Range of non-rising spindle gate valves with DZR brass or brass bodies, incorporating PTFE stem packing and gaskets and handwheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with DZR brass bodies. Maximum working pressure: 20.0 Bar. Maximum operating temperature: 85.0°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
'Delrin® FG51HS'. White coloured (opaque), injection moulded POM material. For use with water up to 23°C.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-4'. Factory applied, grey coloured Portland Cement. Mix sand, cement and water in a 40:20:40 weight ratio and apply as per manufacturer's instruction sheet 'Revision: A1', dated '2023-11-15'. Cure for 4 hours at 23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user manual 'TWJ/H--451PW-20250120', dated 'January 1, 2025'. Cure for 7 days for 25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Bondrite S1016'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's TDS, issue date 'April 2025'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'NEMA G10'. Green/yellow coloured, hot pressed GRE material. For use with water up to 50°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'SILICOMPOUND FCA 125'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Molykote® G-5511'. White coloured (opaque), silicone based grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'aquatherm PE-RT pipe'. Off-white coloured, extruded PE-RT (Type 1) pipe. For use with water up to 65°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
'Plate PE 100 natur'. White coloured (translucent), extruded, polyethylene 'support' component. For use with water up to 85°C.
'T-NO.100S-FD'. White coloured (translucent) PET mesh manufactured by weaving. For use with water up to 45°C.
'Bondrite S1010'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per TDS, issue date November 2021. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP HIGH Load Vinylester JFV380SF & JFV300SF’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 15/0704’, dated ‘31/01/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 15/0704’ then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'B8066'. Black coloured, compression moulded Chlorobutyl rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
'3W10-70-IR'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 1.75mm. For use with water up to 85°C.
'HC-EP7001165PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'07148-60'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SML-EP012EB'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C. When processing an application for WRAS Product Approval the in-radius tolerance rule cannot be applied, i.e. only the material with an in-radius of 1.0mm is covered by the scope of the approval.
'EPDM SP-002 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'Bondrite A2577'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of single hole, double outlet (fixed) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied). All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature 98°C. Hot-water circuit has a maximum operating temperature of 65°C.
Bottom entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and adjustable float and a plastic flow regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH71 | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | |||
| GUTH61 * | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk |
Product Identification with an * as suffix = models added 11/082025
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM 3WDIV C | Chrome | 15mm Compression | 10 bar | 60 °C | Bristan | Faceplate | No | Not applicable | Not Applicable | Not Applicable |
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-verifiable double check valve assemblies with DZR brass or chrome plated DZR brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Single hole, single outlet (swivel nozzle) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 812003A | 23.8mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812038A | 23.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812049A | 19mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812056 | 18.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812057 | 19.0mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812072 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812073 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812114 | 18.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30D-9 | 29.91mm | 10 bar | 85 °C | WANHAI, WRAS, 30D-9, Production date (DD/MM/YYYY) | Body | No |
Range of thermostatic cartridges with plastic bodies, stainless steel strainers and EPDM ‘O’-rings. Maximum operating temperature 85°C. Open outlet use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 233308 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Page 194 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
