/SiSiC Reaction Bonded Silicon Carbide washer/seal ring, manufactured by isostatic pressing. For use with water up to 80°C.
'PS5000 Seal'. Grey coloured, compression moulded silicon carbide seal. For use with water up to 85°C.
'SYAL B950' (brown coloured) & 'SYAL A950' (white coloured). Dry press moulded ceramic materials. For use with water up to 85°C.
'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'42.5 (HSR)'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SW-02'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquafitting Blue'. Factory applied, blue coloured epoxy coating. Apply and cure as per manufacturer's instructions file number 'DLCHB-CO-001', edition 'A1', issue date '2021-April-11st'. For use with water up to 65°C.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOKIM Painting System'. Factory applied, dark green coloured (once top coat applied), two-component epoxy coating comprising of a primer and top coat. The primer (EPOX code A0768.N05133 + cat.A0918.N00100) consists of a catalyst and hardener which should be mixed in a 100:43 volume ratio before applying two coats in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 40 minutes@40°C. The top coat (EPOKIM HS code A0435.N02038 + cat.A0904.N00000) consists of a catalyst and hardener which should be mixed in a 100:16 volume ratio before applying one coat in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 10 minutes@20°C. The complete system should then be ‘stoved’ for 60 minutes@70°C. For use with water up to 23°C.
'DUAYEN E-39'. Factory applied, two-component, red coloured (once mixed) epoxy coating. Mix Parts A&B in a volume ratio of 79.5:20.5 and apply as per manufacturer's instructions '00.05102021'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 891.20 RACCORD'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet 'Doc. 087' (version dated 01/07/2011). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Belzona 1321`. Site applied, two-part, epoxy amine coating available in grey or blue colours. Mix base and hardener in a 11:1 mass ratio. Apply and cure as per manufacturer’s IFU ‘FN10026’, publication number ’02-09-21’. For use with water up to 23°C. These materials are only approved for the mixing conditions that appear on the approval. If the mixing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic®-6100 FX White’ (formerly known as ‘MasterSeal 6100 FX White’) ‘Sikalastic®-6100 FX Grey’ (formerly known as ‘MasterSeal 6100 FX Grey’. Site applied, two-component cementitious coating. Mix ‘Sikalastic®-6100 FX White’ (Coat 1) with water in a mass ratio of 15:5.6. Apply and cure for 1 day@5°C before applying Coat 2. Mix ‘Sikalastic®-6100 FX Grey’ (Coat 2) with water in a mass ratio of 15:5.6. Apply and cure for 5 days@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquakote Grey for use with Aquakote Blue'. Site applied, blue coloured (once applied), two-component epoxy coating. 'Aquakote Grey’ is the base coat and comprises of Parts A (grey liquid) & B (amber liquid) which are to be mixed in a 100:17 mass ratio and then applied in a wet film thickness of 200µm. Cure for 12 hours@10°C before applying top-coat. 'Aquakote Blue’ is the top-coat and comprises of Parts A (blue liquid) & B (amber liquid) which are to be mixed in a 100:17 mass ratio and then applied in a wet film thickness of 200µm. Cure for 12 hours@10°C. For use with water up to 23°C. Please note that 'Aquakote Grey & Aquakote Blue' are to be used in conjunction with each other. the approval does not cover 'Aquakote Grey and/or Aquakote Blue' when applied as a single coat.
'Tesnit BA-60'. Orange coloured aramid fibre/NBR gasket material. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
`Novapress 260`. Green coloured, compressed fibre material (bound with NBR), manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
`Ruby Veg Soft Soap/EasyJoint Uni`. Translucent, amber coloured, soya oil lubricant. Apply as per manufacturer's technical datasheet 'revision 2' dated '22/09/21'. For use with water up to 23°C.
'LATAMID 66 H2 G/30 BLACK F:3352'. Black coloured, injection moulded PA66 material. For use with water up to 65°C.
'CELANYL A2 WR GF30 NC 1102/2A & CELANYL A2 WR GF30 NC 1102/2B'. Off-white, injection moulded nylon materials. For use with water up to 85°C.
'POLYPOL-1052'. Pale yellow/beige coloured, isophthalic unsaturated polyester resin material. For use with water up to 50°C.
'VICTREX' injection moulded PEEK thermoplastic materials. For use with water up to 85°C. VICTREX PEEK 450GL30, 450G, 450FE20 (natural – appears beige coloured), 450FC30, 450CA30 & 90GL30BLK-EU (black coloured). VICTREX FG™100, FG™120, FG™200, FG™220, FG™300 & FG™ 325 (natural – appears beige coloured). VICTREX FG™101, FG™121, FG™140, FG™201, FG™221, FG™240, FG™301 & FG™320 (black coloured). VICTREX FG™340 (dark grey coloured).
'Lucite Diakon ST25G8 Clear 0003'. Colourless, injection moulded PMMA material. For use with water up to 23°C.
'AO Roto Water Tank Panel'. White coloured, LLDPE tank panel manufactured by rotational moulding. For use with water up to 60°C.
'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Total 4041 Blue Polyethylene & Total 4041 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
Page 16 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
