'Sheraplex Blue, Black, Green & Silver'. Factory applied, organic resin coating system, consisting of a primer and 'Delta Seal' topcoat (available in blue, black, green and silver colours). Apply one coat of primer (as per instructions: WI.BMC.W02 Issue 2 - February 2005) and cure for 2 and ½ hours at 380°C. Then apply a passivation layer through immersion for 15 minutes at 76-99°C (as per instructions: WI.BMC.W06 Issue 1 August 2004). Apply 1 topcoat of 'Delta Seal' (as per instructions WI.BMC.W01A Issue 2 August 2010) and cure for 20 minutes at 200°C. All are for use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CSJX53-2 Red'. Factory applied, red coloured polyacrylic resin coating. Apply as per manufacturer's instructions file no. ‘CSJ-0016-1’, version no. ‘A1’, dated 2016.10.12. Cure for 50 minutes@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Primer coating Spu‐221(A) & Spu‐221(B)’ for use with ‘Top coating: Spu‐222(A) & Spu‐222(B)’. Factory applied, grey coloured (once mixed) Acrylic Polyurethane primer & coating. Mix parts A and B of the primer in a 4:1 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. Mix parts A and B of the topcoat in a 4:2 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2012-8-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'Interline 925P Light Grey & Interline 925P Off White'. Site applied, two component epoxy coatings. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's datasheet '10257', issue date '07/02/2022'. Cure for 7 days@25°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Nitocote EP405 (3821)’. Site applied, blue coloured, two component solvent free epoxy resin coating consisting of two bases (coat 1 base; Nitocote EP405 white & coat 2 base; Nitocote EP405 blue) & clear EP405 hardener. Mix parts A & B of each coat in a 100:13 weight ratio and apply in accordance with Fosroc data sheet issue 7 (CI/SfB: Pn6) dated November 2013. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Renderoc Plug 20'. Site applied, dark grey coloured, cementitious repair mortar. Mix with water in a 3:1 volume ratio and apply as per manufacturer's datasheet '14' dated 'June 2018'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Klüberbeta VR 67-17002'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Unisilkon L200'. White coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'YC-FM01'. Dark grey coloured, pressed and sintered Strontium Ferrite magnet. For use with water up to 85°C.
'Polimid A 50 GF Natural WR'. Natural (appears off-white/beige), 50% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
'Polimid A 50 GF Black WR'. Black coloured, 50% glass fibre reinforced, injection moulded PA66 material. Between June 2023 and May 2025, the material was for use with water up to 23°C. From June 2025, the material is for use with water up to 85°C.
'Polimid A 30 GF Black WR'. Black coloured, 30% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
‘AL ZAMIL roto moulded tank panel’. White coloured, roto-moulded, multi-layered PE tank panel. For use with water up to 60°C.
‘AL ZAMIL blow moulded tank panel’. Pale blue coloured, blow-moulded, multi-layered PE tank panel. For use with water up to 60°C.
'Danco Aquaflex PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'Elysee Wise PE100 Pipe'. Black coloured (with blue, external stripe), extruded HDPE pipe. For use with water up to 23°C.
'Kimplas Trustlene PE100 Electro-fusion fittings'. Black coloured, injection moulded Electro-fusion fittings. For use with water up to 65°C.
'Smart Joint Fitting'. Blue coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Smart Joint Fitting'. Black coloured, injection moulded HDPE fitting. For use with water up to 60°C.
'Smart Joint Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 60°C.
'Smart Joint Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 60°C.
'GS100ElPLAST'. Black coloured, extruded high density polyethylene pipe. For use with water up to 23°C.
'GS100ELPLAST'. Blue coloured, extruded high density polyethylene pipe. For use with water up to 23°C.
'BGS013'. Black coloured, LLDPE material manufactured by rotational moulding. For use with water up to 85°C.
'Genebre PTFE +15% Seats 18.0'. White coloured (opaque), injection moulded PTFE/fibreglass seats. For use with water up to 23°C.
'Venda Tapafugas Blinker'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet '01-02-29R R4'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'07148-70' components. Black coloured, compression moulded EPDM components with a shore hardness of 70. Sealing gaskets have an in-radius size of 1.0mm. Sealing membranes have an in-radius size of 0.92mm. Gasket membranes have an in-radius size of 0.85mm. Membrane seals have an in-radius size of 1.0mm. Sealing rings have an in-radius size of 1.0mm. For use with water up to 85°C.
‘07146-80’ components. Black coloured, compression moulded EPDM components with a shore hardness of 80. Sealing Gasket with an in-radius of 1.5mm. Membrane Seal with an in-radius of 1.0mm. Sealing Gasket with an in-radius of 1.0mm. Gasket Membrane with an in-radius of 1.0mm. Sealing Ring with an in-radius of 1.0mm. For use with water up to 85°C.
'ITK349601'. Black coloured, injection moulded EPDM C-seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E24 EPDM Type 2 Seals'. Black coloured, injection moulded EPDM seals. Shore hardness 75. Tested in-radius size of 0.77mm. For use with water up to 85°C.
'SEAEP70'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
'ML 57314'. Black coloured, compression moulded EPDM material. Shore hardness 68A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPDM-812-cm (70H/mid)'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'PT-EPDM55'. Black coloured, compression moulded EPDM material. Shore hardness 55. Tested in-radius size 1.1mm. For use with water up to 60°C.
'AEC.5/EPDM.80'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.1mm. For use with water up to 65°C.
'EPDM 773'. Black coloured, injection moulded EPDM sheet material (manufactured in Czech Republic). Shore hardness 50. Tested in radius sizes 0.9mm. For use with water up to 23°C.
'EPDM 798'. Black coloured, injection moulded EPDM material (manufactured in Czech Republic). Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Kingsun EP1702'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'XXE01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'JM-EP01'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Sunaflex T 8193'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AquaFlex T 5893'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'AquaFlex T 9696'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EUW-70'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 60°C.
‘SMS-8000-Premium’. Black coloured, compression moulded EPDM material. Shore hardness 80 respectively. Tested in-radius size 1.0mm. For use with water up to 23°C.
Page 95 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
