Range of overhead shower outlets with (brass bodies – various finishes) incorporating stainless-steel filter washers at the inlet. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HS183 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable | |
| HS2019 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable | |
| HS2018 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable | |
| HS3013 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable |
XXX Denotes the following: First, second & third different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of in-line bronze bodied ‘Y’-pattern strainers with stainless steel mesh. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T40217 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SL-T40218 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SL-T40217W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40218W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40107W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T41107 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T41108 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40807W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40808W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42107 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42108 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40807 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40808 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40806 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42106 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40806W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40106W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Aerator |
1. Various finish: (1) With suffix B: Black (2) With suffix BB: Brushed brass (3) Models SL-T40217, SL-T40218, SL-T40107W, SL-T40108W & SL-T40106W, with suffix G: Champagne Gold
CR27A Chrome Pillar tap with single lever or cross-top operating members incorporating a 1/4 turn ceramic disc headwork. The spout incorporates a flow straightener. Maximum pressure 10 bar. Maximum temperature 60 °C
GE01, GE01/501, CR19 & CR19/501 Pillar taps with single lever or cross-top operating members incorporating a 1/4 turn ceramic disc headwork. Models GE01 & GE01/501 incorporate a flow straightener. Maximum pressure 10 bar. Maximum temperature 60 °C
Range of EPDM hoses with either nylon or stainless-steel braiding, with or without a PVC sheath. Some models incorporate isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, thermostatic shower valves (brass body – various finishes), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM2 SHC3DIV C | Chrome | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, thermostatic shower valves with chromium plated brass body. Flow is controlled by a quarter turn ceramic disc headwork with single lever operating members. Temperature is controlled by a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The inlets incorporate a stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating a 2-way manual diverter to control the flow with cube type operating members. The temperature is controlled independently via a thermostatic cartridge with cube type operating member that incorporates a manual override button. The inlets incorporate stainless-steel strainer and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies. Maximum inlet supply pressure 8.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of adjustable, bronze in-line pressure reducing valves. ½”, ¾”, 1” & 1¼” size have inspection ports on the outlet only. 1½”, 2”, 2½”, 3” AND 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with DZR brass bodies. Handwheel operated. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with DZR brass bodies. Maximum working pressure: 20.0 Bar. Maximum operating temperature: 85.0°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
'Electrocement CEM1-SR3 - Dalmia SRPC'. Factory applied, grey coloured sulphate resisting Portland cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-4'. Factory applied, grey coloured Portland Cement. Mix sand, cement and water in a 40:20:40 weight ratio and apply as per manufacturer's instruction sheet 'Revision: A1', dated '2023-11-15'. Cure for 4 hours at 23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user manual 'TWJ/H--451PW-20250120', dated 'January 1, 2025'. Cure for 7 days for 25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'Sanibiw Dynamic'. Multi-layered, extruded hoses comprising of an off-white, transparent silicone inner layer, white, opaque PES yarn reinforcement layer and black coloured, silicone outer layer. The inner layer has a tested in-radius size of between 0.4mm & 0.8mm. For use with water up to 85°C.
'flomasta Silicone Spray'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 4', dated '23/05/2025'. For use with water up to 85°C.
'T-NO.100S-FD'. White coloured (translucent) PET mesh manufactured by weaving. For use with water up to 45°C.
'Bondrite S1010'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per TDS, issue date November 2021. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP HIGH Load Vinylester JFV380SF & JFV300SF’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 15/0704’, dated ‘31/01/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 15/0704’ then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'EPDM 70.54-02 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EPDM 70.54-02 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Flexrubber EW70 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'07148-60'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'WEICONLOCK AN 301-72 (white coloured) & WEICONLOCK AN 301-48 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'ONEBOND ADHESIVO PVC PROFESIONAL'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On® 773™'. Dark grey coloured solvent cement, intended to join ABS pipe and fittings. Apply as per manufacturer's data sheet '773-07-2025'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On® 795™'. Clear solvent cement, intended to join PVC pipe and fittings. Apply as per manufacturer's data sheet '795-07-2025'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, double outlet (fixed) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied). All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature 98°C. Hot-water circuit has a maximum operating temperature of 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH71 | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | |||
| GUTH61 * | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk |
Product Identification with an * as suffix = models added 11/082025
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Page 107 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
