Range of full-bore spherical valves with bronze bodies, PTFE seats incorporating redox coated brass ball and various operating members (see models). Maximum working pressure 40 Bar Maximum operating temperature 95°C
Range of full-bore spherical valves with a brass body (nickel plated), brass ball (chrome plated) and PTFE seats. All models are available as lever operated, 15-28mm sizes are also available with a butterfly handle. For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 25.0 bar. BS6920 85°C.
In line isolation valve with DZR brass body, DZR brass ball (chrome plated), and an EPDM inlet washer. The product incorporates two approved check valve cartridges, one either side of the spherical valve, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar. BS6920 85°C.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of screw-down stop valves with brass bodies, incorporating a non-rising spindle operated via a T shaped (all models excluding 513042) or hand wheel operating member (model 513042 only) and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of screw down stop valves with brass bodies and EPDM gaskets. M profile press connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down angle valves (chromium plated brass) incorporating a dome or triangular type operating member with a NBR washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 8.6 bar. Cold water use only.
Range of undercounter water chillers with a stainless-steel cooling tank including a drain outlet. Maximum working pressure 3.0 Bar. Maximum operating temperature 38°C.
'PA-727 CM1404 White & PA-727 CM1405 Grey'. White or grey coloured, injection moulded ABS materials. PA-727 CM1404 White is for use with water up to 85°C. PA-727 CM1405 Grey is for use with water up to 23°C.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RAX Cement Mortar'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instructions 'WI-PRD-08', rev. '00', dated '01.02.2023'. Cure for 24 hours@28°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valcoat Blue'. Factory applied, blue coloured epoxy coating. Pre-heat the substrate and apply as per manufacturer's TDS with issue '01.04.2023'. Post-cure for 5-7 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Fibre Gulf'. GRP pipe which is has a brown/yellow coloured water contact layer and a beige coloured outer layer, manufactured by filament winding and contact moulding. For use with water up to 60°C.
'SUPIC-710PT GRP'. Beige coloured GRP material manufactured by hand lay. For use with water up to 23°C.
'PE-X.050'. Black coloured, extruded PEX hose. For use with water up to 85°C.
'POLIMID A SG NATURALE WR'. Natural (appears white in colour), injection moulded PA 66 material. In February 2025 'POLIMID A SG BLACK WR-PA66', black coloured, injection moulded PA 66 material was added to the approval. For use with water up to 85°C.
'DFC White HDPE Float 025RBX006HP'. White coloured, extruded and machined HDPE float component. For use with water up to 65°C.
'Borstar® RA150E'. Natural (appears off-white) polypropylene material for injection moulding and extrusion purposes. For use with water up to 85°C.
'Topilene R202P'. White coloured, extruded polypropylene material. For use with water up to 85°C.
'Bush (25122200)'. Dark grey coloured, extruded NEP-25%carbon/PTFE component. For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CH200'. Brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'version 24/05/2018'. Cure for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'9710-ALT 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size between 1.0mm & 2.0mm. For use with water up to 23°C.
'LOPI50'. Black coloured, injection moulded EPDM 'O'-ring. Shore hardness 50. Tested in-radius size 2.5mm. For use with water up to 85°C.
'EPDM 70.502-03 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'PT0165/2'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'HBHG'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AquaFlex T 5857'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
'NB7041F'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Griffon Silpat'. Grey coloured jointing compound. Apply as per manufacturer's instructions '7001669', issue '1'. For use with water up to 85°C.
'Griffon UNI-100 XT'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6300427', issue '1'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Wall mounted, metal, single outlet, fixed combination tap assemblies. Flow is controlled by a solenoid valve activated by via an infra-red sensor and temperature adjusted via a single lever operating member. The Inlets incorporate stainless steel strainers & approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled combination tap assemblies, (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. A stainless steel braided PEX lined flexible hose connects the components. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 45°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator and flow regulator. The tap incorporates a soap dispenser with separate dispensing nozzle. Maximum working pressure 8.0 Bar. Maximum operating temperature 55°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel or brass bodies – various finishes). Flow is controlled via solenoid valve (housed in a control box) actuated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The spout outlets incorporates plastic aerators. The products incorporate a stainless steel PEX lined flexible hose assembly, connecting the tap to the solenoid valve. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of break tanks and pump sets incorporating a Type AB airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10 bar. Cold water use only.
Range of AB air gap arrangements (verified by test - suitable for backflow protection against Fluid Category 5), supplied with or without softeners and/or flow meters (see models). Maximum working pressure 10 bar. Maximum operating temperature 85°C
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges within a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR seals and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Page 142 of 225
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
