‘2KPS EASF-VE’. Site applied, two part, grey coloured anchor resin. 2KPS EASF-VE is light grey coloured when mixed and consists of Part A (shiny grey coloured liquid) & Part B (shiny off-white coloured liquid). Mix, apply and cure as per manufacturer’s product information sheet 'EASF-V / VC / VE (EU07) V4.0'. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'4360 'O' rings, washers, membranes and lip seals'. Black coloured, injection moulded EPDM components with a shore hardness of 60. The ‘O’ rings have a tested in-radius size of 1.31mm. The washers have a tested in-radius size of 1.05mm. The membranes have a tested in-radius size of 1.55mm. The lip seals have a tested in-radius size of 0.40mm. For use with water up to 85°C.
'7EP1197 Gasket'. Black coloured, extruded EPDM gasket. Shore hardness 70. Tested in-radius size 0.5mm. '7EP1197 'O'-rings' were added to the approval in March 2023. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'KEP EPDM Butterfly Valve Seat'. Black coloured, compression moulded EPDM sheet. Shore hardness 70. Tested in-radius size 1.6mm. For use with water up to 23°C.
'EP01961PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CVE78'. Black coloured, extruded EPDM material. Shore hardness 80. Tested in-radius size 10.0mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPH-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘KRE 60 (103), KRE 65 (100) & KRE 65 (106)’. In September 2022 ‘KRE 60 (104)’ was added to the approval. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60 & 65. Tested in-radius size 1.0mm. For use with water up to 60°C.
'TIMO 3-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EX60LC, EX70LC & EX80LC'. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60, 70 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'HT5697-5'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 1.0mm. For use with water up to 50°C.
Black coloured, compression moulded EPDM materials with a tested in-radius size of 1.3mm. 'EPW-50, EPW-55, EPW-60, EPW-65, EPW-70 & EPW-75' have a shore hardness of between 50 & 75 and are for use with water up to 23°C. ‘EPW-80' has a shore hardness of 80 and is suitable for use with water up to 85°C.
'EH600-151'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'H600042'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 65°C.
'6741'. Brown coloured, compression moulded FKM rubber. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SL70L41F'. Blue coloured, compression moulded silicone rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'Permabond ET5365'. Site applied, grey coloured, two-component epoxy adhesive consisting of part A (light grey coloured paste) & part B (dark grey coloured paste). The product cartridge is heated to 30°C and the two-components are mixed in a 2:1 volume ratio. Apply as per manufacturer's TDS 'revision 1', dated 23 May 2018. Cure 24 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interflon Paste HT1200'. Cream coloured ceramic paste. Apply as per manufacturer's instructions, document number 'IFUHT1200' dated 24/04/2017. Cure for 5 minutes@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted electric showers with plastic bodies. Flow is controlled by a solenoid. The product is supplied with a shower hose and a shower handset (white or chrome plated - depending on model). Maximum working pressure 8.0 bar. Maximum operating temperature 55°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass finish). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator and a stainless-steel strainer on the inlet. Maximum working pressure 8.0 Bar Maximum operating temperature 70.0°C
Range of electronically controlled taps (chromium plated brass). The assemblies incorporate a touch sensitive device and are supplied with a solenoid valve to control the flow. Spout outlet incorporates a plastic aerator and the product is supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of pressurisation units with flow controlled by a float operated valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate stainless steel strainers, flow restrictors and spherical isolation valves. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and NBR or EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of hot-pressed sectional cold water storage cisterns for wholesome water. The cisterns can either be galvanised or primed and site coated and are fitted with a float operated valve, screened air vents, overflow pipe and breather. The cisterns can also be fitted with a coated, carbon steel ladder. Cold water use only.
Single hole, single outlet (fixed, with swivel nozzle) bidet combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated, pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
‘Bubblestream’ range of tap outlet (stream shaper) adaptors incorporating a swivel mechanism and a stainless steel mesh aerator. All models, apart from 07.9870.0, are supplied with a M22 to M24 adaptor. All models, apart from 07.9870.0 & 07.9880.0, incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of aerators with plastic bodies and filter screens. Maximum operating temperature 60°C
Rising spindle headwork with a brass body intended to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of ceramic disc headworks with plastic bodies for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic elements with copper bodies. Maximum operating temperature 90°C.
Single-hole, single outlet (swivel) combination tap assembly with brass body (chrome plated), incorporating a ceramic cartridge headwork with a single lever operating member. The product has a pull-out spray outlet which incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The cold inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with pull-down hose. Incorporating a brass body (various finishes) and a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with pull-down hose. Incorporating a brass body (various finishes) and a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with single lever operating member and pull out spray handset. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet are pull-out spray type, which incorporates aerators and approved single check valve cartridges, however the complete assemblies have not been tested to demonstrate backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.°C
Single hole, single outlet (swivel) combination tap assembly stainless steel (various finishes), incorporating a ceramic cartridge headworks with single lever operating member and pullout spray handset. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or for model SM BAS C an aerator with 4.5l flow limiter - flow limiter performance is not tested as part of the regulators specifications). The product is supplied with an approved click-type waste. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C
Single-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with an approved click-type waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporates an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, brass bodies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with approved pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and the products are supplied with lever operated pop up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator and the products are supplied with a click waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet, fixed combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporate an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating quarter turn ceramic disk headworks with single lever operating members. The cold water inlets is supplied with a chrome plated brass adapter incorporating an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate plastic aerators. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Page 47 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
