Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
2Z126 FGAXXXB16NS01 range of brass gate valves or FGAXXXD16NS42 range of DZR brass body gate valves, with PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (MV40-1138.RS, MV40-1138 & MV40-1138.D models). Bronze body, bronze wedge and lock-shield (MV40-1153.LS & MV40-1138.LS models). Brass body, brass wedge and handwheel (MV40-1120 model only). Maximum working pressure 20.0 bar & 25.0 bar (model MV40-1153.LS only). Maximum operating temperature 85°C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
'Iupital F10-EW'. White coloured, injection moulded POM material. For use with water up to 85°C.
'TENAC-C 4590'. White (translucent) coloured, injection moulded acetal material. For use with water up to 85°C.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF-CM1'. Factory applied, grey coloured, sulphate resistant cement mortar. Mix cement mortar, sand & water in a 2:1:0.4 mass ratio and apply as per manufacturer's user instructions 'SF-CM1', 'Vision A1' dated '2024-7'. Cure for 12 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM119-1'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no.: LM-001', 'Edition: A', 'Issue date: 2024-JAN.-15th'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'F15222 CB Silicone Lubricant' & 'PHCB042 – F15222 Centerbrand Silicone Grease'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Latigloss 66 H2 G/50 Nat.:0003F2 (appears beige coloured) & Latigloss 66 H2 G/50 Black:3352F2 (black coloured)'. Injection moulded PA66 materials. For use with water up to 85°C.
Tecomid NA40 GR25 NL HS QF (white coloured) and Tecomid NG40 GR30 BK250 HS QW, Tecomid NA40 GR30 BK005 HY QH & Tecomid NA40 GR30 BK250 HY QW (black coloured). Injection moulded PA materials. Tecomid NA40 GR25 NL HS QF (white coloured) & Tecomid NG40 GR30 BK250 HS QW (black coloured) are suitable for use with water up to 85°C. Tecomid NA40 GR30 BK005 HY QH (black coloured) & Tecomid NA40 GR30 BK250 HY QW (black coloured) are suitable for use with water up to 23°C.
'Radius Systems Puriton Dark Blue Barrier Pipe [Type A, BS8588]'. Extruded, multi-layered pipe comprising of a black coloured PE100 inner layer, aluminium middle later and dark blue coloured PE100 outer layer. For use with water up to 23°C.
'Elysee HDPE PE 80 Blue Pipe'. Extruded, single layered (blue coloured) or dual layered (black coloured inner layer & blue coloured outer layer) HDPE pipes. For use with water up to 23°C.
'Flomasta Blue PE 80 Pipe'. Extruded, single layered (blue coloured) or dual layered (black coloured inner layer & blue coloured outer layer) HDPE pipes. For use with water up to 23°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'BLAZE PPR01'. Green coloured (with red external stripe), extruded polypropylene pipe. For use with water up to 85°C.
Page 561 of 578
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
