Solenoid valve with a plastic body and an EPDM membrane, which is inserted into a brass housing with EPDM ‘O’-rings. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of spherical valves with a single lever or ‘T’ handle operating member. The products have a DZR brass body and a chrome plated DZR brass ball, except for the models with the ‘-OT’ suffix, models have (nickel-plated brass bodies) and chrome plated brass ball. The products are supplied with various end connections (see model). Maximum working pressures: 15mm to 28mm = 40 Bar 35mm = 25 bar 42mm to 54mm = 16 bar (All models). 42 to 54mm = 10 Bar (4E05, 4E05-OT, 4E06 and 4E06-OT models) Maximum operating temperature 40.0°C
Range of lever operated spherical valves with DZR brass bodies, chromium plated brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar Maximum operating temperature 85°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with nickel plated brass bodies incorporating chromium plated brass balls. For use with copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with brass bodies (nickel plated) and brass (chromium plated) balls, PTFE seats and NBR o-rings. Maximum working pressure: ½” to 1” = 40.0 bar, 1¼” to 2” = 25.0 bar. Cold water use only.
Range of press fit spherical valves with DZR brass bodies and balls. For use with copper pipe (EN1057) and stainless steel pipe (EN10312) Maximum working pressure 17.2 bar. Maximum operating temperature 100°C.
Range of spherical valves with chrome plate brass bodies, chrome plated brass balls and PTFE seats. For use with motorized actuator (not included) Maximum working pressure: ½” to 1” = 40.0 bar and 1¼” to 2” = 25.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Screwdriver operated spherical servicing valve with chromium plated brass body, brass ball and EPDM O-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with bronze bodies, incorporating PTFE seats and chromium plated brass balls. Maximum working pressure 40.0 bar. Maximum operating temperature 100°C.
In-line spherical valve with a chrome plated DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM, EPDM gasket and NBR O rings. The valves incorporate a non-rising spindle headwork. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM and EPDM gaskets. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with bronze bodies, bronze wedge, PTFE stem packing and non-rising spindles. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of globe valves with bronze bodies, brass (½”-1”) or bronze (1¼”-2”) disc, PTFE packing and a non-rising spindle headwork with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of stop valves with either DZR brass, brass, bronze or chrome plated bodies with T-type or lockshield (LS) operating members. Compression models are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of combination valves consisting of an in-line adjustable pressure reducing valve (between 1.5 and 6.0 bar) and a pressure relief valve, with DZR Brass bodies, EPDM `O`-rings and an EPDM diaphragm. CWIC110004 model - Pressure reducing valve pre-set at 3.5 bar and pressure relief valve set at 6.0 bar. CWIC200055 model - Pressure reducing valve pre-set at 3.0 bar and pressure relief valve set at 4.5 bar. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum supply pressure 16.0 bar. Outlet pressure range 1.5 bar to 6.0 bar (both models). Maximum operating temperature 20°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Activflo range of water conditioners with stainless steel bodies. Models with compression connections are for use with copper pipe (manufactured to BS EN 10 57), stainless steel pipe (BS EN 10312:2002), polybutylene (BS 7291-2) or PE-X pipe (BS7291-3). Maximum working pressure 16 bar. Maximum operating temperature 99°C
'KOCETAL GF305'. Off-white coloured, injection moulded POM material. For use with water up to 65°C.
'Seal Face PS5000'. Grey coloured, moulded and sintered silicon carbide washer. For use with water up to 85°C.
'Pearlbond PUP SF2K Primer and DuraPearl HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply 'Pearlbond PUP SF2K Primer’ as per Product Data Sheet '2023-02-27'. Cure for 2 hours@25°C. Then mix and apply ‘DuraPearl HP 500 PW Coating' as per Product Data Sheet ‘210705’. Cure for 1 minute@25°C. For use with water up to 85°C.
'FP60 Dark Blue'. Factory applied, dark blue coloured epoxy powder coating. Mix and apply as per manufacturer's TDS 'FP60/Rev:3' October 2020. Cure for 10 minutes@160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YHGuard8680 Primer & YHChlor6200 Topcoat'. Factory applied, blue coloured (once applied), coating system comprising of an epoxy primer and polyethylene topcoat. 'YHGuard8680 Primer’ comprises of a binder and hardener to be mixed in a 30:2.5 weight ratio before being applied as per manufacturer’s data sheet ‘8680 20220601’. Cure for 12 hours@25°C. Apply ‘YHChlor6200 Topcoat' as per manufacturer’s data sheet ‘6200 20220601’. Cure for 5 hours hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPL Gold Portland Slag Cement'. Grey coloured, factory applied Portland Slag cement. Mix cement, sand & water in a 1:1.4:0.35 mass ratio. Apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours@27°C, 70% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's product information dated 'August 16,2022'. Cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/013', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Blast Furnace Slag Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/012', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'DPFC GRP Pipe'. Beige/straw coloured GRP pipe manufactured by filament winding. For use with water up to 50°C.
'ILPEA 70-90 EPDM HOSE WRAS AF'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.3mm. For use with water up to 23°C.
'SYL-8668'. White coloured (opaque) grease. For use with water up to 70°C.
'G. BESLUX BESSIL 6001'. White coloured, opaque silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'CELANYL A3 WR GF30 NC 1102/Z/FA'. Natural (appears cream in colour), injection moulded polyamide material manufactured in Celanese(Suzhou) Engineering Plastics Co. LTD (China), & Celanese Production Germany GmbH &Co (Utzenfeld –Germany. For use with water up to 85°C.
'Taldeen Electrofusion Fitting'. Black coloured, injection moulded, PE100 Electrofusion Fitting. For use with water up to 85°C.
'Taldeen PE100 Pipe'. Black coloured (with blue external stripe), extruded, PE100 Pipe. For use with water up to 85°C.
'Jain HDPE (PE 100) Blue Fittings). Blue coloured HDPE fittings manufactured by injection moulding or extrusion. For use with water up to 65°C.
'Rainson HDPE (PE100)'. Black coloured, injection moulded HDPE (PE100) material. For use with water up to 23°C.
'P901BK'. Black coloured, extruded HDPE material. For use with water up to 23°C.
'Revolve N-250 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'PPELXS314G20NA'. Beige coloured, injection moulded PPE material. For use with water up to 85°C.
'AY-N130X series'. Injection moulded PPE materials. For use with water up to 85°C. • AY-N130X-GY843 – grey coloured (contains 30% maximum glass fibre, 2% maximum white pigment, 0.01% maximum black pigment). • AY-N130X-YW05 – yellow coloured (contains 30% maximum glass fibre, 1.5% white pigment, 0.5% maximum yellow pigment). • AY-N130X-BK001 – black coloured (contains 30% maximum glass fibre, 0.5% maximum black pigment).
'Xytron™ G3010E BK00001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Topilene® R200P (colourless) & Topilene® R200P-3702 (grey coloured)'. Extruded polypropylene pipes. For use with water up to 85°C.
'Borealis HB601WG'. Clear, injection moulded polypropylene material. For use with water up to 85°C.
'Meplen EH FXX T & Meplen EH FXX T BK'. Natural (appears beige coloured) or black coloured, injection moulded polypropylene materials. XX denotes glass fibre content between 10 and 50%. Both are for use with water up to 85°C.
3M™ Dyneon™ Fluoroplastic grades - FEP 6301Z, FEP 6303Z, FEP 6307Z, FEP 6322Z and FEP 6322HTZ. Natural coloured FEP materials manufactured by melt-processing. For use with water up to 85°C
Page 76 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
