Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, exposed, bar type thermostatic blending valves with brass bodies (chrome or matte black plated), incorporating quarter turn ceramic disc headwork controlling/diverting the flow. Temperature is controlled independently with a thermostatic cartridge with manual override button. Models MSSHFIRO & MSSHFIROBL have single lever type operating members. The inlets incorporate a stainless steel strainer and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature of 75°C.
Wall mounted, thermostatic shower valve (chromium plated brass body) incorporating a two-way diverter valve headwork that controls flow between each shower outlet with a cube type operating member. The temperature is controlled independently via a thermostatic cartridge with a cube type operating member with a manual override button. Both inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85°C.
Wall mounted thermostatic bar shower mixer, (brass bodies) incorporating quarter turn ceramic disc headwork controlling the flow with cubed or dome type operating members. The temperature is controlled independently via a thermostatic cartridge cube or dome type operating members incorporating a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, thermostatic shower valves with chromium plated brass body. Flow is controlled by a quarter turn ceramic disc headwork with single lever operating members. Temperature is controlled by a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The inlets incorporate a stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating a 2-way manual diverter to control the flow with cube type operating members. The temperature is controlled independently via a thermostatic cartridge with cube type operating member that incorporates a manual override button. The inlets incorporate stainless-steel strainer and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: 4925, 4925B, 4925G, 4923 & 4923G = 25.0 bar, 970W, 970WB, 970WG, 973W & 973WG = 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: FM638, FM638B, FM639, DM638 & DM639 = 25.0 bar, F624, F624B, F625, DM925LW & DM925G = 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless steel (CF8M) discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gear operated butterfly valves with blue epoxy coated ductile iron bodies and discs, incorporating hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of flow control valves with blue epoxy coated ductile iron bodies. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 65°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of tilting disc non-return valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of non-return valves with ductile iron bodies and discs. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 65°C.
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies. Maximum inlet supply pressure 8.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of adjustable, bronze in-line pressure reducing valves. ½”, ¾”, 1” & 1¼” size have inspection ports on the outlet only. 1½”, 2”, 2½”, 3” AND 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 model has a rising spindle, the BT1401 model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with DZR brass or brass bodies, incorporating PTFE stem packing and gaskets and handwheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with DZR brass bodies. Maximum working pressure: 20.0 Bar. Maximum operating temperature: 85.0°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
Range of water conditioners with stainless steel bodies. AFL012 MFB has a matt black finish and AFL012MFC has a chrome plate finish. Models with compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of UV disinfection units with titanium bodies.
'JDFF-OPC-01'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a 1:2:0.50 weight ratio and apply as per manufacturers Work Instruction 'WI-Pc-01-5', 'Issue #: 5 Revision #: 1', dated '10.01.2025'. Cure for 48 hours@23°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-4'. Factory applied, grey coloured Portland Cement. Mix sand, cement and water in a 40:20:40 weight ratio and apply as per manufacturer's instruction sheet 'Revision: A1', dated '2023-11-15'. Cure for 4 hours at 23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 83275'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS-2025-AL83275-REV00', dated '03.07.2025'. Cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user manual 'TWJ/H--451PW-20250120', dated 'January 1, 2025'. Cure for 7 days for 25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Bondrite S1016'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's TDS, issue date 'April 2025'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'Loxeal Olio 1000'. Clear, silicone oil based lubricant. For use with water up to 70°C.
'PE002'. Blue coloured, extruded HDPE pipe. For use with water up to 60°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
'Plate PE 100 natur'. White coloured (translucent), extruded, polyethylene 'support' component. For use with water up to 85°C.
'Locking Pin NGAB-00707'. Off-white coloured (translucent), extruded polypropylene pipe. For use with water up to 85°C.
'Bondrite S1010'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per TDS, issue date November 2021. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP HIGH Load Vinylester JFV380SF & JFV300SF’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 15/0704’, dated ‘31/01/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 15/0704’ then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Page 222 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
