Concealed wall mounted thermostatic blending valve, (brass body – chrome trim set), incorporating quarter turn ceramic disc headworks with single lever operating members. Temperature is controlled independently via a thermostatic cartridge with a single lever operating member that incorporates a manual override button. The inlets incorporates approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of wafer type butterfly valves (lever or hand wheel operation) with a blue epoxy coated ductile iron body, EPDM seat and stainless-steel disc. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of blue epoxy coated butterfly valves with stainless steel discs and EPDM seal. Maximum operating pressure 16.0 bar. Maximum operating temperature 85°C.
Range of concealed diverter valves with (brass bodies), incorporating a ceramic disc diverter. The product can be supplied with a trim set and dome, lever or cross top type operating members (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pressure reducing valves with a DZR brass body, stainless steel strainer and EPDM membrane. Maximum inlet supply pressure 25.0 bar. Outlet pressure in the range of 1.0-6.0 bar. Maximum operating temperature 80°C.
Range of pilot operated, pressure reducing control valves with blue epoxy coated ductile iron bodies with stainless-steel isolation valves, tube and fittings. Maximum operating pressure 16.0 bar. Outlet pressure range is 1.0 to 10.0 bar (2PBL PRV) or 1.0 to 16.0 bar (2HC PRV). Maximum operating temperature 60°C.
Range of pressure relief valves with gunmetal bodies, EPDM diaphragms and lever operated easing gear. The relief setting is between 0.5 - 16.0 bar depending on the model. Maximum operating temperature 99°C
Range of pre-set pressure relief valves (spring loaded) with DZR brass body. Model 03521547 is set at 4.75 bar, 03521590 is set at 6.0 bar and 03541545 is set at 3.0 bar. Maximum operating temperature 85°C.
Pressure relief valve (pre-set at 3.0 bar) with a plastic body. The valve incorporates a manually operated easing gear. Maximum operating temperature 90°C.
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of servicing valves with chrome plated brass balls and brass bodies (chrome plated) with either lever operating or butterfly operating members (see models). Compression connection to be used with copper pipe EN1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of lever or butterfly operated spherical valves with brass or nickel-plated brass (CC617 and Arc89) or DZR brass bodies (CCDZR). Incorporating brass or nickel-plated brass (CC617 and Arc89 ) or DZR brass ball (CCDZR). For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball, (DZR brass body and ball on FFDZR prefix models). Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Range of bronze bodied gate valves incorporating brass wedges with PTFE packing. Maximum Pressure 16.0 bar. Maximum operating temperature 100°C.
Range of hand wheel operated gate valves with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with Red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with DZR brass bodies, stems and discs. The valves operate via a hand wheel (non-rising) and a metal to metal seal. Valves are for above ground use only. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of EBCO stop valves with gunmetal bodies with a various end connections. Maximum working pressure 16 bar. Cold water use only.
Activflo Lite range of water conditioners with copper bodies. Models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of UV disinfection units, for above ground use only. Maximum operating pressure 10.0 bar. Cold water use only.
“CN Pressure vessel” range incorporating a HDPE liner. The products have a separate outer layer (with black, blue, grey or natural finishes). The CN Pressure vessel 24x72” D-4 model has a top and bottom opening. Maximum operating pressure 10.5 bar. Cold water use only.
'KH369R'. Black coloured, compression moulded Carbon ring which is impregnated with Phenolic Resin. For use with water up to 85°C.
'Spectrum Carbon Block'. Black coloured, extruded activated carbon block. From March 2026 it can also be manufactured by sintering. For use with water up to 23°C.
'Relithane 151. Factory applied, brown coloured, two-component Polyurethane coating. Mix base and hardener in a 2.5:1 ratio and apply as per manufacturer's 'Standard Operating Procedure & Guidelines, Revision 2, 157/2022' dated 12th October 2022. Cure for 40 seconds@35°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 8423'. Factory applied, dark blue coloured enamel coating. Apply as per manufacturer's TDS '08423', version '02-2024' and cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotun Marathon IQ2'. Factory applied, two-component, grey coloured epoxy coating. Mix parts A:B in a ratio of 3:1 parts and apply as per 'Jotun Marathon IQ2' Technical Data Sheet dated '16 April 2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI Hygienic CML'. Factory applied, grey coloured cement mortar. Mix cement mortar:sand:water in a weight ratio of 36:46:18 and apply as per manufacturer's instructions 'LMICMA012624', dated '1/26/2024'. Cure for 20 hours@40°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Alsen FBE Blue Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'AIPL 1212/1', dated '07/06/2023'. Cure for 2.5 hours:235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSC-01'. Factory applied, grey coloured cement mortar. Mix sand:water: cement in a 1.5:1.0:1.0 weight ratio and apply as per manufacturer's instructions 'GB0012023', edition 'A1'. dated '2023-10-10'. Cure for 24 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flexseal 163 Green`. Green coloured, compressed synthetic fibre sheet material manufactured by calendaring. For use with water up to 23°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'SUS-GRP01'. White coloured GRP panel manufactured by hot press moulding. For use with water up to 65°C.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Neama Liner Sand Filter'. Off-white coloured (translucent), rotationally moulded LLDPE filter. For use with water up to 65°C.
'Cosmoplast HDPE Pressure Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 65°C.
'INVA by Rarean'. Black coloured (with blue external stripe), extruded PE pipe. For use with water up to 65°C.
'Cosmoplast UPVC Pressure Fitting D3 Compound'. Grey coloured, injection moulded UPVC fittings. For use with water up to 65°C.
'WRAS 61713 EB 78'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 78D. Tested in-radius size 1.05mm. For use with water up to 60°C.
'WRAS 61813 E80'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 2.2mm. For use with water up to 60°C.
'SME001 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 60. In November 2024 'SME001 EPDM', a compression moulded EPDM rubber with a shore hardness of 75 was added to the approval so that a range with a hardness between 60 & 75 is covered by the approval. Tested in-radius size of 1.0mm and are for use with water up to 65°C.
'E59WKZ'. Black coloured, injection moulded EPDM rubber material. Shore hardness 58. Tested in-radius 1.0mm. For use with water up to 60°C.
'HT5557-10'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. Between January 2024 and March 2024, the material was for use with water up to 50°C. From April 2024 the material is for use with water up to 60°C.
'WN12/7/1 BLK 'O'-rings'. Black coloured, injection moulded NBR 'O' rings. Tested in-radii sizes between 0.89mm and 2.0mm. Shore hardness 70. For use with water up to 65°C.
Page 84 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
