'Jotapipe IL 6001-120S'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS dated 22nd August 2018. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ultramid® D3EG12 Aqua BK102'. Black coloured, injection moulded polyamide material. For use with water 85°C.
'Cool-FIT 4.0 & 2.0 Pipes'. Triple layered, extruded polyethylene pipe which comprises of a black coloured inner layer, off-white coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'Cool-FIT 4.0 & 2.0 Fittings'. Triple layered, injection moulded electrofusion fittings which comprise of black coloured inner layer, ivory coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'557WE, 557WG & 557WM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60, 70 & 90. Tested in-radius size 0.85mm. For use with water up to 85°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
'KX-1'. Black coloured, compression moulded, EPDM rubber sheet material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Initial approval was for ‘SMS-80’ (shore hardness 80) only. In April 2024 ‘SMS-50' (shore hardness 50) & ‘SMS-70’(shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AquaFlex T 5858'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EPDM70-BH'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DN-070WN 'O' rings'. Black coloured, compression moulded NBR 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 2.5mm. For use with water up to 23°C.
'TEC S27 R.-60 rosso 'O'-rings' & Gaskets. Red coloured, injection moulded silicone rubber 'O'-rings & gaskets. Shore hardness 60. Tested in-radii sizes between 0.5mm & 2.67mm. For use with water up to 85°C.
Wall mounted electric heater, incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type with brass ½’’ or ¾” BSP inlet. The inlet incorporates a strainer, models incorporate a delay fill function. The bottom entry valves are height adjustable. Maximum working pressure - 10 Bar, Cold water use only.
In-line non-verifiable check valve assembly with integral isolation valve. Consisting of spring loaded resilient trim check valve cartridge housed within a DZR brass body, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of aerators with plastic bodies and EPDM ‘O’-rings. Open outlet use only. Maximum operating temperature 65ºC.
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Page 387 of 582
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
