'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'KH659R'. Black coloured, compression moulded, resin impregnated carbon ring. For use with water up to 85°C.
'KH659AC'. Black coloured, compression moulded, resin impregnated carbon ring. For use with water up to 85°C.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV17'. Factory applied, blue coloured, two-component epoxy coating. Mix coating and hardener in a weight ratio of 4:1 or volume ratio of 3:1 and apply as per manufacturer's TDS '01 – 11.06.2024'. Cure for 7 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PV7'. Green coloured (opaque), resin impregnated GRP pressure vessel body manufactured by filament winding. For use with water up to 65°C.
'WACKER® AK 350'. Colourless, transparent lubricant. For use with water up to 60°C.
'Paryls PPA A6200GLXX' (XX denotes the weight percentage of glass fibre between 30% to 50%). Black coloured, glass fibre reinforced polyamide materials manufactured by twin screw extrusion. For use with water up to 85°C.
'Vitamide AR86BK 1727/2 MAL'. Black coloured, injection moulded glass filled, PA66 material. For use with water up to 85°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'DEF HDPE Pipe'. Black coloured (with blue coloured external stripe), extruded HDPE pipe. For use with water up to 65°C.
'DEF HDPE Fitting'. Black coloured, injection moulded HDPE fitting. For use with water up to 65°C.
'DOKERLER HDPE fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
‘Polytank’. Multi-layered LLDPE tank panel, manufactured by rotational moulding, consisting of a white coloured inner layer, black coloured middle layer & white coloured outer layer. For use with water up to 65°C.
'Union Pipes Industry Fabricated Fittings'. Black coloured, extruded and welded, fabricated polytheylene fittings. For use with water up to 60°C.
'Novatherm Faser Composite Pipe’. Extruded, multi-layered pipe comprising of a green coloured, PP-R inner and outer layer and green coloured, glass fibre reinforced PP-R middle layer. For use with water up to 65°C.
'ISOMAG Cylinder'. Grey coloured, extruded polypropylene cylinder component. For use with water up to 60°C.
'VIALLI-De SDR 6 & SDR 7.4 PPR pipes'. Green coloured, extruded PPR pipes. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 Pipe with Aluminum Middle Layer'. Extruded PPR pipe with a green coloured inner and outer layer and aluminium middle layer. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 & SDR 7.4 Pipes with Glass Fibre Middle Layer'. Extruded PPR pipes with a green coloured inner and outer layer and a red coloured, glass fibre middle layer. For use with water up to 23°C.
'IROGRAN® A 85 P 4441 FCM'. White coloured, injection moulded polyurethane material. For use with water up to 60°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
'TIMO 3-70 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
‘TIMO 3-60 ‘O’ rings and gaskets’. Black coloured, injection moulded EPDM ‘O’ rings and gaskets. Shore hardness 60. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
'HT5557-20'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 60°C.
'AEC 2/EPDM-50, AEC 3/EPDM-60, AEC 4/EPDM-70 & AEC.A5/EPDM-80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'AquaFlex T 5821'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'6741'. Brown coloured, compression moulded FKM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 85°C.
‘Wall mounted, electronically operated tap assemblies (brass bodies - in various finishes). The flow is controlled by a solenoid valve that is actuated via an infra-red sensor on the spout. The spout outlet incorporates plastic aerators. Maximum working pressure 6 bar. Maximum operating temperature 65°C.
Range of spring loaded resilient trim check valve cartridges with plastic bodies, stainless steel spring and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 16 Bar Maximum operating temperature 65°C (model OV15/DN15-EPDM 31.0001.0 only) Maximum operating temperature 85°C for all other models
Spring loaded in-line check valve cartridges for insertion into pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Assisted bath incorporating a thermostatic mixing valve to control both the flow and temperature to either a spout outlet or shower handset. The discharge from the bath spout and shower handset in via a type AUK 3 airgap, verified by measurement, suitable for Fluid Category 5 backflow protection. The bath has adjustable height and tilt functions. Maximum working pressure: 6 Bar Maximum operating temperature: 45 °C
Range of quarter turn ceramic disc or non-rising spindle headworks (see models) with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating a ceramic cartridge headworks with single lever operating members. The product incorporates a pull-down hose incorporating plastic aerators and a trigger mechanism. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW104101110xx, TVW103004000xx, TVW125001000xx) are supplied with lever operated pop-up wastes (not verified by test). Models (TVW103005000xx, TVW104105110xx & TVW125002000xx) are supplied with click type pop-up wastes (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW105002000xx, TVW105003000xx, TVW105101110xx & TVW105141110xx) are supplied with lever operated pop-up wastes (not verified by test) Model TVW105105110xx) is supplied with a click type pop-up waste (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever type operating members. The spout outlet incorporates a plastic aerator and flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C
Range of single outlet fixed combination tap assemblies (chromium plated brass), incorporating a single sequential thermostatic cartridge controlling both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with a combined strainer, servicing valve that incorporates a single approved check valve cartridge verified by test, suitable for backflow protection to fluid category 2. Maximum working pressure 10 Bar Maximum operating temperature 65°C
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlets incorporate a plastic aerator and some of the models are supplied with lever type pop-up wastes.
Single-hole, single outlet (fixed) combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with single lever or dome type operating member. The spout outlets incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridges with single lever or dome type operating members. The spout outlets are either open outlet, waterfall or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators, flow straighteners, stainless steel strainers or open outlet type spouts (see models). Some models are supplied with a click type pop-up wastes, that have been verified by test (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with DZR brass adaptors for installation on each inlet. The adaptor incorporates a stainless-steel strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass body - various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop up waste (verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
Page 100 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
