Range of thermostatic bar shower mixers, incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type of operating member. The temperature is controlled independently via a thermostatic mixing cartridge incorporating a manual override button. Inlets incorporate single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with a shower hose, handset and a riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of thermostatic bar shower mixers, (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with a dome type operating member. Temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. The Inlets incorporate stainless steel strainer washers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of butterfly valves with an epoxy coated ductile iron body, stainless steel disc and single lever or handwheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of concealed and exposed two-way diverters, (brass bodies – various finishes, trim sets and operating members). The inlets on XX1650YY and XX1721YY models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C (PSA019 YY, PSA020 YY & XX1782YY) Maximum operating temperature 60°C (PSH049, XX1650YY, RZ/1721 & XX1721YY).
Range of in-line manually adjustable pressure reducing valves with a DZR brass body (brushed chrome finish). Compression models are for use with coper pipe (manufactured to EN 1057). The MINIPRVG model is supplied with a gauge. Outlet pressure adjustable from 0.8 to 4.0 bar. Maximum inlet supply pressure 15.0 bar. Maximum operating temperature 80°C.
Range of monostable/normally closed pilot operated solenoid valves mounted in plastic bodies. Valve bodies can also be mounted together in multiples. Push-fit connections to be used with PTFE tube. Maximum working pressure 10 bar. Maximum operating temperature 70°C.
Range of latching or normally closed solenoid valves with plastic bodies and a silicone diaphragm. The products incorporate a plastic flow regulator on the outlet. The R197 model has a Ø13mm ID outlet for customers to insert their own outlet connections into. Maximum working pressure 10.0 Bar Cold water use only.
Range of spherical valves incorporating nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Instantor lever action ball valves with brass bodies, chromium plated brass balls and PTFE seats. Maximum working pressure 25 bar. Maximum operating temperature 85°C
Range of lever operated spherical valves with brass bodies, ball and PTFE seats and incorporates two single check valve assemblies (verified by test, suitable for backflow protection against Fluid Category 3). Compression models are for use with BSEN 1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Range of gate valves, (brass bodies) controlled via a handwheel with PTFE seals. Maximum working pressure 20.0 bar (L198 models), 16.0 bar (L197 & P474 models). Maximum operating temperature 99°C
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'TC-7808-19'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's data sheet dated June 8, 2019. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP015-UTB'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions reference 'PR-CA-00-024' dated 15-02-19. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Page 33 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
