`MECH WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions '24136' dated 2025/1/26. For use with water up to 85°C.
'EM6/35/7541/1'. Factory applied, dark blue coloured Porcelain (vitreous) enamel coating. Apply as per manufacturer's instructions 'IS_003', 'rev. 01'. Cure for 16 min 875°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carboguard AQP FC Part A and Part B'. Site applied, grey coloured (once applied) epoxy coating. Mix Parts A & B in a weight ratio of 1:1 and apply as per manufacturer's Product Data Sheet '8163', dated 'March 2025'. Cure Coat 1 for 24 hours at 20°C and Coat 2 for 7 days at 20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPS GRP Pipe'. Multi-layered, beige coloured GRP pipe, made by Continuous Filament Winding. For use with water up to 60°C.
'SANIBIW WB60 & SANIBIW WB80'. 'SANIBIW WB70’ was added to the approval in February 2026. Off-white coloured, transparent, extruded silicone rubber hoses. Shore hardness between 60 & 80. Tested in-radius size between 0.5mm & 1.5mm. For use with water up to 85°C.
'SL7065/SL7015'. Extruded, triple layered hose comprising of a translucent, silicone inner layer, white coloured polyester middle layer and translucent, silicone outer layer. Shore hardness 70. Tested in-radius size of complete hose is 1.8mm. For use with water up to 65°C.
'Rauaqua Varioflex Plus'. Multi-layered layered, extruded hose comprising of a white coloured, ethylene based plastomeric inner layer, white (transparent) coloured LDPE second layer, natural (appears white coloured, translucent) polyester third layer and blue coloured LDPE outer layer. For use with water up to 65°C.
'Grilon AG-30 FWA Black'. Black coloured, injection moulded, PA66-GF30 material. For use with water up to 85°C.
'S-Lon HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'PE002'. Blue coloured, HDPE fitting manufactured by mould pressing. For use with water up to 60°C.
'R579 TP13582 BLACK & R579 TP14619 BLACK'. Black coloured, rotomoulded PE materials. For use with water up to 85°C.
‘SABIC P6006AD’. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'KESHUN PPR Pipe'. Multi-layered, extruded PPR pipe comprising of a natural (appears off-white) inner layer, yellow coloured middle layer and green coloured (with red stripes) outer layer. For use with water up to 65°C.
'Hostalen PP H2222 36'. Grey coloured, compression moulded polypropylene material. For use with water up to 85°C.
'Cosmoplast D3 UPVC Pressure Pipe'. Grey coloured, extruded UPVC pipe. For use with water up to 65°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'51M7568'. Black coloured, injection moulded EPDM material. Shore hardness 75 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NBR 70 M066'. Black coloured, injection moulded NBR 'O' ring. Shore hardness 70. Tested in-radius size 3.0mm. For use with water up to 23°C.
'NE7130-XT'. White coloured (translucent), injection moulded Silicone rubber. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Vyncolit BXE650W'. Black coloured, injection moulded phenolic material. For use with water up to 85°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assembly (chromium plated brass). The flow is controlled via solenoid valve which is actuated by an infra-red sensor. The inlet of the 107.6826 model incorporates a stainless steel strainer. The 107.5603 model has an integral soap dispenser (separate to the water pathway). The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FLKIT40 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT60 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT80 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
Spring loaded, resilient trim, in-line check valve cartridges with plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim check valve cartridge with plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of assisted bathing units. The flow is controlled via an electronic thermostatic mixing valve which can feed either a bath spout outlet or shower handset. The discharge from both the bath spout and shower handset are via a type AUK 3 airgap, verified by measurement, suitable for fluid category 5 backflow protection. These bathing units have adjustable height and tilt functions. Maximum working pressure 6.0 Bar Maximum operating temperature 45.0°C
Range of ceramic cartridge headworks with plastic bodies, incorporating EPDM seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar (D40P-17 & D40G-17) or 20.0 Bar (D25G-6) Maximum operating temperature 85.0°C
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of ceramic cartridge and 2-way ceramic disc diverter headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with either stainless steel (models 49xxS604WF & 49xxP704WF only) or brass (all other models) bodies (various finishes). The products incorporate a ceramic cartridge headwork with either single lever, cylindrical or no supplied operating members (see models). The spout outlets incorporate a plastic aerator and model 58xxL904F is supplied with a lever operated pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 80°C.
Range of single hole, single outlet combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) bodies, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with a click type pop-up waste (not verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) bodies, incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. Products are supplied with click type pop-up wastes (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) bodies, incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a click type pop-up waste (not verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assemblies (Chrome finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a flow straightener. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Products supplied with a click type pop-up waste (not verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes), incorporating non-rising spindle headworks and single lever or dome type operating members. The spout outlet incorporates a plastic aerator. Supplied with a lever type pop up waste – not tested. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Models 6500H/W & 6504/W are supplied with a click type waste – not verified by test. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 235038 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type | |
| 223238 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole single outlet (fixed) combination tap assemblies (chrome plated), with a ceramic cartridge headwork and flow straighter in the spout outlet. Supplied with a click type waste (verified by test). Maximum working pressure - 5.0 bar. Maximum operating temperature - 60 °C.
Single hole single outlet (fixed) combination tap assemblies (chrome plated), with a ceramic cartridge headwork and flow straighter in the spout outlet. Maximum working pressure - 5.0 bar. Maximum operating temperature - 60 °C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass) bodies, incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Product supplied with a surface mounting kit comprising of Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” BSP captive nut end connections with 15x15mm compression isolation valves that incorporate single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Page 135 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
