'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KLINGERSIL® C-4324'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YT-002 (natural) & YT-003 (black)'. Extruded, natural (colourless) or black coloured PVC hoses. For use with water up to 65°C.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Glidex Tap Lubricant'. White coloured silicone lubricant. For use with water up to 60°C.
'Glidex Silicone Paste'. White coloured lubricant. For use with water up to 60°C.
'Bestnyl SI40VI02BD (PA 640GF BK)'. Black coloured, injection moulded PA6 material. For use with water up to 60°C.
'KN133G50 (beige coloured) & KN133G50BL (black coloured)'. Injection moulded PA6 materials. For use with water up to 65°C.
'Pemaron660G6W NC02'. Natural (appears beige in colour), injection moulded, glass fibre reinforced PA66 material. For use with water up to 23°C.
'DH-01 Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'DH-02 Fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 65°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'LL 8460.29'. Natural (appears white and opaque) LLDPE material manufactured by rotational moulding. For use with water up to 85°C.
‘RTP 199 X 146499 S-202865 White’. White coloured (opaque), injection moulded PP material. For use with water up to 50°C.
'Tamkeen Modern Pipe White, Light Grey and Dark Grey'. Extruded PVC pipes. For use with water up to 60°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'TIMO 7 NC-70 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
Page 121 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
